almirfiorio
|
|
February 10, 2017, 04:15:13 PM |
|
My memory is samsung 8GB DDR3 1600 Core Clocl - 1216 GPU clock - 1750 Voltage are default You need to be more specific here: How did you modify your BIOS, what memory is on your GPU (Hynix/Elpida/Samsung)? What are your other settings aside of mem clock (core clock, core voltage, mem voltage) ? My rig is running at an average of 725 H/s/card (lowest card ~690H/s, fastest ~760H/s) so i can't help you much if your target is to increase the hashrate to 900 H/s :p
|
|
|
|
Maddemon07
Newbie
Offline
Activity: 1
Merit: 0
|
|
February 10, 2017, 04:39:34 PM |
|
I am currently running 2 x R9 Fury Trixx & on Claymore -a 2 mode (low power mode) @ default clocks / no mods each do about ~816 h/s 1632 h/s total, pulling 274 Watts @ the wall. (Mother board pulls ~42w, So each fury is pulling little less than 120watts @ the wall.) I also run a Fury X on my gaming machine, even with the extra shaders doesn't seem to increase the hash rate.. (but more power consumption)
|
|
|
|
almirfiorio
|
|
February 10, 2017, 07:14:24 PM |
|
how did you get this ? I can do more with 2 rx 470? I am currently running 2 x R9 Fury Trixx & on Claymore -a 2 mode (low power mode) @ default clocks / no mods each do about ~816 h/s 1632 h/s total, pulling 274 Watts @ the wall. (Mother board pulls ~42w, So each fury is pulling little less than 120watts @ the wall.) I also run a Fury X on my gaming machine, even with the extra shaders doesn't seem to increase the hash rate.. (but more power consumption)
|
|
|
|
ol92
|
|
February 10, 2017, 10:32:06 PM |
|
[R9 FURY speeds]
about 400H/s from sinlge grphic card, is it normal? Quite insanse. Double lower than polaris.
Yeah I get less than 500 with my fury on claymore. use another xmr miner, you'll get around 800. But its mining Zec anyway. I havent played with it for xmr, but i'm quite positive it can do more. I wonder if w0lf has a fury. There are private miners out there too. I got 880h/s with a fury-x gpu@1125mhz with claymore 9.6. Try with -h 1024. Driver between 15.12 and 16.11
|
|
|
|
rinus
|
|
February 11, 2017, 10:36:53 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
|
|
|
|
avirdoz
Legendary
Offline
Activity: 1191
Merit: 1001
|
|
February 11, 2017, 10:44:13 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm.
|
|
|
|
rinus
|
|
February 11, 2017, 11:05:27 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm. I have 6 cards sapphire rx480 8 giga. No minergate?
|
|
|
|
Hurtman
|
|
February 11, 2017, 11:35:32 PM |
|
sgminer not a better , claymore still much better
|
|
|
|
drr0ss
Member
Offline
Activity: 98
Merit: 10
|
|
February 14, 2017, 11:02:51 AM |
|
Hey Claymore, do you plan to implement assembler features to the rest of your miners, and when [ ]?
|
|
|
|
newmz
Sr. Member
Offline
Activity: 372
Merit: 250
The road of excess leads to the palace of wisdom
|
|
February 14, 2017, 11:47:42 AM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm. I had a lot of problems trying to run sgminer-gm so I stuck to claymore. I have 2 win 7 x64 rigs with 15.12 drivers, and both rigs are mostly 290s or 290Xs, but each rig also has 1 380 on it. I think sgminer-gm didn't like either the 15.12 drivers or the fact that I didn't have all the same GPUs on each rig. Claymore "just works". Sgminer-gm seems to require quite a bit of skill in setting different parameters and I found it confusing and read conflicting information about how best to define the parameters. If I could spend more time learning to use sgminer-gm I would love to try it but as I said - I found it difficult to set up correctly. Do you have any suggestions about where to learn how to use sgminer-gm properly?
|
Crypto currency enthusiast and miner since 2015. Mined approx 200 ETH during 2016 and 2017 and sold it at approximately $US40 each. Then I watched it reach $1000+ each. If anyone bothers to read this stuff pay attention to this: HODL HODL HODL HODL HODL HODL
I started mining with 1 AMD 7950 and 1 R9-280X. Then I gradually built my AMD operation into 12 R9-290s. Awesome ETH hash but ridiculous power consumption and heat. Over the last year I defected to the Nvidia team. I now use GTX 1070s. They were expensive to buy (probably a bargain now) but awesome hash rate vs. power consumption. blah blah blah blah
|
|
|
JuanHungLo
|
|
February 14, 2017, 12:32:38 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm. I had a lot of problems trying to run sgminer-gm so I stuck to claymore. I have 2 win 7 x64 rigs with 15.12 drivers, and both rigs are mostly 290s or 290Xs, but each rig also has 1 380 on it. I think sgminer-gm didn't like either the 15.12 drivers or the fact that I didn't have all the same GPUs on each rig. Claymore "just works". Sgminer-gm seems to require quite a bit of skill in setting different parameters and I found it confusing and read conflicting information about how best to define the parameters. If I could spend more time learning to use sgminer-gm I would love to try it but as I said - I found it difficult to set up correctly. Do you have any suggestions about where to learn how to use sgminer-gm properly? You assumption about 15.12 is correct. Use AMD drivers 16.9.2 or higher. The following works for 380x: set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_MAX_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_MAX_SINGLE_ALLOC_PERCENT 100 sgminer -k cryptonight -o stratum+tcp://monerohash.com:7777 -u ADDRESS -p x --rawintensity 512 -w 4 -g 2 --gpu-engine 1040 --gpu-memclock 1625 --auto-fan --temp-target 80 --no-submit-stale --no-extranonce With my modded 380x I get 730 h/s. Can't speak for 290. But for 280x:--rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 Both yields better than the CM miner. Sorry, Claymore, I've always used your miners but you've been passed up.
|
Bull markets are born on pessimism, grow on skepticism, mature on optimism, and die on euphoria. - John Templeton
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
|
February 14, 2017, 01:53:06 PM |
|
Hi Claymore...
A humble request.
Can you get the v9.7 ported to Linux?
Thanks
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
batko
|
|
February 14, 2017, 02:30:43 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm. I had a lot of problems trying to run sgminer-gm so I stuck to claymore. I have 2 win 7 x64 rigs with 15.12 drivers, and both rigs are mostly 290s or 290Xs, but each rig also has 1 380 on it. I think sgminer-gm didn't like either the 15.12 drivers or the fact that I didn't have all the same GPUs on each rig. Claymore "just works". Sgminer-gm seems to require quite a bit of skill in setting different parameters and I found it confusing and read conflicting information about how best to define the parameters. If I could spend more time learning to use sgminer-gm I would love to try it but as I said - I found it difficult to set up correctly. Do you have any suggestions about where to learn how to use sgminer-gm properly? You assumption about 15.12 is correct. Use AMD drivers 16.9.2 or higher. The following works for 380x: set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_MAX_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_MAX_SINGLE_ALLOC_PERCENT 100 sgminer -k cryptonight -o stratum+tcp://monerohash.com:7777 -u ADDRESS -p x --rawintensity 512 -w 4 -g 2 --gpu-engine 1040 --gpu-memclock 1625 --auto-fan --temp-target 80 --no-submit-stale --no-extranonce With my modded 380x I get 730 h/s. Can't speak for 290. But for 280x:--rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 Both yields better than the CM miner. Sorry, Claymore, I've always used your miners but you've been passed up. You have good bios for R9 380x whats results for 280x? --rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 ?
|
Donation: ETH: 0x0c8ce94dd3d1bfd09c0f887559c61d1b551e4b4d
|
|
|
dnox
Newbie
Offline
Activity: 16
Merit: 0
|
|
February 14, 2017, 04:03:23 PM |
|
Hello, im actually having some trouble using claymore. I have a AMD Radeon 5800 and installed claymore to mine with my gpu. Im also using minergate miner to CPU mine. But claymore is being responsible for 4 invalid shares in less than 24hs and this gave me a negative balance. At first i tought it could be the heat since claymore was showing 80C on my gpu. I set -tt to 50 and -fanmax to 100 and this solved the temperature problem, its now running at 60C. But even after fixing the cooling i got another invalid share and had to turn off claymore because it was making me lose money. Is it because my GPU is an old model? Is there anyway i can fix it?
Thnx a lot in advance.
|
|
|
|
JuanHungLo
|
|
February 14, 2017, 04:41:58 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm. I had a lot of problems trying to run sgminer-gm so I stuck to claymore. I have 2 win 7 x64 rigs with 15.12 drivers, and both rigs are mostly 290s or 290Xs, but each rig also has 1 380 on it. I think sgminer-gm didn't like either the 15.12 drivers or the fact that I didn't have all the same GPUs on each rig. Claymore "just works". Sgminer-gm seems to require quite a bit of skill in setting different parameters and I found it confusing and read conflicting information about how best to define the parameters. If I could spend more time learning to use sgminer-gm I would love to try it but as I said - I found it difficult to set up correctly. Do you have any suggestions about where to learn how to use sgminer-gm properly? You assumption about 15.12 is correct. Use AMD drivers 16.9.2 or higher. The following works for 380x: set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_MAX_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_MAX_SINGLE_ALLOC_PERCENT 100 sgminer -k cryptonight -o stratum+tcp://monerohash.com:7777 -u ADDRESS -p x --rawintensity 512 -w 4 -g 2 --gpu-engine 1040 --gpu-memclock 1625 --auto-fan --temp-target 80 --no-submit-stale --no-extranonce With my modded 380x I get 730 h/s. Can't speak for 290. But for 280x:--rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 Both yields better than the CM miner. Sorry, Claymore, I've always used your miners but you've been passed up. You have good bios for R9 380x whats results for 280x? --rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 ? It varies depending on card: Gigabyte at 1100/1550 elpida does 578, 1100/1500 hynix does 565 Sapphire Hynix, and XFX elpida 1050/1500 does 563 with sgminer all stable, no HW errors less than .2% rejects.
|
Bull markets are born on pessimism, grow on skepticism, mature on optimism, and die on euphoria. - John Templeton
|
|
|
batko
|
|
February 14, 2017, 06:02:23 PM |
|
with sapphire 280x hynix AFR I have 640Hs 1100/1625 mod bios, Sapphire 280x Elpida BBBg 605Hs same clock mod bios.
|
Donation: ETH: 0x0c8ce94dd3d1bfd09c0f887559c61d1b551e4b4d
|
|
|
carlo_0000
Legendary
Offline
Activity: 1281
Merit: 1003
|
|
February 14, 2017, 07:35:36 PM |
|
Hey guys
What miner should I use? Is minergate any good? Is it slower? Are fees higher ? I have no idea what is the difference. Help is much appreciated
For 2 gb cards claymore's, for 4gb and more better sgminer-gm. I had a lot of problems trying to run sgminer-gm so I stuck to claymore. I have 2 win 7 x64 rigs with 15.12 drivers, and both rigs are mostly 290s or 290Xs, but each rig also has 1 380 on it. I think sgminer-gm didn't like either the 15.12 drivers or the fact that I didn't have all the same GPUs on each rig. Claymore "just works". Sgminer-gm seems to require quite a bit of skill in setting different parameters and I found it confusing and read conflicting information about how best to define the parameters. If I could spend more time learning to use sgminer-gm I would love to try it but as I said - I found it difficult to set up correctly. Do you have any suggestions about where to learn how to use sgminer-gm properly? You assumption about 15.12 is correct. Use AMD drivers 16.9.2 or higher. The following works for 380x: set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_MAX_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_MAX_SINGLE_ALLOC_PERCENT 100 sgminer -k cryptonight -o stratum+tcp://monerohash.com:7777 -u ADDRESS -p x --rawintensity 512 -w 4 -g 2 --gpu-engine 1040 --gpu-memclock 1625 --auto-fan --temp-target 80 --no-submit-stale --no-extranonce With my modded 380x I get 730 h/s. Can't speak for 290. But for 280x:--rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 Both yields better than the CM miner. Sorry, Claymore, I've always used your miners but you've been passed up. You have good bios for R9 380x whats results for 280x? --rawintensity 896 -w 8 -g 1 --gpu-engine 1070 --gpu-memclock 1550 ? It varies depending on card: Gigabyte at 1100/1550 elpida does 578, 1100/1500 hynix does 565 Sapphire Hynix, and XFX elpida 1050/1500 does 563 with sgminer all stable, no HW errors less than .2% rejects. heu strange with my 380 2gigas version not x, i do 600 with asus , xfx 619 and sapphire 622 with original bios and default clock (oc not stable and useless for little h/s)
|
|
|
|
mrtrodonet
Newbie
Offline
Activity: 14
Merit: 0
|
|
February 15, 2017, 04:41:35 AM |
|
I'm seeing a very weird behavior with my MSI 8gb rx480s. I started a miner and got stable 750h/s at 1350/2250 After reboot i started the miner again and it gives me 480 h/s now. Restarted miner and get 300h/s Restarted a few more times and back to 480h/s
I'm using MSI afterburber on win10. I killed wattman process. Card is using 100% power and seems to be running at set clock speeds.
Config: -a 4 -h 1024 set virtual memory to 16gb-20gb before running the miner i run: setx GPU_MAX_ALLOC_PERCENT 100
Any ideas?
|
|
|
|
carlo_0000
Legendary
Offline
Activity: 1281
Merit: 1003
|
|
February 15, 2017, 05:53:53 PM |
|
i have that too with my 5x 470's they run average 760hs but 1 or 2 of them run in the 400-500's
i have to restart the miner a lot of time and change a bit clock setting till they all hit 750+ than i reset my clock to 1920
|
|
|
|
sorry2xs
Legendary
Offline
Activity: 924
Merit: 1000
Dark Passenger Bitcoin miner 2013,Bitcoin node
|
|
February 16, 2017, 01:38:46 AM |
|
is the a way to change the color for devfee mining
|
Please tip the Node 1MPWKB23NsZsXHANnFwVAWT86mL24fqAjF; KO4UX THAT NO GOOD DO GOODER BAT!!!
|
|
|
|