R1 Custom Firmware available!As promised, I am releasing my customized firmware to the community. Please note that although I refer to this package as custom firmware, it is really just a patch file. If you reset your R1 to factory defaults, you will lose the customizations. In which case, you would just need to re-apply the patch.
Changelog for release 0.95:- Opened up port 4029 for API access to cgminer-u3 instance
- Max frequency for U3 increased to 250M
- Max fequency for R1 increased to 250M (I have not personally tested freq past 125. Use at your own risk!)
Firmware Enhancements- U3 zombie handling(Scripted auto-cgminer restarts and R1 reboot if necessary)
- Supports modifying R1 pools from UI, without losing the ability to use Bitmain's solo pool for R1.
- Detailed R1 stats page, including pool statistics
- Supports modifying R1 freq and voltage from UI
- U3 freq selection increased to 250M
- Cgminer-U3 API open for monitoring with 3rd party tools
WARNING: These customizations provide the ability to push your R1 beyond its intended limits. Because of this, it will likely void your warranty with Bitmain. Additionally, I provide this patch with no official support, and take no responsibility for any damage done to your R1 device or its surroundings. Use at your own risk! By downloading and applying this patch, the user is accepting these conditions. Download BelowR1CGCustomFW_0.95_2015-12-28.tar.gzUpgrade instructionsTo upgrade your firmware, go to "Backup / Flash Firmware" under the "System" tab
- Click on the "Chose File" button to the right of "Restore Backup:" (NOTE: Do not mistake this with the "Chose File" button under Flash new firmware. - This is not a full binary firmware file)
- Choose "R1CGCustomFW_0.95_2015-12-28.tar.gz" from your PC and then click on the "Upload archive" button.
Your antrouter system will reboot and come back up with updated firmware!
Rockminer RBox Rev 2Update 9/12/2014: Windows installation package now includes new cgminer build for Windows that supports the second gen R-Box and frequencies up to 350
Download Windows Installation PackagePackage is available in English, French, Spanish, Chinese(HK) and Chinese(Traditional)
Rockminer Rbox Rev 1Package Instructions for Running on Windows:1) Download CGMiner installation msi for your corresponding language:
-
Download Windows Installation Package2) Run installation Package
3) Run zadig_xp_2.1.0.exe from the dektop or start menu
4) Select your device in the top drop down (CP2102 USB to UART Bridge Controller) and select WinUSB in the bottom drop down
5) Click "Install Driver"
6) Close Zadig
7) Run "Start Cgminer" from desktop or start menu
BTCGarden AMV1X2If you are purchasing a BTCGarden AMV1X2 miner without an RPi, please note that it will not come with an RPi data cable. Fortunately, it's very easy to make one from the extra daisy chain cable provided.
The RPi data cable and standard data cable are exactly the same, except for the location of 2 pins. To convert a standard data cable to an RPi data cable, remove the bottom right 2 pins, wrap them in electrical tape or heatshrink tubing, and connect to the RPi like so:
To remove the two pins, place a small point under the black tabs which hold the pins in. Lift up as you slide the pins out.
Rockminer RBox Rev 1Update 6/4/2014: Windows installation package now includes new cgminer build for Windows that fixes freq settingDownload Windows Installation PackagePackage is available in English, French, Spanish, Chinese(HK) and Chinese(Traditional)
Package Instructions for Running on Windows:1) Download CGMiner installation msi for your corresponding language:
-
Download Windows Installation Package2) Run installation Package
3) Run zadig_xp_2.1.0.exe from the dektop or start menu
4) Select your device in the top drop down (CP2102 USB to UART Bridge Controller) and select WinUSB in the bottom drop down
5) Click "Install Driver"
6) Close Zadig
7) Run "Start Cgminer" from desktop or start menu
Manual Instructions for Running on Windows:1) Download "cgminer-win0.3.1.zip" from the following location:
-
https://github.com/rockminerinc/cgminer-for-R-BOX2) Extract and plug in your r-box
3) Run zadig_xp_2.1.0.exe from the cgminer-win0.3.1 directory
4) Select your device in the top drop down (CP2102 USB to UART Bridge Controller) and select WinUSB in the bottom drop down
5) Click "Install Driver"
6) Close Zadig and open cgminer-win0.3.1\cg.cmd in notepad
7) If you want to mine with eligius, just change the bitcoin payout address.
8) Optionally, you can add "--anu-freq XXX" as a parameter for overclocking. Replace XXX with current valid clock values of 270-290
Instructions for Running on Linux:1) Download cgminer 4.3.3 from git or other repository
2) Replace cgminer.c, driver-Icarus.c and miner.h with files from this location:
-
https://github.com/rockminerinc/cgminer-for-R-BOX3) Compile and run cgminer
4) Optionally, you can add "--anu-freq XXX" as a parameter for overclocking. Replace XXX with current valid clock values of 270-290
Rockminer Provided Image For Raspberry PiRaspberry Pi ImageRPi Image HandbookHow to add dhcp and wifi compatibility to your raspberry pi image (Tested with $9 edimax wifi adapter):
1) Plug in Ethernet cord and SSH into your raspberry pi
2) Run the following command to open the network interface config in nano (or use vim if you are a bit nerdier)
sudo nano /etc/network/interfaces
3) Modify the contents of the file as follows(ctrl-x then Y to save):
auto lo
iface lo inet loopback
iface eth0 inet dhcp
auto wlan0
allow-hotplug wlan0
iface wlan0 inet dhcp
wpa-ssid "YOUR_WIFI_SSID_HERE"
wpa-psk "YOUR_WIFI_WPA_PASSWORD_HERE"
4) Power off your pi
5) Remove ethernet cord
6) Start Raspberry pi and use your router config or an application like angryip to scan for the RPi's new address.
Show Posts
