cgminer version 4.2.2 - Started: [2014-04-10 09:52:26] -------------------------------------------------------------------------------- (5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s A:0 R:0 HW:0 WU:0.0/m Connected to "pool" diff 8 with stratum as user "user" Block: 9ffe96f9... Diff:73.4K Started: [09:52:35] Best share: 0 -------------------------------------------------------------------------------- SB management [P]ool management ettings [D]isplay options [Q]uit -------------------------------------------------------------------------------- [2014-04-10 09:52:24] Started cgminer 4.2.2 [2014-04-10 09:52:24] Loaded configuration file /root/.cgminer/cgminer.conf [2014-04-10 09:52:25] No devices detected! [2014-04-10 09:52:25] Waiting for USB hotplug devices or press q to quit [2014-04-10 09:52:25] Probing for an alive pool [2014-04-10 09:52:26] Pool 0 difficulty changed to 8 [2014-04-10 09:52:26] Network diff set to 73.5K [2014-04-10 09:52:31] API bind to port 4028 failed - trying again in 30sec [2014-04-10 09:52:35] Network diff set to 73.4K [2014-04-10 09:52:35] Stratum from pool 0 detected new block
As HellDiverUK said, there is other cgminer run in your host, maybe you just not know how to see it. I test this already & the message is same. Check your pool, your worker must be submitting share this whole time LOL.
|
|
|
Hashrate will be differ based on hardware, so had variant is normal. It's not the software fault
|
|
|
i dont think i can find tplink in a store near where i live. a new raspberry pi should work so installing os and miner shouldnt be a problem.
Then in mean time try to reinstall the linux
|
|
|
its just that with shipping costs you almost pay twice the value for the product. i thought of a raspberry pi, it costs more but it is more powerfull and you can use it the same way as a computer. And i will have it before the tplink would have arrived.
You can buy tplink from local store behind the corner much more chipper than Pi. And flash it Tplink can handle a lot even though it seems less powerful compared to PI Let say 10 HEx8 - 2.1T in total without issues - personal experience. So do not worry And with Rpi you still need to install the OS, then compile the cgminer. With TPLINK you only need to flash with latest firmware from technobit & ready to go.
|
|
|
I guess your linux system already contaminated. Times to move on & buy TPLINK TL-MR3020
|
|
|
Bus 001 Device 002: ID 5986:0241 Acer, Inc BisonCam, NB Pro Bus 003 Device 005: ID 04d8:000a Microchip Technology, Inc. CDC RS-232 Emulation Demo Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 005: ID 04d8:000a Microchip Technology, Inc. CDC RS-232 Emulation Demo, this is your miner. But it's located on usb 1 root. Try to moved it to usb 2 root.
|
|
|
type following command on terminal: Post each output from that command.
|
|
|
Here we are working @ 110 GHs with 2.5 % HW Wow, that was great marto. 6,875 GH/s per chip.
|
|
|
I apologise for my English not good.I installed cgminer and the usb drivers but the miner is recognized on cgminer and stays at 0 GH/S with default settings.Used computer HARDWARE intel i3 with installed windows 7 32 bit and direct connection via usb with miner HEX8A1. psu corsair AX760i
Ok, the hardware is good. Then which cgminer version did you use & where you get from?
|
|
|
i tried to delete it by right-clicking and move to trash since i dont know that many commands
sudo rm -rf /home/b/.cgminer/cgminer.conf
|
|
|
sudo ./cgminer?
i did that.
i mean add sudo when deleting conf file. You don't need to delete cgminer folder since conf located in other location.
|
|
|
i removed the cgminer-4.2.2 folder and started all over with this then i started up cgminer .... (now there is 2 cgminer.conf files one with "pool" on the image and one with "..." and i can not delete any of them) [2014-04-10 08:59:39] Started cgminer 4.2.2 [2014-04-10 08:59:39] Loaded configuration file /root/.cgminer/cgminer.conf [2014-04-10 08:59:40] No devices detected! [2014-04-10 08:59:40] Waiting for USB hotplug devices or press q to quit [2014-04-10 08:59:40] Probing for an alive pool [2014-04-10 08:59:40] Pool 0 difficulty changed to 8 [2014-04-10 08:59:41] Network diff set to 73.4K [2014-04-10 08:59:46] API bind to port 4028 failed - trying again in 30sec
add sudo on your command
|
|
|
conf file { "pools" : [ { "url" : "url", "user" : "user", "pass" : "pass" } ] , "api-listen" : true, "api-allow" : "R:127.0.0.1", "api-mcast-port" : "4028", "api-port" : "4028", "expiry" : "120", "hotplug" : "5", "log" : "5", "no-pool-disable" : true, "queue" : "1", "scan-time" : "60", "shares" : "0", "hexminera-voltage" : "1460", "hexminera-options" : "16:480", "hexminerc-voltage" : "1100", "hexminerc-options" : "16:1500", "hexminerb-voltage" : "900", "hexminerb-options" : "16:540", "hexminer8-set-diff-to-one" : "0", "hexminer8-chip-mask" : "255", "hexminer8-voltage" : "1000", "hexminer8-options" : "8:260", "hexmineru-frequency" : "54", "set_default_to_8" : true, "kernel-path" : "/usr/local/bin" } I did't see anything wrong with the conf. So you need to delete existing conf file & ask cgminer to generate new conf file.
|
|
|
[2014-04-09 15:44:13] Started cgminer 4.2.2 [2014-04-09 15:44:13] Loaded configuration file /home/b/.cgminer/cgminer.conf [2014-04-09 15:44:13] Fatal JSON error in configuration file. [2014-04-09 15:44:13] Configuration file could not be used. [2014-04-09 15:44:14] No devices detected! [2014-04-09 15:44:14] Waiting for USB hotplug devices or press q to quit [2014-04-09 15:44:14] Need to specify at least one pool server. There must be some missing of comma or apostrope on your conf.
|
|
|
Your explanation is null dude. I take that english is not your main language. You can ask for help on this thread yet you didn't. You need to tell us you hardware specs, PSU capacity, HUB, & shot some picture. If you insist on windows, you will had headache since no working cgminer 1 month ago but recently 2GOOD had posting working cgminer with technobit support. Best course is to use TPLINK TL-MR3020 as host.
|
|
|
Hey, Disable sysntpd after upgrade that is the problem /etc/init.d/sysntpd disable reboot If it is not tplink just disable it ntpd Woo, just find out that using sysupgrade.bin, some process that supposed to disable is enable. Thanks loshia for tplink after upgrade type /usr/bin/fix_rc & exit that will disable the junk and reboot router Nice I almost reflash using factory.bin , lucky Thanks loshia
|
|
|
Hey, Disable sysntpd after upgrade that is the problem /etc/init.d/sysntpd disable reboot If it is not tplink just disable it ntpd Woo, just find out that using sysupgrade.bin, some process that supposed to disable is enable. Thanks loshia
|
|
|
World fastest USB stick miner
|
|
|
|