Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[Claymore]

Dear Claymore when are you going to realase 6.5v ? I have to upgrade some rigs and I wonder if to upgrade to 6.4 or to wait few days..

I'm going to release v7.0 Beta within 24 hours. Doing last tests, may be in a few hours.

This morning i found my rig stopped and when i started it win 7 x64, none of the 6 r9 380 card was detected in device manager. I tested 1 card on another pc and it works, but i saw a message saying with red that i never saw before: 1 share rejected gpu 1 (the test one) if u overclocked it too much etc
The log looks suspicious.

It is hardware problem, if you see 511C temp check your risers/clocks.

[Claymore]

v7.0 Beta:

- added new coin for dual mode: LBRY(LBC). Now you can mine Ethereum, Ethereum+Decred, Ethereum+Siacoin or Ethereum+Lbry.
- some minor improvements and bug fixes.

[Trimegistus]

v7.0 Beta:

- added new coin for dual mode: LBRY(LBC). Now you can mine Ethereum, Ethereum+Decred, Ethereum+Siacoin or Ethereum+Lbry.
- some minor improvements and bug fixes.

Great news!

Thanks!

[alevlaslo]

Thanks!

But so less LBC if dcri 500, only 400 mh on my farm that get 935 mh by Wolf privat miner

[orionpaxx12]

I'm mining with NVIDIA 1070 using the recommended driver on first page (anniversary update) for win10 64BIT.  but I'm only get 3.5MH for ETH.  What is going on? This is for MSI 1070 and Asus 1070.  4 different cards tested separately.

Prolly your system problem, go and run dxdiag check if display is with WDDM 2.1 support, it should be for win10 for mining ethereum

Also reinstall driver and check do a clean install

For 1070 with samsung memory ~33mhs is duable if 2350mhz clock is stable, the one with micron clock a lot less and they don`t go over ~28mhs

quick question please how do you tell what kind of memory it has like samsung or something else

[Claymore]

Thanks!

But so less LBC if dcri 500, only 400 mh on my farm that get 935 mh by Wolf privat miner

1. I rescaled -dcri for LBC so you cannot use miner for LBC only.
2. LBC is not so good for dual mode as DCR or SIA.

About private miner - I don't have it so don't know how fast it is, but in my tests I was able to get 200MH/s on LBC for stock 390X. Unfortunately, there is no way to use same code in dual mode, I had to write different code that is slower, it shows only 165MH/s on stock 390X.

[alevlaslo]

290x get 180 by Wolf

LBC only miner more profitable than dual

[Claymore]

290x get 180 by Wolf

LBC only miner more profitable than dual

Well, use private miner for now if you have it, may be situation will change in future.

[xeridea]

I'm mining with NVIDIA 1070 using the recommended driver on first page (anniversary update) for win10 64BIT.  but I'm only get 3.5MH for ETH.  What is going on? This is for MSI 1070 and Asus 1070.  4 different cards tested separately.

Prolly your system problem, go and run dxdiag check if display is with WDDM 2.1 support, it should be for win10 for mining ethereum

Also reinstall driver and check do a clean install

For 1070 with samsung memory ~33mhs is duable if 2350mhz clock is stable, the one with micron clock a lot less and they don`t go over ~28mhs

quick question please how do you tell what kind of memory it has like samsung or something else

GPU-Z

[antantti]

About private miner - I don't have it so don't know how fast it is, but in my tests I was able to get 200MH/s on LBC for stock 390X. Unfortunately, there is no way to use same code in dual mode, I had to write different code that is slower, it shows only 165MH/s on stock 390X.

Are you going to release LBC only miner?

[lttsi]

Can't work with 1060 dual ETH+LBC ,i got a stop driver (no overlock ).

[reb0rn21]

I'm mining with NVIDIA 1070 using the recommended driver on first page (anniversary update) for win10 64BIT.  but I'm only get 3.5MH for ETH.  What is going on? This is for MSI 1070 and Asus 1070.  4 different cards tested separately.

Prolly your system problem, go and run dxdiag check if display is with WDDM 2.1 support, it should be for win10 for mining ethereum

Also reinstall driver and check do a clean install

For 1070 with samsung memory ~33mhs is duable if 2350mhz clock is stable, the one with micron clock a lot less and they don`t go over ~28mhs

quick question please how do you tell what kind of memory it has like samsung or something else

Use GPU-z, on first screen by the memory type you will see:
Samsung  --- GOOD!
Micron ---- BAD!

Also lbry is slow on AMD clay, use private miner if you wana LBC

[xeridea]

Testing so far, LBRY impacts Eth a bit more, lose ~1-2MH with -dcri 40.  Getting about 40MH LBRY on RX 470/480.  It does use ~15-20W less power per card though.  With current difficulty, it is slightly more profitable than Sia.  I would get ~90MH on ccMiner, if I set -dcri really high, this outperforms ccMiner.

Mining on 1060 or 970 is abysmal, ~20Mh, get ~140+ on ccMiner.  Win7, latest drivers.  Maybe it's just me?

Great work!  Hopefully LBRY can be fine tuned just a bit.

[Claymore]

About private miner - I don't have it so don't know how fast it is, but in my tests I was able to get 200MH/s on LBC for stock 390X. Unfortunately, there is no way to use same code in dual mode, I had to write different code that is slower, it shows only 165MH/s on stock 390X.

Are you going to release LBC only miner?

I have only OpenCL-related code, a lot of work is required to create separate miner for LBC, I just don't have time for it. I can put it in dual miner as separate mode but not sure if it worth doing it since there is some private miner with same speed. So I think the answer is no.

[wlefever]

Getting 136-138 MH/s LBC and 94-96 MH/s ETH on 4 reference 480's using about 655 watts. I am happy with it!

[joniosbra]

5 x 1070 EVGA SC (default clocks)
Windows 10 Anniversary Update
Nvidia driver: 372.54

ETH 24.8/card
LBC 23.7/card

[Ragnarokdel]

would be nice to get a stable version for newer amd drivers... 15.12 is mega-old now. We're talking december 2015.

[Xdragon]

5 x 1070 EVGA SC (default clocks)
Windows 10 Anniversary Update
Nvidia driver: 372.54

ETH 24.8/card
LBC 23.7/card

One more win for Polaris over Pascal 

[ioglnx]

Could you also add the option to only mine LBRY?

Is it normal that it shows DCR instead of LBRy when mining?

TH - Total Speed: 20.859 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 20.859 Mh/s
 DCR - Total Speed: 208.591 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 208.591 Mh/s

Mined against lbry.suprnova.cc

[fittsy]

Could you also add the option to only mine LBRY?

Is it normal that it shows DCR instead of LBRy when mining?

TH - Total Speed: 20.859 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 20.859 Mh/s
 DCR - Total Speed: 208.591 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 208.591 Mh/s

Mined against lbry.suprnova.cc

You forgot to set

Code:

-dcoin lbc

He also mentioned it is not currently possible to do library only. See this response (last post, previous page)
https://bitcointalk.org/index.php?topic=1433925.msg16177469#msg16177469