alexmobile
Newbie
 Offline
Activity: 12
Merit: 0
|
 |
August 14, 2016, 03:40:05 AM |
|
Good morning Couldn't get Claymore to function figured it maybe the pools I chose my start.bat file is as follows but I am getting errors like crazy. Hopefully someone has some ideas I am at a Loss GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe -epool eth-us-east1.nanopool.org:9999 -ewal 0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB -epsw x #-esm 0 -estale 0 -dpool http://dcr.maxminers.net:7728-dwal alexmobile.alexmobile -dpsw 0311 -mode 0 -tt 80 Errors I am receiving... ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00 23:24:19:108 d04 ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s 23:24:19:109 d04 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0 23:24:19:111 d04 DCR: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s Setting DAG epoch #68 for GPU #0 23:24:21:169 c1c Create GPU buffer for GPU #0 23:24:21:171 c1c OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions. 23:24:21:172 d1c Setting DAG epoch #68 for GPU #3 23:24:21:174 d1c Create GPU buffer for GPU #3 23:24:21:177 d1c OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions. 23:24:21:178 538 Setting DAG epoch #68 for GPU #2 23:24:21:181 538 Create GPU buffer for GPU #2 23:24:21:183 538 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions. 23:24:21:186 cfc Setting DAG epoch #68 for GPU #1 23:24:21:187 cfc Create GPU buffer for GPU #1 and this as well DCR job updated 23:24:24:175 b84 Setting DAG epoch #68 for GPU #0 23:24:24:181 b84 GPU 0, OpenCL error -38 - cannot write buffer for DAG 23:24:24:186 d74 Setting DAG epoch #68 for GPU #3 23:24:24:192 d74 GPU 3, OpenCL error -38 - cannot write buffer for DAG 23:24:24:198 e68 Setting DAG epoch #68 for GPU #2 23:24:24:203 e68 GPU 2, OpenCL error -38 - cannot write buffer for DAG 23:24:24:207 3d0 Setting DAG epoch #68 for GPU #1 23:24:24:211 3d0 GPU 1, OpenCL error -38 - cannot write buffer for DAG |
|
|
|
|
|
|
|
The forum strives to allow free discussion of any ideas. All policies are built around this principle. This doesn't mean you can post garbage, though: posts should actually contain ideas, and these ideas should be argued reasonably.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
pwpwpw
|
 |
August 14, 2016, 03:59:00 AM |
|
set pagefile to 16gb, remove # from esm line and have more than 2gb gpu's. so this is your start.bat GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe and this your config.txt -epool eth-us-east1.nanopool.org:9999 -ewal 0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB -epsw x -esm 0 -estale 0 -dpool http://dcr.maxminers.net:7728-dwal alexmobile.alexmobile -dpsw 0311 -mode 0 -tt 80 if dcr doesn't start, change esm values, from 0 to 3, see which is good for that pool |
|
|
|
alexmobile
Newbie
Offline
Activity: 12
Merit: 0
|
|
August 14, 2016, 04:13:55 AM
Last edit: August 14, 2016, 07:51:38 AM by alexmobile |
|
Thanks for the help...but still does not work I have no problems using NiceHash's GUI software I usually get 54.7mh/s... wanted to try to use Claymore and focus on Eth for myself. Reconfigured both the Start and config files, already have pagefile more than 16gb. I tried both ways on the esm 0 and 3 still get these errors 00:09:18:804 e44 args: -epool eth-us-east1.nanopool.org:9999 -ewal 0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB -epsw x -esm 0 -estale 0 -dpool http://dcr.maxminers.net:7728 -dwal alexmobile.alexmobile -dpsw 0311 -mode 0 -tt 80
00:09:18:805 e44
00:09:18:806 e44 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
00:09:18:806 e44 º Claymore's Dual ETH + DCR/SC AMD GPU Miner v5.3 Beta º
00:09:18:807 e44 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
00:09:18:807 e44
00:09:19:007 e44 ETH: 1 pool is specified
00:09:19:008 e44 Main Ethereum pool is eth-us-east1.nanopool.org:9999
00:09:19:009 e44 DCR: 1 pool is specified
00:09:19:009 e44 Main Decred pool is dcr.maxminers.net:7728
00:09:20:775 e44 OpenCL platform: AMD Accelerated Parallel Processing
00:09:20:776 e44
Cards available: 4
00:09:20:776 e44 GPU #0: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:776 e44 GPU #1: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #2: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #3: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 Total cards: 4
00:09:20:777 e44 Initializing...
00:09:20:777 e44 GPU #0 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #1 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #2 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #3 recognized as Radeon 270/270X
00:09:20:778 e44 POOL/SOLO version
00:09:20:778 e44 b176
00:09:20:804 e44 start building OpenCL program...
00:09:39:262 e44 done
00:09:39:263 e44 GPU #0: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #1: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #2: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #3: set -etha as 1 (ETH algo for slow cards)
00:09:39:424 b20 ETH: Stratum - connecting to 'eth-us-east1.nanopool.org' <45.55.155.113> port 9999
00:09:39:455 e44 DUAL MINING MODE ENABLED: ETHEREUM+DECRED
00:09:39:455 e44 ETH: eth-proxy stratum mode
00:09:39:455 e44 Watchdog enabled
00:09:39:455 e44 Remote management is enabled on port 3333
00:09:39:456 e44
00:09:39:456 3d0 DCR - connecting to dcr.maxminers.net:7728
00:09:39:456 3d0 http send request: {"method": "getwork", "params": [], "id":0}
00:09:39:466 b20 send: {"worker": "eth1.0", "jsonrpc": "2.0", "params": ["0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB", "x"], "id": 2, "method": "eth_submitLogin"}
00:09:39:466 b20 ETH: Stratum - Connected (eth-us-east1.nanopool.org:9999)
00:09:39:567 3d0 http got answer: {"result":{"data":"01000000f4af4e4667548b12a3c5487c7346b7b92cd1708fcfd7045603130000000000008ff1e94757cd23ff3a88e4f78d0eaad794ae07bfaa7cda0e06f9300d13d920b06fe6b82325e861de5f7f5a7411f42b52145c9d10114f5661ecf1e24b677d239b0100af8114c798db0500000090a300009f62141a8aec30e70000000037d400006e0f000029efaf57000000000000000000000000000000000000000000000000000000000000000000000000000000008000000100000000000005a0","target":"ffffffffffffffffffffffffffffffffffffffffffffffffffffff3f00000000"},"id":0,"error":null}
00:09:39:567 3d0 DCR: Connected (dcr.maxminers.net:7728)
00:09:39:567 3d0 DCR job updated
00:09:39:687 b20 got 282 bytes
00:09:39:687 b20 buf: {"jsonrpc":"2.0","id":2,"result":true}
{"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:687 b20 parse packet: 38
00:09:39:687 b20 ETH: Authorized
00:09:39:688 b20 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}
00:09:39:688 b20 remove first packet 243
00:09:39:688 b20 new buf size: 243
00:09:39:688 b20 parse packet: 242
00:09:39:688 b20 eth: job changed
00:09:39:688 b20 new buf size: 0
00:09:39:710 dac Setting DAG epoch #68...
00:09:39:814 b20 got 243 bytes
00:09:39:814 b20 buf: {"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:814 b20 parse packet: 242
00:09:39:814 b20 eth: job is the same
00:09:39:814 b20 new buf size: 0
00:09:41:927 e18 Setting DAG epoch #68 for GPU #1
00:09:41:927 e18 Create GPU buffer for GPU #1
00:09:41:927 e18 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:927 4b0 Setting DAG epoch #68 for GPU #2
00:09:41:928 4b0 Create GPU buffer for GPU #2
00:09:41:928 4b0 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:928 b9c Setting DAG epoch #68 for GPU #3
00:09:41:928 b9c Create GPU buffer for GPU #3
00:09:41:929 b9c OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:929 dac Setting DAG epoch #68 for GPU #0
00:09:41:929 dac Create GPU buffer for GPU #0
00:09:41:929 dac OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:42:494 e44 OC v5, Reset control for GPU 0, close miner right now if you want to use default control from Catalyst
00:09:42:497 e44 OC v5, Reset control for GPU 6, close miner right now if you want to use default control from Catalyst
00:09:42:499 e44 OC v5, Reset control for GPU 12, close miner right now if you want to use default control from Catalyst
00:09:42:502 e44 OC v5, Reset control for GPU 18, close miner right now if you want to use default control from Catalyst
|
|
|
|
|
voidwalker
Newbie
Offline
Activity: 29
Merit: 0
|
|
August 14, 2016, 11:10:12 AM |
|
I use a headless linux rig, well... I try to use lunix in all my PCs  At the end I solved that problem installing X, but only the core. Then add the enviroment variable DISPLAY. [/quote] What do you mean the by core X ? The xorg-server package? So you can run claymore from ssh for example, not inside X, and have ADL working? |
|
|
|
|
vapourminer
Legendary
Offline
Activity: 4326
Merit: 3536
what is this "brake pedal" you speak of?
|
|
August 14, 2016, 12:10:02 PM |
|
hi claymore
[WISHLIST]
[NICE TO HAVE]
can you have the output to the current terminal device list the -cclock value every so often. it would save me checking TRIXX in windows and ssh into ubuntu. i have it set to 1000 mhz in config and it changes every once in a while. i have no idea why.
and i do like doing "localhost:8080" in a browser but it doesnt have the clocks. bonus points if its there too.
also: -cclock value is not in the log file?
|
|
|
|
|
caligvla
Newbie
Offline
Activity: 2
Merit: 0
|
|
August 14, 2016, 12:34:37 PM |
|
Thanks for the help...but still does not work I have no problems using NiceHash's GUI software I usually get 54.7mh/s... wanted to try to use Claymore and focus on Eth for myself. Reconfigured both the Start and config files, already have pagefile more than 16gb. I tried both ways on the esm 0 and 3 still get these errors 00:09:18:804 e44 args: -epool eth-us-east1.nanopool.org:9999 -ewal 0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB -epsw x -esm 0 -estale 0 -dpool http://dcr.maxminers.net:7728 -dwal alexmobile.alexmobile -dpsw 0311 -mode 0 -tt 80
00:09:18:805 e44
00:09:18:806 e44 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
00:09:18:806 e44 º Claymore's Dual ETH + DCR/SC AMD GPU Miner v5.3 Beta º
00:09:18:807 e44 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
00:09:18:807 e44
00:09:19:007 e44 ETH: 1 pool is specified
00:09:19:008 e44 Main Ethereum pool is eth-us-east1.nanopool.org:9999
00:09:19:009 e44 DCR: 1 pool is specified
00:09:19:009 e44 Main Decred pool is dcr.maxminers.net:7728
00:09:20:775 e44 OpenCL platform: AMD Accelerated Parallel Processing
00:09:20:776 e44
Cards available: 4
00:09:20:776 e44 GPU #0: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:776 e44 GPU #1: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #2: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #3: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 Total cards: 4
00:09:20:777 e44 Initializing...
00:09:20:777 e44 GPU #0 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #1 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #2 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #3 recognized as Radeon 270/270X
00:09:20:778 e44 POOL/SOLO version
00:09:20:778 e44 b176
00:09:20:804 e44 start building OpenCL program...
00:09:39:262 e44 done
00:09:39:263 e44 GPU #0: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #1: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #2: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #3: set -etha as 1 (ETH algo for slow cards)
00:09:39:424 b20 ETH: Stratum - connecting to 'eth-us-east1.nanopool.org' <45.55.155.113> port 9999
00:09:39:455 e44 DUAL MINING MODE ENABLED: ETHEREUM+DECRED
00:09:39:455 e44 ETH: eth-proxy stratum mode
00:09:39:455 e44 Watchdog enabled
00:09:39:455 e44 Remote management is enabled on port 3333
00:09:39:456 e44
00:09:39:456 3d0 DCR - connecting to dcr.maxminers.net:7728
00:09:39:456 3d0 http send request: {"method": "getwork", "params": [], "id":0}
00:09:39:466 b20 send: {"worker": "eth1.0", "jsonrpc": "2.0", "params": ["0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB", "x"], "id": 2, "method": "eth_submitLogin"}
00:09:39:466 b20 ETH: Stratum - Connected (eth-us-east1.nanopool.org:9999)
00:09:39:567 3d0 http got answer: {"result":{"data":"01000000f4af4e4667548b12a3c5487c7346b7b92cd1708fcfd7045603130000000000008ff1e94757cd23ff3a88e4f78d0eaad794ae07bfaa7cda0e06f9300d13d920b06fe6b82325e861de5f7f5a7411f42b52145c9d10114f5661ecf1e24b677d239b0100af8114c798db0500000090a300009f62141a8aec30e70000000037d400006e0f000029efaf57000000000000000000000000000000000000000000000000000000000000000000000000000000008000000100000000000005a0","target":"ffffffffffffffffffffffffffffffffffffffffffffffffffffff3f00000000"},"id":0,"error":null}
00:09:39:567 3d0 DCR: Connected (dcr.maxminers.net:7728)
00:09:39:567 3d0 DCR job updated
00:09:39:687 b20 got 282 bytes
00:09:39:687 b20 buf: {"jsonrpc":"2.0","id":2,"result":true}
{"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:687 b20 parse packet: 38
00:09:39:687 b20 ETH: Authorized
00:09:39:688 b20 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}
00:09:39:688 b20 remove first packet 243
00:09:39:688 b20 new buf size: 243
00:09:39:688 b20 parse packet: 242
00:09:39:688 b20 eth: job changed
00:09:39:688 b20 new buf size: 0
00:09:39:710 dac Setting DAG epoch #68...
00:09:39:814 b20 got 243 bytes
00:09:39:814 b20 buf: {"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:814 b20 parse packet: 242
00:09:39:814 b20 eth: job is the same
00:09:39:814 b20 new buf size: 0
00:09:41:927 e18 Setting DAG epoch #68 for GPU #1
00:09:41:927 e18 Create GPU buffer for GPU #1
00:09:41:927 e18 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:927 4b0 Setting DAG epoch #68 for GPU #2
00:09:41:928 4b0 Create GPU buffer for GPU #2
00:09:41:928 4b0 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:928 b9c Setting DAG epoch #68 for GPU #3
00:09:41:928 b9c Create GPU buffer for GPU #3
00:09:41:929 b9c OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:929 dac Setting DAG epoch #68 for GPU #0
00:09:41:929 dac Create GPU buffer for GPU #0
00:09:41:929 dac OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:42:494 e44 OC v5, Reset control for GPU 0, close miner right now if you want to use default control from Catalyst
00:09:42:497 e44 OC v5, Reset control for GPU 6, close miner right now if you want to use default control from Catalyst
00:09:42:499 e44 OC v5, Reset control for GPU 12, close miner right now if you want to use default control from Catalyst
00:09:42:502 e44 OC v5, Reset control for GPU 18, close miner right now if you want to use default control from Catalyst
Hello guys, I have a similar problem. I was mining fine but an hour ago I am now stuck in a Setting DAG Epoch loop between #68 and #69. What is going on? How do I fix this? http://imgur.com/a/H2AkF |
|
|
|
|
alexmobile
Newbie
Offline
Activity: 12
Merit: 0
|
|
August 14, 2016, 12:51:21 PM |
|
I went and searched thru previous posts from users who are getting similar errors.. What I find is consistent is you must have 16mb Pagefile or more and at least 2mb on the video cards (I have this correct) I read several people tried running Catalyst 15.12, 14.9 and newer ver still end up with the same error. But no one has given a straight answer to whats causing it to "not allocate big buffer for DAG" and how to fix. I am sure the community has a solution... Thanks for the help...but still does not work I have no problems using NiceHash's GUI software I usually get 54.7mh/s... wanted to try to use Claymore and focus on Eth for myself. Reconfigured both the Start and config files, already have pagefile more than 16gb. I tried both ways on the esm 0 and 3 still get these errors 00:09:18:804 e44 args: -epool eth-us-east1.nanopool.org:9999 -ewal 0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB -epsw x -esm 0 -estale 0 -dpool http://dcr.maxminers.net:7728 -dwal alexmobile.alexmobile -dpsw 0311 -mode 0 -tt 80
00:09:18:805 e44
00:09:18:806 e44 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
00:09:18:806 e44 º Claymore's Dual ETH + DCR/SC AMD GPU Miner v5.3 Beta º
00:09:18:807 e44 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
00:09:18:807 e44
00:09:19:007 e44 ETH: 1 pool is specified
00:09:19:008 e44 Main Ethereum pool is eth-us-east1.nanopool.org:9999
00:09:19:009 e44 DCR: 1 pool is specified
00:09:19:009 e44 Main Decred pool is dcr.maxminers.net:7728
00:09:20:775 e44 OpenCL platform: AMD Accelerated Parallel Processing
00:09:20:776 e44
Cards available: 4
00:09:20:776 e44 GPU #0: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:776 e44 GPU #1: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #2: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #3: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 Total cards: 4
00:09:20:777 e44 Initializing...
00:09:20:777 e44 GPU #0 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #1 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #2 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #3 recognized as Radeon 270/270X
00:09:20:778 e44 POOL/SOLO version
00:09:20:778 e44 b176
00:09:20:804 e44 start building OpenCL program...
00:09:39:262 e44 done
00:09:39:263 e44 GPU #0: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #1: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #2: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #3: set -etha as 1 (ETH algo for slow cards)
00:09:39:424 b20 ETH: Stratum - connecting to 'eth-us-east1.nanopool.org' <45.55.155.113> port 9999
00:09:39:455 e44 DUAL MINING MODE ENABLED: ETHEREUM+DECRED
00:09:39:455 e44 ETH: eth-proxy stratum mode
00:09:39:455 e44 Watchdog enabled
00:09:39:455 e44 Remote management is enabled on port 3333
00:09:39:456 e44
00:09:39:456 3d0 DCR - connecting to dcr.maxminers.net:7728
00:09:39:456 3d0 http send request: {"method": "getwork", "params": [], "id":0}
00:09:39:466 b20 send: {"worker": "eth1.0", "jsonrpc": "2.0", "params": ["0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB", "x"], "id": 2, "method": "eth_submitLogin"}
00:09:39:466 b20 ETH: Stratum - Connected (eth-us-east1.nanopool.org:9999)
00:09:39:567 3d0 http got answer: {"result":{"data":"01000000f4af4e4667548b12a3c5487c7346b7b92cd1708fcfd7045603130000000000008ff1e94757cd23ff3a88e4f78d0eaad794ae07bfaa7cda0e06f9300d13d920b06fe6b82325e861de5f7f5a7411f42b52145c9d10114f5661ecf1e24b677d239b0100af8114c798db0500000090a300009f62141a8aec30e70000000037d400006e0f000029efaf57000000000000000000000000000000000000000000000000000000000000000000000000000000008000000100000000000005a0","target":"ffffffffffffffffffffffffffffffffffffffffffffffffffffff3f00000000"},"id":0,"error":null}
00:09:39:567 3d0 DCR: Connected (dcr.maxminers.net:7728)
00:09:39:567 3d0 DCR job updated
00:09:39:687 b20 got 282 bytes
00:09:39:687 b20 buf: {"jsonrpc":"2.0","id":2,"result":true}
{"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:687 b20 parse packet: 38
00:09:39:687 b20 ETH: Authorized
00:09:39:688 b20 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}
00:09:39:688 b20 remove first packet 243
00:09:39:688 b20 new buf size: 243
00:09:39:688 b20 parse packet: 242
00:09:39:688 b20 eth: job changed
00:09:39:688 b20 new buf size: 0
00:09:39:710 dac Setting DAG epoch #68...
00:09:39:814 b20 got 243 bytes
00:09:39:814 b20 buf: {"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:814 b20 parse packet: 242
00:09:39:814 b20 eth: job is the same
00:09:39:814 b20 new buf size: 0
00:09:41:927 e18 Setting DAG epoch #68 for GPU #1
00:09:41:927 e18 Create GPU buffer for GPU #1
00:09:41:927 e18 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:927 4b0 Setting DAG epoch #68 for GPU #2
00:09:41:928 4b0 Create GPU buffer for GPU #2
00:09:41:928 4b0 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:928 b9c Setting DAG epoch #68 for GPU #3
00:09:41:928 b9c Create GPU buffer for GPU #3
00:09:41:929 b9c OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:929 dac Setting DAG epoch #68 for GPU #0
00:09:41:929 dac Create GPU buffer for GPU #0
00:09:41:929 dac OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:42:494 e44 OC v5, Reset control for GPU 0, close miner right now if you want to use default control from Catalyst
00:09:42:497 e44 OC v5, Reset control for GPU 6, close miner right now if you want to use default control from Catalyst
00:09:42:499 e44 OC v5, Reset control for GPU 12, close miner right now if you want to use default control from Catalyst
00:09:42:502 e44 OC v5, Reset control for GPU 18, close miner right now if you want to use default control from Catalyst
Hello guys, I have a similar problem. I was mining fine but an hour ago I am now stuck in a Setting DAG Epoch loop between #68 and #69. What is going on? How do I fix this? http://imgur.com/a/H2AkF |
|
|
|
|
caligvla
Newbie
Offline
Activity: 2
Merit: 0
|
|
August 14, 2016, 12:55:03 PM |
|
I've been mining a month and never had this issue before... Im running Win 10, 16 GB virtual memory, 4gb ram, claymore 5.2, 6x RX 480 8 GB, Drivers 16.7.2. It's really bizarre! I think this has impacted a lot of people. I'm using Alpereum for mining and I can see that about two hour sago the hashrate halved, same time when my issues began (12:57 CET) I went and searched thru previous posts from users who are getting similar errors.. What I find is consistent is you must have 16mb Pagefile or more and at least 2mb on the video cards (I have this correct) I read several people tried running Catalyst 15.12, 14.9 and newer ver still end up with the same error. But no one has given a straight answer to whats causing it to "not allocate big buffer for DAG" and how to fix. I am sure the community has a solution... Thanks for the help...but still does not work I have no problems using NiceHash's GUI software I usually get 54.7mh/s... wanted to try to use Claymore and focus on Eth for myself. Reconfigured both the Start and config files, already have pagefile more than 16gb. I tried both ways on the esm 0 and 3 still get these errors 00:09:18:804 e44 args: -epool eth-us-east1.nanopool.org:9999 -ewal 0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB -epsw x -esm 0 -estale 0 -dpool http://dcr.maxminers.net:7728 -dwal alexmobile.alexmobile -dpsw 0311 -mode 0 -tt 80
00:09:18:805 e44
00:09:18:806 e44 ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
00:09:18:806 e44 º Claymore's Dual ETH + DCR/SC AMD GPU Miner v5.3 Beta º
00:09:18:807 e44 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
00:09:18:807 e44
00:09:19:007 e44 ETH: 1 pool is specified
00:09:19:008 e44 Main Ethereum pool is eth-us-east1.nanopool.org:9999
00:09:19:009 e44 DCR: 1 pool is specified
00:09:19:009 e44 Main Decred pool is dcr.maxminers.net:7728
00:09:20:775 e44 OpenCL platform: AMD Accelerated Parallel Processing
00:09:20:776 e44
Cards available: 4
00:09:20:776 e44 GPU #0: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:776 e44 GPU #1: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #2: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 GPU #3: name: Pitcairn, 2048 MB available, 20 compute units
00:09:20:777 e44 Total cards: 4
00:09:20:777 e44 Initializing...
00:09:20:777 e44 GPU #0 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #1 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #2 recognized as Radeon 270/270X
00:09:20:778 e44 GPU #3 recognized as Radeon 270/270X
00:09:20:778 e44 POOL/SOLO version
00:09:20:778 e44 b176
00:09:20:804 e44 start building OpenCL program...
00:09:39:262 e44 done
00:09:39:263 e44 GPU #0: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #1: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #2: set -etha as 1 (ETH algo for slow cards)
00:09:39:263 e44 GPU #3: set -etha as 1 (ETH algo for slow cards)
00:09:39:424 b20 ETH: Stratum - connecting to 'eth-us-east1.nanopool.org' <45.55.155.113> port 9999
00:09:39:455 e44 DUAL MINING MODE ENABLED: ETHEREUM+DECRED
00:09:39:455 e44 ETH: eth-proxy stratum mode
00:09:39:455 e44 Watchdog enabled
00:09:39:455 e44 Remote management is enabled on port 3333
00:09:39:456 e44
00:09:39:456 3d0 DCR - connecting to dcr.maxminers.net:7728
00:09:39:456 3d0 http send request: {"method": "getwork", "params": [], "id":0}
00:09:39:466 b20 send: {"worker": "eth1.0", "jsonrpc": "2.0", "params": ["0xEDa996a87AAaF6fa15580ADa4da6Da235bea21eB", "x"], "id": 2, "method": "eth_submitLogin"}
00:09:39:466 b20 ETH: Stratum - Connected (eth-us-east1.nanopool.org:9999)
00:09:39:567 3d0 http got answer: {"result":{"data":"01000000f4af4e4667548b12a3c5487c7346b7b92cd1708fcfd7045603130000000000008ff1e94757cd23ff3a88e4f78d0eaad794ae07bfaa7cda0e06f9300d13d920b06fe6b82325e861de5f7f5a7411f42b52145c9d10114f5661ecf1e24b677d239b0100af8114c798db0500000090a300009f62141a8aec30e70000000037d400006e0f000029efaf57000000000000000000000000000000000000000000000000000000000000000000000000000000008000000100000000000005a0","target":"ffffffffffffffffffffffffffffffffffffffffffffffffffffff3f00000000"},"id":0,"error":null}
00:09:39:567 3d0 DCR: Connected (dcr.maxminers.net:7728)
00:09:39:567 3d0 DCR job updated
00:09:39:687 b20 got 282 bytes
00:09:39:687 b20 buf: {"jsonrpc":"2.0","id":2,"result":true}
{"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:687 b20 parse packet: 38
00:09:39:687 b20 ETH: Authorized
00:09:39:688 b20 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}
00:09:39:688 b20 remove first packet 243
00:09:39:688 b20 new buf size: 243
00:09:39:688 b20 parse packet: 242
00:09:39:688 b20 eth: job changed
00:09:39:688 b20 new buf size: 0
00:09:39:710 dac Setting DAG epoch #68...
00:09:39:814 b20 got 243 bytes
00:09:39:814 b20 buf: {"jsonrpc":"2.0","id":0,"result":["0x418107c5c15fb00abb0eca602a23123a6e0c1cae3b63e6498956820d157d2122","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
00:09:39:814 b20 parse packet: 242
00:09:39:814 b20 eth: job is the same
00:09:39:814 b20 new buf size: 0
00:09:41:927 e18 Setting DAG epoch #68 for GPU #1
00:09:41:927 e18 Create GPU buffer for GPU #1
00:09:41:927 e18 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:927 4b0 Setting DAG epoch #68 for GPU #2
00:09:41:928 4b0 Create GPU buffer for GPU #2
00:09:41:928 4b0 OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:928 b9c Setting DAG epoch #68 for GPU #3
00:09:41:928 b9c Create GPU buffer for GPU #3
00:09:41:929 b9c OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:41:929 dac Setting DAG epoch #68 for GPU #0
00:09:41:929 dac Create GPU buffer for GPU #0
00:09:41:929 dac OpenCL error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
00:09:42:494 e44 OC v5, Reset control for GPU 0, close miner right now if you want to use default control from Catalyst
00:09:42:497 e44 OC v5, Reset control for GPU 6, close miner right now if you want to use default control from Catalyst
00:09:42:499 e44 OC v5, Reset control for GPU 12, close miner right now if you want to use default control from Catalyst
00:09:42:502 e44 OC v5, Reset control for GPU 18, close miner right now if you want to use default control from Catalyst
Hello guys, I have a similar problem. I was mining fine but an hour ago I am now stuck in a Setting DAG Epoch loop between #68 and #69. What is going on? How do I fix this? http://imgur.com/a/H2AkF |
|
|
|
|
vapourminer
Legendary
Offline
Activity: 4326
Merit: 3536
what is this "brake pedal" you speak of?
|
|
August 14, 2016, 01:21:55 PM |
|
win 7 pro x64 16 gigs ram here. windows sets whatever page file it wants. plus ubuntu 15.10 desktop, x64 4 gigs ram, and it does whatever it wants too. i have no idea what its swap is set at. and it does work absolutely no problems here on both systems. just figured id toss that out here. I've been mining a month and never had this issue before... Im running Win 10, 16 GB virtual memory, 4gb ram, claymore 5.2, 6x RX 480 8 GB, Drivers 16.7.2. It's really bizarre! I think this has impacted a lot of people. I'm using Alpereum for mining and I can see that about two hour sago the hashrate halved, same time when my issues began (12:57 CET) I went and searched thru previous posts from users who are getting similar errors..
What I find is consistent is you must have 16mb Pagefile or more and at least 2mb on the video cards (I have this correct)
I read several people tried running Catalyst 15.12, 14.9 and newer ver still end up with the same
Hello guys, I have a similar problem. I was mining fine but an hour ago I am now stuck in a Setting DAG Epoch loop between #68 and #69. What is going on? How do I fix this?  [/quote] [/quote] |
|
|
|
|
alexmobile
Newbie
Offline
Activity: 12
Merit: 0
|
|
August 14, 2016, 01:37:28 PM |
|
Ok so I did just that allowed windows to set what it wants as a pagefile and still have the same issues I also have win 7 64 with 4x Windforce Radeon R9 270X 2GB Drivers 16.7.3. AAARGGHH! win 7 pro x64 16 gigs ram here. windows sets whatever page file it wants. plus ubuntu 15.10 desktop, x64 4 gigs ram, and it does whatever it wants too. i have no idea what its swap is set at. and it does work absolutely no problems here on both systems. just figured id toss that out here. I've been mining a month and never had this issue before... Im running Win 10, 16 GB virtual memory, 4gb ram, claymore 5.2, 6x RX 480 8 GB, Drivers 16.7.2. It's really bizarre! I think this has impacted a lot of people. I'm using Alpereum for mining and I can see that about two hour sago the hashrate halved, same time when my issues began (12:57 CET) I went and searched thru previous posts from users who are getting similar errors..
What I find is consistent is you must have 16mb Pagefile or more and at least 2mb on the video cards (I have this correct)
I read several people tried running Catalyst 15.12, 14.9 and newer ver still end up with the same
Hello guys, I have a similar problem. I was mining fine but an hour ago I am now stuck in a Setting DAG Epoch loop between #68 and #69. What is going on? How do I fix this? http://imgur.com/a/H2AkF[/quote] [/quote] |
|
|
|
|
TimLev
Newbie
Offline
Activity: 13
Merit: 0
|
|
August 14, 2016, 01:59:01 PM |
|
Hello, Claymore!
I am not an Englishman, so I apologize for the language in advance.
Regularly one card in rig starts to continuously get incorrect shares. It can work 3-5-10 days 24/7 with no problem, and suddenly all the shares are incorrect: "GPU #2 got incorrect share. If you see this warning often, make sure you did not overclock it too much!"
Overclocked or not does not matter, the same result. After rebooting begins to work well next period.
Would be very good if the miner will be have watchdog option: if 9 of 10 last shares from one card are incorrect, then execute reboot.bat.
(Rig configuration: 2x Sapphire Nitro R9 390, 2x Gigabyte R9 290 3X, 1x Sapphire R9 290 3X, MB GIGABYTE GA-X38-DS4, Win 10, Crimson 15.12, Claymore's miner 5.1 beta, Eth only) (GPU #2 - Gigabyte R9 290 3X 1040/1250)
|
|
|
|
|
|
pwpwpw
|
|
August 14, 2016, 02:46:59 PM |
|
Ok so I did just that allowed windows to set what it wants as a pagefile and still have the same issues
I also have win 7 64
with 4x Windforce Radeon R9 270X 2GB
Drivers 16.7.3.
AAARGGHH!
set fixed pagefile, I have minimum 18GB, maximum 36GB. |
|
|
|
|
pwpwpw
|
|
August 14, 2016, 02:49:41 PM |
|
I had a weird bug where a 80C card was read as 135C and I have -tstop 95, my question is, if any card reach tstop, they will never start again ? Is there a way to start them after a fixed time, or temp? I had it running for a few minutes, went down to 40C but didn't start again. 17:35:26:901 15f8 parse packet: 242
17:35:26:901 15f8 eth: job changed
17:35:26:901 15f8 new buf size: 0
17:35:26:901 15f8 ETH: 08/14/16-17:35:26 - New job from etc-eu1.nanopool.org:19999
17:35:26:901 15f8 target: 0x00000000dbe6fece (diff: 5000MH), epoch #68
17:35:26:901 15f8 ETH - Total Speed: 27.476 Mh/s, Total Shares: 1163, Rejected: 1, Time: 60:51
17:35:26:902 15f8 ETH: GPU0 27.476 Mh/s
17:35:26:902 15f8 SC - Total Speed: 480.836 Mh/s, Total Shares: 2123, Rejected: 0
17:35:26:902 15f8 SC: GPU0 480.836 Mh/s
17:35:29:609 bb8 GPU 0 temp = 80, old fan speed = 100, new fan speed = 100
17:35:29:979 15f8 ETH: checking pool connection...
17:35:29:979 15f8 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}
17:35:30:035 15f8 got 243 bytes
17:35:30:035 15f8 buf: {"jsonrpc":"2.0","id":0,"result":["0xbba0011a7a3bac48f18ef8a0441566fedb92fe630298ad10f097fa932983fe1b","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
17:35:30:035 15f8 parse packet: 242
17:35:30:035 15f8 eth: job is the same
17:35:30:035 15f8 new buf size: 0
17:35:32:717 bb8 GPU #0 reached STOP temperature (135 >= 95), stop mining on this GPU.
17:35:32:718 bb8 GPU 0 temp = 135, old fan speed = 100, new fan speed = 100
17:35:35:724 bb8 GPU 0 temp = 73, old fan speed = 100, new fan speed = 100
17:35:37:808 15f8 send: {"id":6,"jsonrpc":"2.0","method":"eth_submitHashrate","params":["0x1a1b185", "0x00000000000000000000000000000000000000000000000000000000b5648154"]}
17:35:38:728 bb8 GPU 0 temp = 68, old fan speed = 100, new fan speed = 100
17:35:39:993 15f8 ETH: checking pool connection...
17:35:39:993 15f8 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}
17:35:40:052 15f8 got 243 bytes
17:35:40:052 15f8 buf: {"jsonrpc":"2.0","id":0,"result":["0xbba0011a7a3bac48f18ef8a0441566fedb92fe630298ad10f097fa932983fe1b","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
17:35:40:052 15f8 parse packet: 242
17:35:40:052 15f8 eth: job is the same
17:35:40:052 15f8 new buf size: 0
17:35:41:731 bb8 GPU 0 temp = 66, old fan speed = 100, new fan speed = 100
17:35:41:734 bb8 GPU0 t=66C fan=100%
17:35:41:735 bb8 em hbt: 0, dm hbt: 0, fm hbt: 47,
17:35:41:735 bb8 watchdog - thread 0, hb time 94
17:35:41:735 bb8 watchdog - thread 1, hb time 63
17:35:44:261 15f8 got 243 bytes
17:35:44:261 15f8 buf: {"jsonrpc":"2.0","id":0,"result":["0x8939de0b3d3b7262ebca2980616e96f20a78ad2deba7dff212671b6fe44cbf4b","0xdeb13fd7c8eb5b6e43fe49e77f32c5e38fd7679be198414e839c7e1b83f17dc5","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}
17:35:44:261 15f8 parse packet: 242
17:35:44:262 15f8 eth: job changed
17:35:44:262 15f8 new buf size: 0
17:35:44:262 15f8 ETH: 08/14/16-17:35:44 - New job from etc-eu1.nanopool.org:19999
17:35:44:262 15f8 target: 0x00000000dbe6fece (diff: 5000MH), epoch #68
17:35:44:262 15f8 ETH - Total Speed: 0.000 Mh/s, Total Shares: 1163, Rejected: 1,
|
|
|
|
mkimid
Sr. Member
Offline
Activity: 336
Merit: 250
Have A Nice Day
|
|
August 14, 2016, 03:16:09 PM |
|
I feel as v5.3 version is not compatible with Parity v1.3.0 solo mining ?
It just return an error -32600 :
I have tested with ethminer (cpp version and genoil version), all working well.
I think, it is a problem with this miner
-or- maybe some kind of special option
|
Have a nice day
|
|
|
alexmobile
Newbie
Offline
Activity: 12
Merit: 0
|
|
August 14, 2016, 03:40:27 PM |
|
Question is one miner better than another when it comes to HAsh Rates? I am trying to set this Claymore up but cant seem to get it squared (yes I have pagefile set to 25Gb min and 5Gb max) Have used SGminer for X11 coins worked Fine Cpu miner for X11 coins worked fine Nicehash uses Genoil and it works fine but I want to keep my mined ETH not give away my power. Any suggestions for ETH solo/pool mining or dual ETH mining with additional coin?? Thanks  I feel as v5.3 version is not compatible with Parity v1.3.0 solo mining ?
It just return an error -32600 :
I have tested with ethminer (cpp version and genoil version), all working well.
I think, it is a problem with this miner
-or- maybe some kind of special option
|
|
|
|
|
mkimid
Sr. Member
Offline
Activity: 336
Merit: 250
Have A Nice Day
|
|
August 14, 2016, 04:07:59 PM |
|
i want to recommend the dual mining ETH or ETC with SIA This miner is best for the dual mining If it can support Solo Mining with Parity 1.3.0 Maybe ETC (solo) + SIA (pool) It will maximize the profit Question is one miner better than another when it comes to HAsh Rates? I am trying to set this Claymore up but cant seem to get it squared (yes I have pagefile set to 25Gb min and 5Gb max) Have used SGminer for X11 coins worked Fine Cpu miner for X11 coins worked fine Nicehash uses Genoil and it works fine but I want to keep my mined ETH not give away my power. Any suggestions for ETH solo/pool mining or dual ETH mining with additional coin?? Thanks I feel as v5.3 version is not compatible with Parity v1.3.0 solo mining ?
It just return an error -32600 :
I have tested with ethminer (cpp version and genoil version), all working well.
I think, it is a problem with this miner
-or- maybe some kind of special option
|
Have a nice day
|
|
|
alexmobile
Newbie
Offline
Activity: 12
Merit: 0
|
|
August 14, 2016, 04:08:22 PM |
|
I have tried 16, 25, 50gb Pagefiles also let windows set pagefile, nothing works may need to look for alternative Miner when I get some time to research which would give the best HashRate if any over another. any suggestions??? Ok so I did just that allowed windows to set what it wants as a pagefile and still have the same issues
I also have win 7 64
with 4x Windforce Radeon R9 270X 2GB
Drivers 16.7.3.
AAARGGHH!
set fixed pagefile, I have minimum 18GB, maximum 36GB. |
|
|
|
|
alexmobile
Newbie
Offline
Activity: 12
Merit: 0
|
|
August 14, 2016, 04:30:24 PM |
|
What the name of this dual miner? i want to recommend the dual mining ETH or ETC with SIA This miner is best for the dual mining If it can support Solo Mining with Parity 1.3.0 Maybe ETC (solo) + SIA (pool) It will maximize the profit Question is one miner better than another when it comes to HAsh Rates? I am trying to set this Claymore up but cant seem to get it squared (yes I have pagefile set to 25Gb min and 5Gb max) Have used SGminer for X11 coins worked Fine Cpu miner for X11 coins worked fine Nicehash uses Genoil and it works fine but I want to keep my mined ETH not give away my power. Any suggestions for ETH solo/pool mining or dual ETH mining with additional coin?? Thanks I feel as v5.3 version is not compatible with Parity v1.3.0 solo mining ?
It just return an error -32600 :
I have tested with ethminer (cpp version and genoil version), all working well.
I think, it is a problem with this miner
-or- maybe some kind of special option
|
|
|
|
|
z0n0
Legendary
Offline
Activity: 1274
Merit: 1006
|
|
August 14, 2016, 04:33:28 PM |
|
If a guy wants to jump in mining and has free electricity, what do you guys recommend to strat with?
For start just 2 or 3 GPU.
Is it better to pay more and buy new RX 470/480 or used maybe 290 or 280x?
Here in my country used 290 can be found at 190EUR, used 280x at 140EUR, while new RX or even 390 is about 290EUR.
Looking forward hearing from you guys, cheers!
|
|
|
|
|
RobertD
Newbie
Offline
Activity: 42
Merit: 0
|
|
August 14, 2016, 04:44:43 PM |
|
290/290x if you have free electricity ( expect 250w-350w at the wall while dual mining )
rx480 if you can get them cheap
------------------------------------------------------------------------------------------------
280x ( 1175mhz core / 1700mhz mem ) hashes around 17mhs ETH + 500mhs SIA
290x ( 1125MHZ core / 1500MHz mem ) hashes around 31mhs ETH + 620mhs SIA
390 are similar to 290x, not worth the extra price
|
|
|
|
|
|
