Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[muzuca]

Wait for claymore until he releases new algos for new coins.....

When it's can be released?
I have unusual situation: my PSU made much noise in ETH mode only. So, I have to continue with dual mining in order to reduce the noise. Stupid situation, but can't do nothing. 

Strange situation at all, probably for some reason in ETH mode your setup is consuming more power from PSU. I tried with my rigs and the only way to do that is when I’m using stock config of my GPUs and the power consumption is higher.

[Lamsterpaul]

Is there an solution, so that wattman will not reset the settings ?
I have not overclocked, some cards will set at a less gpu clock, to keep the temp lower,
But sometime wattman crashes and reset all and then overheats my room :-)
minersoftware will not crash only wattmann,

There is also a new AMD driver available 18.2.1, hope it is better,
Got 2 rigs with 12 AMD R9 390 and the consume much and also produce much heat

[Victorio]

hi folks,
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2,  16.10.3  15.12,  18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup

1. You are risking to brick the GPU by flashing a downloaded BIOS image. Just move the 1500 or custom timing to 1750 to 2000 straps and overclock manually by MSI Afterburner or OverDriveNTool.
2. How many GPUs do you have and what's your MOBO? If 4+ GPUs, have you enabled Above 4G Decoding/Mining Mode? Above 4G Decoding works only in UEFI environment<>Windows installation must be UEFI as well.
3. You were getting low hashrate because none of 15.x-16.x drivers have the DAG fix (you are attempting to mine ETH or ETC, performance of both affected by DAG size) and the DAG fix was not activated in 18.2. I'd go with AMD 17.12.1 driver, it seems stable and enable Compute Workload for all GPUs (AMD Preferences>Settings>General>Gaming>select Compute Workload).

[Victorio]

I have unusual situation: my PSU made much noise in ETH mode only. So, I have to continue with dual mining in order to reduce the noise. Stupid situation, but can't do nothing. 

Strange situation at all, probably for some reason in ETH mode your setup is consuming more power from PSU. I tried with my rigs and the only way to do that is when I’m using stock config of my GPUs and the power consumption is higher.
[/quote]
He did not specify what kind of noise his PSU emits - is it fan noise or coil whine. Coil whine can actually be much more audible at lower power load.

[Amstellodamois]

RX 580 8G, Hynix memory (2225 MHz IIRC). I'm pretty happy with the speed, yeah. I reach 31.6 MH/s per card with a clock of 2250 MHz but shit happens from time to time (although my memory errors appear to be very very very low).

Care to share your config file (memory and core speeds and voltages) ?
What's your per gpu consumption?

1200 & 2225 MHz
900 mV for everything
Power consumption between 850 and 950 W for the whole rig (6 cards)

[cryptor47]

I finally have a stable system with a good hashrate.
Any ideas to make it even better? With more hashrate or the same with lower temps?

GPU0 (Bios from https://anorak.tech)
Gigabyte RX 570 Gaming
Core 1190
Memory 2110

GPU1 (Bios from https://anorak.tech)
Gigabyte RX 570 Aurus
Core 1210
Memory 2080

GPU2
Palit 1070 JetStream
Power Limit 70
Core -200
Memory +780

[manotroll]

anyone who dual mining could share the command line they use?

[manoe]

hi folks,
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2,  16.10.3  15.12,  18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup

1. You are risking to brick the GPU by flashing a downloaded BIOS image. Just move the 1500 or custom timing to 1750 to 2000 straps and overclock manually by MSI Afterburner or OverDriveNTool.
2. How many GPUs do you have and what's your MOBO? If 4+ GPUs, have you enabled Above 4G Decoding/Mining Mode? Above 4G Decoding works only in UEFI environment<>Windows installation must be UEFI as well.
3. You were getting low hashrate because none of 15.x-16.x drivers have the DAG fix (you are attempting to mine ETH or ETC, performance of both affected by DAG size) and the DAG fix was not activated in 18.2. I'd go with AMD 17.12.1 driver, it seems stable and enable Compute Workload for all GPUs (AMD Preferences>Settings>General>Gaming>select Compute Workload).

thanks for the reply's,
for the moment i'm installing windows 10 again,
The MOBO is an R2.0 pro btc asrock and i'm trying out 4 gpu 's
what would you mean with enable 4G decoding/mining mode?
when the windows is installed i'm already going to give it a try with the 17.12.1 driver, the timing straps should normaly be already set from 1500 to the 2000, going to try out the clock at 1150 cclock, 2100 mclock, 950 mvddc.

[Victorio]

for the moment i'm installing windows 10 again,
The MOBO is an R2.0 pro btc asrock and i'm trying out 4 gpu 's
what would you mean with enable 4G decoding/mining mode?
when the windows is installed i'm already going to give it a try with the 17.12.1 driver, the timing straps should normaly be already set from 1500 to the 2000, going to try out the clock at 1150 cclock, 2100 mclock, 950 mvddc.

ASRock H81 Pro BTC doesn't have the 4G decoding option, you can skip it.
Start with 1950-2000 memory clock and 900-925 memory voltage, add gradually memclock and decrease voltage, checking memory errors through HWInfo64.

[kkourmousis]

1200 & 2225 MHz
900 mV for everything
Power consumption between 850 and 950 W for the whole rig (6 cards)

Thanks. Yep I had that numbers back in June (when I was on solo mining) but I pay a lot for electricity so power consumption is a major issue for me.

My 580s average is 29.5, but they consume 135w each (1150 and 2080-2250, 850mv for everything)


Thanks for sharing. Btw, what cards do you have? Mine are Sapphire Nitro+ 580 8GB (Hynix).

[manoe]

ASRock H81 Pro BTC doesn't have the 4G decoding option, you can skip it.
Start with 1950-2000 memory clock and 900-925 memory voltage, add gradually memclock and decrease voltage, checking memory errors through HWInfo64.

ok thanks, will give it a try

[marcusa007]

I am fairly new at this and have been reading a lot to get up to speed. I have my first rig set up with two RX580 Red Dragon cards (needless to say I should have bought 3 since my plan was to build a trio).
I have the system running pretty smooth with smOS. I am dual mining Ethereum and Sia. One of the cards is not performing as well as the other. Purchased from the same retailer the same day. Probably doesn't mean anything and could still be different chipsets.

Here is what I am currently getting:
ETH - Total Speed: 56.308 Mh/s, Total Shares: 1141, Rejected: 0, Time: 11:18
ETH: GPU0 26.916 Mh/s, GPU1 29.392 Mh/s
SC - Total Speed: 1126.154 Mh/s, Total Shares: 321, Rejected: 0
SC: GPU0 538.314 Mh/s, GPU1 587.840 Mh/s
GPU0 t=64C fan=60%%, GPU1 t=58C fan=47%%

I have it set to:
Core: 1200
Memory: 2200
Undervolting: 950
Powerstage: 2

I have played around with these settings but can't seem to get it to be higher on GPU0.

Anyone have an Idea or is this the best I am going to get?

Thanks.

Mining dual sia is a waste of energy now. With your setup you get 1 or 2 SC a day (maybe 5 cents). What's your speed with solo ETH mining?

I played around with it a bit and a little higher numbers and the small fluctuations in Mh/s I had are almost none existent.

ETH - Total Speed: 56.873 Mh/s, Total Shares: 20, Rejected: 0, Time: 00:13
ETH: GPU0 27.340 Mh/s, GPU1 29.533 Mh/s
ETH - Total Speed: 56.872 Mh/s, Total Shares: 20, Rejected: 0, Time: 00:13
ETH: GPU0 27.336 Mh/s, GPU1 29.536 Mh/s
GPU0 t=63C fan=47%%, GPU1 t=52C fan=47%%
ETH - Total Speed: 56.836 Mh/s, Total Shares: 20, Rejected: 0, Time: 00:13
ETH: GPU0 27.305 Mh/s, GPU1 29.531 Mh/s
GPU0 t=63C fan=47%%, GPU1 t=52C fan=47%%
ETH - Total Speed: 56.855 Mh/s, Total Shares: 20, Rejected: 0, Time: 00:13
ETH: GPU0 27.323 Mh/s, GPU1 29.531 Mh/s

I have it now set to:
Core: 1200
Memory: 2250,2225
Undervolting: 900
Powerstage: 2

GPU0 still is much lower. Anyone any idea of settings I could use to make that one faster?

Thanks.

[Digital Drug Lord]

I have 2 nvida video cards, say I wanted to use one to edit video and one to mine, what would the code look like? I couldnt find it in the readme

[ollis miner]

I have 2 nvida video cards, say I wanted to use one to edit video and one to mine, what would the code look like? I couldnt find it in the readme

read the Readme file once more

Use -di to select GPU's to mine with

EthDcrMiner64.exe -epool eu1.nanopool.org:9999 -ewal 0xd69af2a796a737a103f12d2f0bcc563a13900e6f -epsw x -eworker rig1 -di 1 (to use GPU #1 for mining)

[groovytechno]

I have 2 nvida video cards, say I wanted to use one to edit video and one to mine, what would the code look like? I couldnt find it in the readme

Or manually disable a gpu while mining by pressing "0", for example.

[dortortz]

Hi Admin,
Is there any chance that GPU wattage can be added to the miner's API for remote monitoring purposes? I hope that maybe its already in the plans.
Would be greatly appreciated

[goodbitprofit]

anyone who dual mining could share the command line they use?

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal MYWALLET.MYRIGNAME/MYEMAIL -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal MYWALLET.MYRIGNAME/MYEMAIL -dpsw x -dcri 10 -etht 1000 -mport 0 -mode 0 -r 1 -tt 68 -allpools 1 -tstop 75

[goodbitprofit]

1200 & 2225 MHz
900 mV for everything
Power consumption between 850 and 950 W for the whole rig (6 cards)

Thanks. Yep I had that numbers back in June (when I was on solo mining) but I pay a lot for electricity so power consumption is a major issue for me.

My 580s average is 29.5, but they consume 135w each (1150 and 2080-2250, 850mv for everything)


Thanks for sharing. Btw, what cards do you have? Mine are Sapphire Nitro+ 580 8GB (Hynix).

I had also problems with my rig and MB Gigabyte H110, 3 cards are Hynix and 3 cards are Samsung memori. Purchased in same store but on other location. After several attempts to set up rig, finally finish with settings and now working smooth :
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal MYWALLET.MYRIGNAME/MYEMAIL -epsw x -dcoin pasc -dpool pasc-eu1.nanopool.org:15555 -dwal MYWALLET.MYRIGNAME/MYEMAIL -dpsw x -dcri 10 -etht 1000 -mport 0 -mode 0 -r 1 -cclock 1200,1150,1200,1200,1200,1200 -mclock 2250,2050,2030,2200,2230,2050 -powlim 20,20,20,20,20,20 -cvddc 900,900,900,900,900,900 -mvddc 900,900,900,900,900,900 -tt 68 -allpools 1 -tstop 75

Still have some problems with GPU 0 that sometimes just give 20MH/s and then just jump to 29-30MH/s, but I just give up.I am satisfied, no more restarts every hour or two, and once per week my Win10 just freeze.
Drivers are from Aug23, blockchain, and Claymore is 10.2

[Maniac9331]

Hello

i recently switched all my GTX 1070/1070ti to ETH due to ZEC price drops etc.
I find some rigs work ok (stable) and on some the hashrate is fluctuating.

may this be realted to drivers? are there drivers ok ?

385.41 for 6x1070 rigs

and 388.59 fo 6x1070ti rigs? or claymore requires the newest nvidia drivers?

i use v10.5 version.... the HASHRATE is ok at the start, but then after some time fluctuates. I check on nanopool for 6hr average and find some rigs only have 170 MH/s avg.

settings differ cause i try...

1070: power 75 (high but i want stability, not really low power), core -200 (some -190 now), mem +680 (some +690). the rigs are very cool temps around 38-42 deg.

i put -r 120 so the client restarts (i find this give better hash?)

MY RX580 rigs are 100% stable there is no fluctiation but nvidia with ETH gives me headache plz help ;-)



ETH: 02/03/18-13:29:46 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 191.148 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:22
ETH: GPU0 31.876 Mh/s, GPU1 31.869 Mh/s, GPU2 31.899 Mh/s, GPU3 31.850 Mh/s, GPU4 31.756 Mh/s, GPU5 31.900 Mh/s
ETH: 02/03/18-13:30:11 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 184.847 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:22
ETH: GPU0 31.192 Mh/s, GPU1 29.779 Mh/s, GPU2 31.177 Mh/s, GPU3 30.376 Mh/s, GPU4 31.250 Mh/s, GPU5 31.073 Mh/s
GPU0 t=39C fan=69%, GPU1 t=42C fan=69%, GPU2 t=41C fan=69%, GPU3 t=38C fan=69%, GPU4 t=32C fan=69%, GPU5 t=48C fan=69%
ETH: 02/03/18-13:30:27 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 174.012 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 23.557 Mh/s, GPU1 30.301 Mh/s, GPU2 30.699 Mh/s, GPU3 30.942 Mh/s, GPU4 30.857 Mh/s, GPU5 27.655 Mh/s
ETH: 02/03/18-13:30:35 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 146.193 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 22.078 Mh/s, GPU1 22.095 Mh/s, GPU2 31.022 Mh/s, GPU3 22.006 Mh/s, GPU4 26.825 Mh/s, GPU5 22.167 Mh/s
ETH: 02/03/18-13:30:43 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 189.880 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.674 Mh/s, GPU1 31.843 Mh/s, GPU2 31.833 Mh/s, GPU3 31.756 Mh/s, GPU4 31.142 Mh/s, GPU5 31.633 Mh/s
GPU0 t=39C fan=69%, GPU1 t=43C fan=69%, GPU2 t=43C fan=69%, GPU3 t=38C fan=69%, GPU4 t=32C fan=69%, GPU5 t=48C fan=69%
ETH: 02/03/18-13:30:50 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 191.070 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.879 Mh/s, GPU1 31.858 Mh/s, GPU2 31.790 Mh/s, GPU3 31.868 Mh/s, GPU4 31.859 Mh/s, GPU5 31.816 Mh/s
ETH: 02/03/18-13:30:51 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 190.558 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.838 Mh/s, GPU1 31.822 Mh/s, GPU2 31.588 Mh/s, GPU3 31.853 Mh/s, GPU4 31.816 Mh/s, GPU5 31.641 Mh/s
ETH: 02/03/18-13:31:12 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 189.109 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.362 Mh/s, GPU1 31.209 Mh/s, GPU2 31.028 Mh/s, GPU3 31.851 Mh/s, GPU4 31.836 Mh/s, GPU5 31.823 Mh/s

Try this on 1070: power 63 core -200 , clock 740 rock solid 6 1070"s  192 total Mh/s

[diviak]

Hi all.
I have win10 64bit,claymore v10,06 , motherboard asus v7 exp., 8gb ram,one asus strix gtx970 4gb oc. When I turn on claymore i have only 2,699 Mh/s. I am using ethermine.org. Is the graphics card so bat or badly set up? I downloaded 352.xx beta driver old but stil the same. PLS help thx

any help for me?