trbittr
Member
Offline
Activity: 89
Merit: 13
|
|
May 10, 2017, 10:24:01 AM |
|
@searing
what power suply do you have for the L3+ or do you have the recommended APW3+ PSU from btmain?
|
|
|
|
wck
Member
Offline
Activity: 70
Merit: 10
|
|
May 10, 2017, 10:58:11 AM |
|
How do the pools setup work? why are there 3? does it switch?
Bitmain has traditionally used a "rollover" setup on pools, so that if pool 0 is down the miner will use pool 1 and if pools 0 and 1 are both down it will use pool 2. They normally autoswitch back to a lower pool number when it comes up, IME with the S5, but it might take several seconds to a minute to do so when it does so. IMO those folks asking $3500 are way high on their price - I could see charging $2000 as a "available now" surcharge but IMO $3500 is a blatant eBay-level ripoff. I just sold my L3 hash on hashnest for over 0.29 LTC / MH ... that works out to over the $3500 L3 miner at LTC prices this morning. If the market is there it isn't ripping people off. People don't have to buy and people don't have to sell for low prices. I agree i think $3500 are justified... to be honest I also sold half my hash for 0.2949999 Mhs/LTC recuperated my intital $1900 investment left with 268Mh/s i think i will just let it run to mine some LTC as LTC just broke through $34 on Gdax and it looks like $50 is possible. me I just mine at 25% off the expected taxes I would have to pay on income I get off 100% off gross income ..again 25% off equipment in real $$$ saved I would have had to pay the IRS...I just run them down to doorstops....it works quite well actually (2015 not so much) but still so a 1370 may 15th order of 4 is (not including shipping I forget what that was) so say 1370 x 4 = $5580.00 usd at 25% off is = $ 1370 savings x 75% ...so...in my case that is buy 4 get one FREE vs what I can mine out of them...I'm good and again legal miner USA paying income tax to IRS...but hell this works dandy whatever...cost of doing business...if you can get the equipment at the right time and coin pumps that is IT is not very complicated (ducks...hey don't throw stuff at me in the thread!) Dumb and lucky..sometimes it is just dumb and lucky wins the race Yup Dumb and Lucky in my case. I am so glad I did sell it at 0.29499 LTC per Mh its back down to 0.25 LTC per Mh I can buy it all back cheaper almost 80% of the value I paid. Naah going to stick with my initial assesment hedge your bets diversify and de-risk. To make my decision on whether to sell the Hash Rate I created a Model on Excel here I will share it. https://docs.google.com/spreadsheets/d/10zdrYw3G1iworRHH25ncmLFOs6u6jSjfnrN9Dvr_ZYI/edit#gid=0photos uploadThe biggest change now on future equipment is on how I do the calculations. Before if I though LTC say was gonna double, I'd buy a bitmain unit or so the logic goes....go with the gut but trust the math. Now however, say that LTC went up to $50 per LTC ..... with bitmain pulling a 'firmware problem' the last time the coin went up 4x and/or with seg witness..what is to stop them from saying the same thing and have a 'firmware error' if my 1 left coming July batch L3+ arriving 6 weeks late while they mine with it!!!! I had 8 L3's on April 1st or so...thru eastshore...eastshore said they 'literally' we're pulling them out of the trucks in bitmain's lot...I got 4 and they took 4 back...and of course BTC limbo to get the coin back....firmware problem my ass......(also told by april 15th users that got L3+'s after the firmware error was fixed the firmware was still dated Jan 2017) So ...not sure...the frigging math has changed...large gains in coin price now means bitmain can just frigging do as they wish it seems...I'll have to take that into consideration.I wonder if LTC hits $50-$75 bucks if I will even see my last L3+ on a July purchase....this could be rinse/wash/repeat AS for my evil wish If they would just stop selling miners..mine themselves and just offer hashnet..I could live with that I mean really ..if you are gonna do evil do it correctly....no pride in their work...wizzing in their own pool driving difficulty up....look at knc they took pre-orders on Neptune btc miners in 2015 with customers money..filled up their data halls and mined them 5-6 months..then shipped the Neptune's late..and the owners got maybe 1/4 of the price back before they were door stops....completely screwed..and knc WON the court case against them too boot! Bitmain has ...no pride in 'evil work' anymore...I blame the need to watch internet cats.... Not enough time to concentrate on doing evil well. By selling miners they leverage their assets. The money from selling the miners can be used to build even more miners than they could otherwise. It also hedges their bets by having multiple revenue streams from different sources. I think they know exactly what they are doing.
|
|
|
|
Searing
Copper Member
Legendary
Offline
Activity: 2898
Merit: 1465
Clueless!
|
|
May 10, 2017, 01:52:46 PM |
|
@searing
what power supply do you have for the L3+ or do you have the recommended APW3+ PSU from bitmain?
Just got the bitmain ones at $105 sale that MAY still be on.....it was about $125 I think with shipping. No fuss, no muss had a year warranty...so what the heck
By selling miners they leverage their assets. The money from selling the miners can be used to build even more miners than they could otherwise. It also hedges their bets by having multiple revenue streams from different sources. I think they know exactly what they are doing.
Of that, I have no doubt. Just don't see them 'going full evil thou' ..as in the previous post..don't get it ...just sell hashnet...keep it all?
|
Old Style Legacy Plug & Play BBS System. Get it from www.synchro.net. Updated 1/1/2021. It also works with Windows 10 and likely 11 and allows 16 bit DOS game doors on the same Win 10 Machine in Multi-Node! Five Minute Install! Look it over it uninstalls just as fast, if you simply want to look it over. Freeware! Full BBS System! It is a frigging hoot!:)
|
|
|
MachineZero
Full Member
Offline
Activity: 217
Merit: 100
mcrypt.com domain 4sale 20BTC
|
|
May 10, 2017, 02:36:07 PM |
|
How do the pools setup work? why are there 3? does it switch?
Bitmain has traditionally used a "rollover" setup on pools, so that if pool 0 is down the miner will use pool 1 and if pools 0 and 1 are both down it will use pool 2. They normally autoswitch back to a lower pool number when it comes up, IME with the S5, but it might take several seconds to a minute to do so when it does so. IMO those folks asking $3500 are way high on their price - I could see charging $2000 as a "available now" surcharge but IMO $3500 is a blatant eBay-level ripoff. It generates $55 in LTC a day at the moment. Time is of the essence. Anyone who sells for $2000 now is a fool who can't count.
|
|
|
|
crypticj
|
|
May 10, 2017, 03:06:31 PM |
|
How do the pools setup work? why are there 3? does it switch?
Bitmain has traditionally used a "rollover" setup on pools, so that if pool 0 is down the miner will use pool 1 and if pools 0 and 1 are both down it will use pool 2. They normally autoswitch back to a lower pool number when it comes up, IME with the S5, but it might take several seconds to a minute to do so when it does so. IMO those folks asking $3500 are way high on their price - I could see charging $2000 as a "available now" surcharge but IMO $3500 is a blatant eBay-level ripoff. It generates $55 in LTC a day at the moment. Time is of the essence. Anyone who sells for $2000 now is a fool who can't count. Yeah No one is selling for $2000 if they do please PM me i will buy all you have, even if i have to mortgage my kids [j/k] lol... I think the current rate is around $4k for that machine and thats fair because difficulty will rise for sure and you are looking at around 3-6 months on ROI
|
|
|
|
suchmoon
Legendary
Offline
Activity: 3822
Merit: 9037
https://bpip.org
|
|
May 10, 2017, 06:15:35 PM |
|
Ok, so my Hashnest L3+ purchase wasn't looking very good - I bought them at ~120 LTC each, or ~0.25 LTC per MHS - but for some inexplicable reason it spiked to 0.30 LTC on the market yesterday.
Which allowed me to sell 50% and feel much better about ROI. I'm pretty sure it's a bubble and someone's gonna be left holding the bag, but we're all consenting adults... I hope.
|
|
|
|
wck
Member
Offline
Activity: 70
Merit: 10
|
|
May 10, 2017, 10:24:43 PM |
|
By selling miners they leverage their assets. The money from selling the miners can be used to build even more miners than they could otherwise. It also hedges their bets by having multiple revenue streams from different sources. I think they know exactly what they are doing.
Of that, I have no doubt. Just don't see them 'going full evil thou' ..as in the previous post..don't get it ...just sell hashnet...keep it all? [/quote] We are on the same page, I just misunderstood a previous comment. I agree they don't have any reason to go full evil they are doing very well as it is.
|
|
|
|
MachineZero
Full Member
Offline
Activity: 217
Merit: 100
mcrypt.com domain 4sale 20BTC
|
|
May 11, 2017, 01:50:44 PM |
|
Mined my first block on litecoinpool.org. Two L3+ running for a little over 36hours.
Reward to pool 25LTC pool payouts in the same time 4LTC
Guess it'll even out in the end. Nice to have found a block so fast though.
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
|
May 11, 2017, 02:35:21 PM |
|
So last Friday I hooked up five of these L3+ for hosting, powered off DPS1200 server PSU on my breakout board and nine cables.
Within a couple hours, one of them had set the breakout board on fire. I thought maybe it was a PCB flaw so I replaced it and the melted cables.
So then on Tuesday another board burned up on a different miner. And this morning I came in to find a third board burned up on a third L3+ on another shelf.
The same boards, from the same PCB batch and assembled on the same day, in the same hour, are powering S9 and T9 miners off 1500W PSUs in the hottest part of the hosting room with no problems at all. I've been building breakout boards for over three years and hosting miners for almost as long and had never seen a board burn up before last Friday.
So what the heck is going on with these things?
|
|
|
|
Radientgurkin
|
|
May 11, 2017, 03:23:41 PM |
|
Quick question
Can you point the antminer L3+ to any scrypt pool of your choosing ?
I was told yes. (my L3's and 2 of may 15th L3+'s of 4 ..the rest today ....are mining on www.litecoinpool.org...same as old knc titans that only seem to really,really like the site) But....I know of folk running these on nicehash and other multipools....I'd guess it varies by specific coins mined directly..but have heard they are a lot less picky then my knc titans. I may mine..other coins but at 3150mh of ROI'd Titans and 3550mh (with JULY 1 L3+) .....well hell...but at 30 buck LTC and seg witness not even activated yet that seems a bit 'silly' Litecoin..has been berry,berry good to me...... So have not done much else (or see a lot of will to do so) trying other scrypt pow alts with litecoinpool being free and paying at 103%....and rock stable.....the whim has not moved me yet. (whim...perhaps I should start using the royal 'we' in my conversations......this kicking ass and 30 buck LTC may be going to my head) If you do try mining any of the other coins like Novacoin or Belacoin, please let me know if the miner does it ok. Thanks
|
|
|
|
crypticj
|
|
May 11, 2017, 07:37:16 PM |
|
So last Friday I hooked up five of these L3+ for hosting, powered off DPS1200 server PSU on my breakout board and nine cables.
Within a couple hours, one of them had set the breakout board on fire. I thought maybe it was a PCB flaw so I replaced it and the melted cables.
So then on Tuesday another board burned up on a different miner. And this morning I came in to find a third board burned up on a third L3+ on another shelf.
The same boards, from the same PCB batch and assembled on the same day, in the same hour, are powering S9 and T9 miners off 1500W PSUs in the hottest part of the hosting room with no problems at all. I've been building breakout boards for over three years and hosting miners for almost as long and had never seen a board burn up before last Friday.
So what the heck is going on with these things?
Thats crazy I have used DPS1200 with the X-6 adapter not for L3+ makes me nervous i think i am going to get the recommended AP3+ from bitmain or ebay just to be on the safe side.
|
|
|
|
PsychoticBoy
Donator
Legendary
Offline
Activity: 1890
Merit: 1010
Parental Advisory Explicit Content
|
|
May 11, 2017, 07:44:58 PM |
|
So last Friday I hooked up five of these L3+ for hosting, powered off DPS1200 server PSU on my breakout board and nine cables.
Within a couple hours, one of them had set the breakout board on fire. I thought maybe it was a PCB flaw so I replaced it and the melted cables.
So then on Tuesday another board burned up on a different miner. And this morning I came in to find a third board burned up on a third L3+ on another shelf.
The same boards, from the same PCB batch and assembled on the same day, in the same hour, are powering S9 and T9 miners off 1500W PSUs in the hottest part of the hosting room with no problems at all. I've been building breakout boards for over three years and hosting miners for almost as long and had never seen a board burn up before last Friday.
So what the heck is going on with these things?
Thats crazy I have used DPS1200 with the X-6 adapter not for L3+ makes me nervous i think i am going to get the recommended AP3+ from bitmain or ebay just to be on the safe side. I just use the Bitmain AWP3+, it is convient but the thing makes a lot of noise a very annoying high flute tone, maybe more annoying than the Antminer L3+ it self. 1 or 2 decent ATX PSUs would certainly lower the noise.
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
|
May 11, 2017, 07:49:00 PM |
|
I suspect it'd be less of a problem with a weaker PSU. Since the overcurrent cutoff on the DPS1200 is about 500 watts higher than expected draw on a L3+, if something goes wrong and a hashboard decides to pull 600 watts instead of 200 watts the cables will notice a long time before the PSU does.
Every time I check the supply boards they're running clean and cool. The one burned up last night had been running clean and cool since Friday afternoon. Almost has to be something screwy with the hashboards, but it's been a different miner on a different power supply each time.
Looks like we'll be swapping in 850W supplies with a less generous overcurrent cutoff and see what happens.
Interested to see if anyone else has had issues.
|
|
|
|
Eyedol-X
|
|
May 11, 2017, 08:56:23 PM |
|
I suspect it'd be less of a problem with a weaker PSU. Since the overcurrent cutoff on the DPS1200 is about 500 watts higher than expected draw on a L3+, if something goes wrong and a hashboard decides to pull 600 watts instead of 200 watts the cables will notice a long time before the PSU does.
Every time I check the supply boards they're running clean and cool. The one burned up last night had been running clean and cool since Friday afternoon. Almost has to be something screwy with the hashboards, but it's been a different miner on a different power supply each time.
Looks like we'll be swapping in 850W supplies with a less generous overcurrent cutoff and see what happens.
Interested to see if anyone else has had issues.
No issues here but I'm using a single 1500W PSU on each of mine. I did have one of mine reboot itself for an unexplained reason after 3 days but that's the only thing out of the ordinary so far.
|
|
|
|
edonkey
Legendary
Offline
Activity: 1150
Merit: 1004
|
|
May 11, 2017, 09:00:19 PM |
|
I suspect it'd be less of a problem with a weaker PSU. Since the overcurrent cutoff on the DPS1200 is about 500 watts higher than expected draw on a L3+, if something goes wrong and a hashboard decides to pull 600 watts instead of 200 watts the cables will notice a long time before the PSU does.
Every time I check the supply boards they're running clean and cool. The one burned up last night had been running clean and cool since Friday afternoon. Almost has to be something screwy with the hashboards, but it's been a different miner on a different power supply each time.
Looks like we'll be swapping in 850W supplies with a less generous overcurrent cutoff and see what happens.
Interested to see if anyone else has had issues.
My single L3+ is split between two IBM 2880W Bladecenter PSUs with J4bberwock breakout boards. I split it because I'm already powering two S9s from the same PSUs. Wanted to share the load. I'm on day 2 with no issues (knock on wood). You've got me scared though...
|
Was I helpful? BTC: 3G1Ubof5u8K9iJkM8We2f3amYZgGVdvpHr
|
|
|
jstefanop
Legendary
Offline
Activity: 2162
Merit: 1401
|
|
May 11, 2017, 11:03:02 PM |
|
I suspect it'd be less of a problem with a weaker PSU. Since the overcurrent cutoff on the DPS1200 is about 500 watts higher than expected draw on a L3+, if something goes wrong and a hashboard decides to pull 600 watts instead of 200 watts the cables will notice a long time before the PSU does.
Every time I check the supply boards they're running clean and cool. The one burned up last night had been running clean and cool since Friday afternoon. Almost has to be something screwy with the hashboards, but it's been a different miner on a different power supply each time.
Looks like we'll be swapping in 850W supplies with a less generous overcurrent cutoff and see what happens.
Interested to see if anyone else has had issues.
Was it on stock clocks or were they overclocked? The firmware is supposed to have auto-shutdown if any of the boards get hotter than 80c, so I doubt it was an overheat issue. Either a FET blew on the input rail on one of the boards, or one of the chips in the chain blew.
|
|
|
|
CrazyGuy
Legendary
Offline
Activity: 1973
Merit: 1007
|
|
May 12, 2017, 01:48:09 AM |
|
I've got a couple running as well. I had 1 week without issue then 1 unit tripped my dual corsair 750w unit this morning. Luckily, overcurrent protection kicked in and it only tripped the PSU. No blown chips and it's back up at full speed. My other unit is still running 7 days straight on two IBM DP750w sidehack kits.
|
ASICPuppy.net ASIC Mining Hardware and Accessories - Compac F in stock!
|
|
|
cloh76
|
|
May 12, 2017, 06:35:32 AM |
|
WTF - Bitmain at it again...
953 more L3+ Miners available on Hashnest
3000.0 USD(99.43652635Ł) Each.
|
[ BTC Donations: 13RNJdT72WEd1FsT3CwdJ6jy9NAa7Hsb54 ]
|
|
|
crypticj
|
|
May 12, 2017, 06:37:20 AM |
|
WTF - Bitmain at it again...
953 more L3+ Miners available on Hashnest
3000.0 USD(99.43652635Ł) Each.
Yep they dont' want people to make money who got april and may miners. I spoke with a source in china they are shipping 30000 units almost 15 Th/s worth by July.
|
|
|
|
ErikvanBreen
|
|
May 12, 2017, 06:52:03 AM |
|
WTF - Bitmain at it again...
953 more L3+ Miners available on Hashnest
3000.0 USD(99.43652635Ł) Each.
Wow such greed from Bitmain, glad i sold my miners at around .25LTC/Mhash a few days ago since it crashed down to .2LTC/Mhash instantly after these became available. I expected new miners to come in stock at Hashnest but not at this price
|
|
|
|
|