Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[elgi76]

@claymore
GTX 1060 3GB

how much Mh/s you have with this gpu ?

[wll1rah]

@claymore
GTX 1060 3GB

how much Mh/s you have with this gpu ?

ETH 23MHs + 217MHs SC cdri 35 turning off sia doesn't increase speed of ETH with power limit at 103%
ETH 22.4MHs + 260 MHs SC dcri 35 powerlimit set to 88

[djraven911]

hi, i have 2 rigs same cloned config with 6 cards, using win 7 x64 and catalyst 15.2 and 16gb virtual ram.

I noticed today that both rigs see my 4gb r9 380 cards as 3gb ram. In catalyst driver and windows it shows 4gb. I have no ideea why. I am sure 6 months ago with an older version of claymores miner it showed 4gb ram. However i updated the miner many times since then, but i guess i didnt notice when the change happened.

Does this mean the miner sees only 3gb ram? Anyone knows how can i fix this?
everything else works fine even like this but im worried when the dag will be over 3gb...
thanks my fella miners and good luck in all!

[Claymore]

@claymore

I have a rig with 4 GPU's
Intel HD4400
HD 7870 XT
(2)GTX 1060 3GB

Claymore's dual miner ... 7.0

Issues is that only the temps are displayed for the Nvidia cards and not the AMD card?  Is this an issue with the video being plugged into the Intel igpu and not the AMD card or something else?

Log file contains info about the reason.

[armyman]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

[citronick]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

Did you power the molex connector on the ASrock mobo?

For multi GPU setup, you need this for extra power going to the GPUs in addition to powered USB risers.

Plus... you also need to set minimum 16GB virtual windows memory.

[armyman]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

Did you power the molex connector on the ASrock mobo?

For multi GPU setup, you need this for extra power going to the GPUs in addition to powered USB risers.

Plus... you also need to set minimum 16GB virtual windows memory.

Thank you, I will try it now and see how it goes!

[xeridea]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

Did you power the molex connector on the ASrock mobo?

For multi GPU setup, you need this for extra power going to the GPUs in addition to powered USB risers.

Plus... you also need to set minimum 16GB virtual windows memory.

I don't know why lots of people think you need to power the molex on mobo.  If using the 1x-16x powered USB risers, they are completely unnecessary.  The risers are all powered, there is 0.00000w going through the slots on the motherboard.  The molex on mobo are for if you are using non powered risers.  I have that board, and it will run fine with 6 cards, nothing plugged into mobo.

[Alehandros]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

I have a few of these boards setup and they can be quite fussy, try adding the 4th GPU into each spare slot in turn.

For example, 1 of the H81s will not work at all, if the x16 slot is used so that rig only gets 5 cards :/

[armyman]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

I have a few of these boards setup and they can be quite fussy, try adding the 4th GPU into each spare slot in turn.

For example, 1 of the H81s will not work at all, if the x16 slot is used so that rig only gets 5 cards :/

You mean to try the slots one by one? So it could be a mobo problem?

[GH]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

Quite some people are talking about lowering pci-e gen in BIOS from 3 to 2 or even 1 in order to get more than 3/4 GPUs running. Maybe that's the issue? (Note: I don't use the BTC Pro boards and I don't have that kind of issue with any of my (countless) rigs, so it could be something completely different...)

Good luck!

Edit: ...and 8/4/4 for the x16 slot if this is possible in this board's BIOS...

[tutorialevideo]

Hi there claymore suports getwork?

[willi9974]

Plug your Display into a other GPU
If i start my Miner i had a black screen on the last GPU, so i move my Display to a other Card an tut works

Best Regards
Willi

[armyman]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

Quite some people are talking about lowering pci-e gen in BIOS from 3 to 2 or even 1 in order to get more than 3/4 GPUs running. Maybe that's the issue? (Note: I don't use the BTC Pro boards and I don't have that kind of issue with any of my (countless) rigs, so it could be something completely different...)

Good luck!

Edit: ...and 8/4/4 for the x16 slot if this is possible in this board's BIOS...

What I have tried so far is:

- lowering pci to GEN1 in BIOS
- remove any possible interfering software
- visrtual mem. to 16 gb

So far we have been able to make 5 GPUs run at the same time, now we are trying to understand if the last one has a riser problem, or something else.

Which mobo do you suggest for an eventual next rig?

Also which field of the BIOS should I edit with "8/4/4 for the x16 slot"?

Thanks

[Meech]

Guys I am trying to set up the following rig:

Asrock H81 pro btc
16 gb ram DDR3
6 x XFX RX480 8gb
6 x PCI 1x 16
SSD external memory
Intel Pentium G3260
1200 w PSU
WIN 10 64 bit

I would like to install the latest version of Claymore's dual miner on it, the problem is that the PC can not even run the 6 GPU's all the same time apparently, without anything installed on it yet, but Windows (I am helping which is setting it up and we are about 2000 miles far from each other, so this doesn't help).

Windows starts normally if only 3 GPUs are connected, but a black screen will come off if we try to connect all the 6 GPU's.

Any idea?

Also which drivers would you recommend for the XFX RX480 8gb? Is the latest crimson driver ok?

Any help would be deeply appreciated, thank you!

I have a few of these boards setup and they can be quite fussy, try adding the 4th GPU into each spare slot in turn.

For example, 1 of the H81s will not work at all, if the x16 slot is used so that rig only gets 5 cards :/

You mean to try the slots one by one? So it could be a mobo problem?

Powered risers would help but definately connect mobo molex connector to the psu to give juice to the pcie slots.  If using windows all should be good.  I had problems with Linux on that mobo.

[tutorialevideo]

on ubuntu i get this syslog 50GB

-rw-r-----  1 syslog adm    51086061568 sep 21 20:17 kern.log
drwx--x--x  2 root   root          4096 sep 21 14:27 lightdm
-rw-r-----  1 syslog adm    51086168064 sep 21 20:17 syslog
-rw-rw-r--  1 root   utmp          2304 sep 21 14:43 wtmp
-rw-r--r--  1 root   root        369812 sep 21 14:45 Xorg.0.log
user@user-To-be-filled-by-O-E-M:/var/log$ tail -f kern.log
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730901] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E044001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730902] VM fault (0x01, vmid 7) at page 135284862, read from 'TC5' (0x54433500) (68)
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730915] amdgpu 0000:04:00.0: GPU fault detected: 147 0x03d0c401
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730916] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_ADDR   0x0810487A
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730916] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C4001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730917] VM fault (0x01, vmid 7) at page 135284858, read from 'TC3' (0x54433300) (196)
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730926] amdgpu 0000:05:00.0: GPU fault detected: 147 0x03e8c801
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730927] amdgpu 0000:05:00.0:   VM_CONTEXT1_PROTECTION_FAULT_ADDR   0x0810487D
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730928] amdgpu 0000:05:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C8001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730929] VM f^C

[Claymore]

on ubuntu i get this syslog 50GB

-rw-r-----  1 syslog adm    51086061568 sep 21 20:17 kern.log
drwx--x--x  2 root   root          4096 sep 21 14:27 lightdm
-rw-r-----  1 syslog adm    51086168064 sep 21 20:17 syslog
-rw-rw-r--  1 root   utmp          2304 sep 21 14:43 wtmp
-rw-r--r--  1 root   root        369812 sep 21 14:45 Xorg.0.log
user@user-To-be-filled-by-O-E-M:/var/log$ tail -f kern.log
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730901] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E044001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730902] VM fault (0x01, vmid 7) at page 135284862, read from 'TC5' (0x54433500) (68)
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730915] amdgpu 0000:04:00.0: GPU fault detected: 147 0x03d0c401
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730916] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_ADDR   0x0810487A
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730916] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C4001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730917] VM fault (0x01, vmid 7) at page 135284858, read from 'TC3' (0x54433300) (196)
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730926] amdgpu 0000:05:00.0: GPU fault detected: 147 0x03e8c801
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730927] amdgpu 0000:05:00.0:   VM_CONTEXT1_PROTECTION_FAULT_ADDR   0x0810487D
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730928] amdgpu 0000:05:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C8001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730929] VM f^C

"-etha 2" will help you. Within 24 hours I will release an update, this option will be set automatically on Linux+gpupro.

[tutorialevideo]

on ubuntu i get this syslog 50GB

-rw-r-----  1 syslog adm    51086061568 sep 21 20:17 kern.log
drwx--x--x  2 root   root          4096 sep 21 14:27 lightdm
-rw-r-----  1 syslog adm    51086168064 sep 21 20:17 syslog
-rw-rw-r--  1 root   utmp          2304 sep 21 14:43 wtmp
-rw-r--r--  1 root   root        369812 sep 21 14:45 Xorg.0.log
user@user-To-be-filled-by-O-E-M:/var/log$ tail -f kern.log
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730901] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E044001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730902] VM fault (0x01, vmid 7) at page 135284862, read from 'TC5' (0x54433500) (68)
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730915] amdgpu 0000:04:00.0: GPU fault detected: 147 0x03d0c401
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730916] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_ADDR   0x0810487A
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730916] amdgpu 0000:04:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C4001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730917] VM fault (0x01, vmid 7) at page 135284858, read from 'TC3' (0x54433300) (196)
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730926] amdgpu 0000:05:00.0: GPU fault detected: 147 0x03e8c801
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730927] amdgpu 0000:05:00.0:   VM_CONTEXT1_PROTECTION_FAULT_ADDR   0x0810487D
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730928] amdgpu 0000:05:00.0:   VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C8001
Sep 21 15:35:12 user-To-be-filled-by-O-E-M kernel: [ 4060.730929] VM f^C

"-etha 2" will help you. Within 24 hours I will release an update, this option will be set automatically on Linux+gpupro.

Thank you, i build my own getwork pool but.. i am trying to mine with claymore on it is posible?

[Claymore]

Thank you, i build my own getwork pool but.. i am trying to mine with claymore on it is posible?

Solo mode is supported. Read OP or Readme for sample command line.

[hcarpach]

Hey Claymore, will you support Zcash mining with your software? lots of miners are expecting that coin release.