philipma1957
Legendary
 Online
Activity: 4298
Merit: 8804
'The right to privacy matters'
|
 |
January 02, 2015, 11:48:26 PM |
|
Hello all. This is my first post but I have been lurking for a while. I was wondering if anyone had any insight on this. I ordered 2 S3s from cryptocrane. They arrived in a timely fashion and in good condition. When I got them all I had was an old 600 watt psu. I plugged the one miner into it and before I could configure it, the psu blew. I figured it was old so had to be psu. Ordered a 750 watt psu thinking that would run both. Plugged the same miner in and it blew that one. Okay, strange. This time I got slick (or so I thought) and ordered 2 1000 watt psus. Plugged the same miner in that blew the last 2 and pop, third one. Okay definitely a bad unit. Plug the other one in and I'll be damned, it blew the other psu. That is more than a coincidence. Any ideas? just bad luck or bad units? So far I'm out 120 bucks cause I opened the 2 1000s. Very frustrating to say the least. I then got a gtxa 1000 watt g1, now one miner's (the second one) fan comes on but nothing else, no led lights nothing. The other one (the first one) does nothing at all.
sounds like you fucked up. not to blame you for bad s-3's ,but one blown psu is all you are supposed to do before you post for help. At this point you claim you killed 4 psu's 3 on the same unit and the fourth psu on the other unit. So most people here won't be very helpful. I would be afraid to give you any advice since your procedure on trouble shooting so far was terrible. I don't know what to think about your skill set with pc gear, or if you are a shill that opened the account today just to attack bitmaintech. |
|
|
|
swilla
Member
 Offline
Activity: 77
Merit: 10
|
|
January 03, 2015, 12:25:31 AM
Last edit: January 03, 2015, 12:37:54 AM by swilla |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good. (just look at yours)
|
|
|
|
|
|
1Neptune
|
|
January 03, 2015, 12:40:11 AM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good.
It looks like you didn't post the brand name or manufacturer of the power supplies. That can make a huge difference in getting help and identifying the problem. You need to see if the power supplies will work without any load on them. Use the paper clip in the motherboard connector method (examples abound, do a search for the details) and see if the power supplies power on at all anymore. If they do, use a voltmeter to see if it produces 12v on the required pins in the different connectors. Also look at the specs for the power supplies to see if the 12v supplied is on a single or multiple rails. You need single rail. Cheaper power supplies generally are multiple rail which will cause you problems. After you determine if the power supplies will power on at all, then open the S3's and see if there are any obvious burned components or traces on the printed circuit boards. It sounds like the power supply leads/traces may be fused into a short and that may have popped/trashed your power supplies. If there is any obvious internal damage open a support request with bitmaintech and work with them to see if it's a warranty repair or replacement situation. Just a word for the future: you're spending lots of money on a piece of equipment... don't scrimp on the power supply to run it, especially when sellers such as newegg.com have perfectly functional power supplies for reasonable prices and frequently offer rebate or discounts that make the power supplies even more reasonable in price. Look for at least a 500 watt power supply with the 12v on a SINGLE rail, not multiple. For a comfort margin and to operate the power supplies more efficiently, you may want to get a minimum 600 watt power supply. Just as a personal preference, one power supply per miner and I generally use CX500's or CX600's or even CX750's, but not the modular power supplies (they generally have 1 pci-e connector and you need 2 or more if over clocking). If you power multiple miners off a larger power supply and it tanks, you have multiple miners out of service. |
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
January 03, 2015, 12:58:25 AM |
|
Hello all. This is my first post but I have been lurking for a while. I was wondering if anyone had any insight on this. I ordered 2 S3s from cryptocrane. They arrived in a timely fashion and in good condition. When I got them all I had was an old 600 watt psu. I plugged the one miner into it and before I could configure it, the psu blew. I figured it was old so had to be psu. Ordered a 750 watt psu thinking that would run both. Plugged the same miner in and it blew that one. Okay, strange. This time I got slick (or so I thought) and ordered 2 1000 watt psus. Plugged the same miner in that blew the last 2 and pop, third one. Okay definitely a bad unit. Plug the other one in and I'll be damned, it blew the other psu. That is more than a coincidence. Any ideas? just bad luck or bad units? So far I'm out 120 bucks cause I opened the 2 1000s. Very frustrating to say the least. I then got a gtxa 1000 watt g1, now one miner's (the second one) fan comes on but nothing else, no led lights nothing. The other one (the first one) does nothing at all.
i want to know where you ordered 2 1000w psus for 120$.. lol.. im thinking this could be your problem.. |
|
|
|
|
swilla
Member
Offline
Activity: 77
Merit: 10
|
|
January 03, 2015, 01:05:47 AM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good.
It looks like you didn't post the brand name or manufacturer of the power supplies. That can make a huge difference in getting help and identifying the problem. You need to see if the power supplies will work without any load on them. Use the paper clip in the motherboard connector method (examples abound, do a search for the details) and see if the power supplies power on at all anymore. If they do, use a voltmeter to see if it produces 12v on the required pins in the different connectors. Also look at the specs for the power supplies to see if the 12v supplied is on a single or multiple rails. You need single rail. Cheaper power supplies generally are multiple rail which will cause you problems. After you determine if the power supplies will power on at all, then open the S3's and see if there are any obvious burned components or traces on the printed circuit boards. It sounds like the power supply leads/traces may be fused into a short and that may have popped/trashed your power supplies. If there is any obvious internal damage open a support request with bitmaintech and work with them to see if it's a warranty repair or replacement situation. Just a word for the future: you're spending lots of money on a piece of equipment... don't scrimp on the power supply to run it, especially when sellers such as newegg.com have perfectly functional power supplies for reasonable prices and frequently offer rebate or discounts that make the power supplies even more reasonable in price. Look for at least a 500 watt power supply with the 12v on a SINGLE rail, not multiple. For a comfort margin and to operate the power supplies more efficiently, you may want to get a minimum 600 watt power supply. Just as a personal preference, one power supply per miner and I generally use CX500's or CX600's or even CX750's, but not the modular power supplies (they generally have 1 pci-e connector and you need 2 or more if over clocking). If you power multiple miners off a larger power supply and it tanks, you have multiple miners out of service. Yes I'm aware of this. The first 1 was a power supply claimed from an ancient computer. The 750 was a CHIEF MAX 750. I returned that. The 1000s were Kentek. I am not sure what happened to the first, it just smoked and stopped. But the fuse was good. The second one blew a fuse, so I unsoldered the good fuse but that went as soon as I plugged in with no load. So those ones are no good at all until I can get new fuses for them. As far as opening the cases, I did that and everything looks fine. Nothing visually wrong at all. I even went as far at to test for continuity in all the cables, very tedious. As far a Bitmain I am in contact with them. But progress is slow. I now have a modular PSU so each blade gets it's own rail. Also, The one that blew the three got so hot there's still pieces of the pin glued to the connector. I tried using both controllers in each miner and the results were the same. Nothing. I'm not sure if I should be asking for new boards or whole new units. I just want to mine some coin! |
|
|
|
|
|
1Neptune
|
|
January 03, 2015, 04:06:15 AM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good.
It looks like you didn't post the brand name or manufacturer of the power supplies. That can make a huge difference in getting help and identifying the problem. You need to see if the power supplies will work without any load on them. Use the paper clip in the motherboard connector method (examples abound, do a search for the details) and see if the power supplies power on at all anymore. If they do, use a voltmeter to see if it produces 12v on the required pins in the different connectors. Also look at the specs for the power supplies to see if the 12v supplied is on a single or multiple rails. You need single rail. Cheaper power supplies generally are multiple rail which will cause you problems. After you determine if the power supplies will power on at all, then open the S3's and see if there are any obvious burned components or traces on the printed circuit boards. It sounds like the power supply leads/traces may be fused into a short and that may have popped/trashed your power supplies. If there is any obvious internal damage open a support request with bitmaintech and work with them to see if it's a warranty repair or replacement situation. Just a word for the future: you're spending lots of money on a piece of equipment... don't scrimp on the power supply to run it, especially when sellers such as newegg.com have perfectly functional power supplies for reasonable prices and frequently offer rebate or discounts that make the power supplies even more reasonable in price. Look for at least a 500 watt power supply with the 12v on a SINGLE rail, not multiple. For a comfort margin and to operate the power supplies more efficiently, you may want to get a minimum 600 watt power supply. Just as a personal preference, one power supply per miner and I generally use CX500's or CX600's or even CX750's, but not the modular power supplies (they generally have 1 pci-e connector and you need 2 or more if over clocking). If you power multiple miners off a larger power supply and it tanks, you have multiple miners out of service. Yes I'm aware of this. The first 1 was a power supply claimed from an ancient computer. The 750 was a CHIEF MAX 750. I returned that. The 1000s were Kentek. I am not sure what happened to the first, it just smoked and stopped. But the fuse was good. The second one blew a fuse, so I unsoldered the good fuse but that went as soon as I plugged in with no load. So those ones are no good at all until I can get new fuses for them. As far as opening the cases, I did that and everything looks fine. Nothing visually wrong at all. I even went as far at to test for continuity in all the cables, very tedious. As far a Bitmain I am in contact with them. But progress is slow. I now have a modular PSU so each blade gets it's own rail. Also, The one that blew the three got so hot there's still pieces of the pin glued to the connector. I tried using both controllers in each miner and the results were the same. Nothing. I'm not sure if I should be asking for new boards or whole new units. I just want to mine some coin! Hmmm. I wouldn't be using any of the power supplies you've noted. As to the miners themselves, this is probably the first instance of power connectors melting on the miner unit itself. I've not read any postings saying so, but of course I've not read every posting in bitcointalk either. I'd suggest working to get replacement units. Something overheating very badly caused the miners power connectors to melt. Bitmain should be interested in the forensics result on this one. |
|
|
|
|
swilla
Member
Offline
Activity: 77
Merit: 10
|
|
January 03, 2015, 04:18:58 AM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good.
It looks like you didn't post the brand name or manufacturer of the power supplies. That can make a huge difference in getting help and identifying the problem. You need to see if the power supplies will work without any load on them. Use the paper clip in the motherboard connector method (examples abound, do a search for the details) and see if the power supplies power on at all anymore. If they do, use a voltmeter to see if it produces 12v on the required pins in the different connectors. Also look at the specs for the power supplies to see if the 12v supplied is on a single or multiple rails. You need single rail. Cheaper power supplies generally are multiple rail which will cause you problems. After you determine if the power supplies will power on at all, then open the S3's and see if there are any obvious burned components or traces on the printed circuit boards. It sounds like the power supply leads/traces may be fused into a short and that may have popped/trashed your power supplies. If there is any obvious internal damage open a support request with bitmaintech and work with them to see if it's a warranty repair or replacement situation. Just a word for the future: you're spending lots of money on a piece of equipment... don't scrimp on the power supply to run it, especially when sellers such as newegg.com have perfectly functional power supplies for reasonable prices and frequently offer rebate or discounts that make the power supplies even more reasonable in price. Look for at least a 500 watt power supply with the 12v on a SINGLE rail, not multiple. For a comfort margin and to operate the power supplies more efficiently, you may want to get a minimum 600 watt power supply. Just as a personal preference, one power supply per miner and I generally use CX500's or CX600's or even CX750's, but not the modular power supplies (they generally have 1 pci-e connector and you need 2 or more if over clocking). If you power multiple miners off a larger power supply and it tanks, you have multiple miners out of service. Yes I'm aware of this. The first 1 was a power supply claimed from an ancient computer. The 750 was a CHIEF MAX 750. I returned that. The 1000s were Kentek. I am not sure what happened to the first, it just smoked and stopped. But the fuse was good. The second one blew a fuse, so I unsoldered the good fuse but that went as soon as I plugged in with no load. So those ones are no good at all until I can get new fuses for them. As far as opening the cases, I did that and everything looks fine. Nothing visually wrong at all. I even went as far at to test for continuity in all the cables, very tedious. As far a Bitmain I am in contact with them. But progress is slow. I now have a modular PSU so each blade gets it's own rail. Also, The one that blew the three got so hot there's still pieces of the pin glued to the connector. I tried using both controllers in each miner and the results were the same. Nothing. I'm not sure if I should be asking for new boards or whole new units. I just want to mine some coin! Hmmm. I wouldn't be using any of the power supplies you've noted. As to the miners themselves, this is probably the first instance of power connectors melting on the miner unit itself. I've not read any postings saying so, but of course I've not read every posting in bitcointalk either. I'd suggest working to get replacement units. Something overheating very badly caused the miners power connectors to melt. Bitmain should be interested in the forensics result on this one. Sorry.. Should read connector glued to pin |
|
|
|
|
Nite
Newbie
Offline
Activity: 51
Merit: 0
|
|
January 03, 2015, 04:34:45 AM |
|
if the fuses are blowing that easy, my guess is the wall violtage, are you sure you aren't use a 110v unit on a 220 plug? I know some parts of the world have to use 220 for power on everything, where as those in USA can use 110 and 220
|
|
|
|
|
|
grn
|
|
January 03, 2015, 04:38:15 AM |
|
Hello all. This is my first post but I have been lurking for a while. I was wondering if anyone had any insight on this. I ordered 2 S3s from cryptocrane. They arrived in a timely fashion and in good condition. When I got them all I had was an old 600 watt psu. I plugged the one miner into it and before I could configure it, the psu blew. I figured it was old so had to be psu. Ordered a 750 watt psu thinking that would run both. Plugged the same miner in and it blew that one. Okay, strange. This time I got slick (or so I thought) and ordered 2 1000 watt psus. Plugged the same miner in that blew the last 2 and pop, third one. Okay definitely a bad unit. Plug the other one in and I'll be damned, it blew the other psu. That is more than a coincidence. Any ideas? just bad luck or bad units? So far I'm out 120 bucks cause I opened the 2 1000s. Very frustrating to say the least. I then got a evga 1000 watt g1, now one miner's (the second one) fan comes on but nothing else, no led lights nothing. The other one (the first one) does nothing at all.
have you contacted cryptocrane? They did sell you the miners at a premium so they should provide after sales service. |
How is that Lexical analysis working out bickneleski?
|
|
|
dogie
Legendary
Offline
Activity: 1666
Merit: 1185
dogiecoin.com
|
|
January 03, 2015, 10:40:51 AM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good.
It looks like you didn't post the brand name or manufacturer of the power supplies. That can make a huge difference in getting help and identifying the problem. You need to see if the power supplies will work without any load on them. Use the paper clip in the motherboard connector method (examples abound, do a search for the details) and see if the power supplies power on at all anymore. If they do, use a voltmeter to see if it produces 12v on the required pins in the different connectors. Also look at the specs for the power supplies to see if the 12v supplied is on a single or multiple rails. You need single rail. Cheaper power supplies generally are multiple rail which will cause you problems. After you determine if the power supplies will power on at all, then open the S3's and see if there are any obvious burned components or traces on the printed circuit boards. It sounds like the power supply leads/traces may be fused into a short and that may have popped/trashed your power supplies. If there is any obvious internal damage open a support request with bitmaintech and work with them to see if it's a warranty repair or replacement situation. Just a word for the future: you're spending lots of money on a piece of equipment... don't scrimp on the power supply to run it, especially when sellers such as newegg.com have perfectly functional power supplies for reasonable prices and frequently offer rebate or discounts that make the power supplies even more reasonable in price. Look for at least a 500 watt power supply with the 12v on a SINGLE rail, not multiple. For a comfort margin and to operate the power supplies more efficiently, you may want to get a minimum 600 watt power supply. Just as a personal preference, one power supply per miner and I generally use CX500's or CX600's or even CX750's, but not the modular power supplies (they generally have 1 pci-e connector and you need 2 or more if over clocking). If you power multiple miners off a larger power supply and it tanks, you have multiple miners out of service. Yes I'm aware of this. The first 1 was a power supply claimed from an ancient computer. The 750 was a CHIEF MAX 750. I returned that. The 1000s were Kentek. I am not sure what happened to the first, it just smoked and stopped. But the fuse was good. The second one blew a fuse, so I unsoldered the good fuse but that went as soon as I plugged in with no load. So those ones are no good at all until I can get new fuses for them. As far as opening the cases, I did that and everything looks fine. Nothing visually wrong at all. I even went as far at to test for continuity in all the cables, very tedious. As far a Bitmain I am in contact with them. But progress is slow. I now have a modular PSU so each blade gets it's own rail. Also, The one that blew the three got so hot there's still pieces of the pin glued to the connector. I tried using both controllers in each miner and the results were the same. Nothing. I'm not sure if I should be asking for new boards or whole new units. I just want to mine some coin! Can you link to the exact 1000W PSUs you used please? |
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
January 03, 2015, 12:03:14 PM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good.
It looks like you didn't post the brand name or manufacturer of the power supplies. That can make a huge difference in getting help and identifying the problem. You need to see if the power supplies will work without any load on them. Use the paper clip in the motherboard connector method (examples abound, do a search for the details) and see if the power supplies power on at all anymore. If they do, use a voltmeter to see if it produces 12v on the required pins in the different connectors. Also look at the specs for the power supplies to see if the 12v supplied is on a single or multiple rails. You need single rail. Cheaper power supplies generally are multiple rail which will cause you problems. After you determine if the power supplies will power on at all, then open the S3's and see if there are any obvious burned components or traces on the printed circuit boards. It sounds like the power supply leads/traces may be fused into a short and that may have popped/trashed your power supplies. If there is any obvious internal damage open a support request with bitmaintech and work with them to see if it's a warranty repair or replacement situation. Just a word for the future: you're spending lots of money on a piece of equipment... don't scrimp on the power supply to run it, especially when sellers such as newegg.com have perfectly functional power supplies for reasonable prices and frequently offer rebate or discounts that make the power supplies even more reasonable in price. Look for at least a 500 watt power supply with the 12v on a SINGLE rail, not multiple. For a comfort margin and to operate the power supplies more efficiently, you may want to get a minimum 600 watt power supply. Just as a personal preference, one power supply per miner and I generally use CX500's or CX600's or even CX750's, but not the modular power supplies (they generally have 1 pci-e connector and you need 2 or more if over clocking). If you power multiple miners off a larger power supply and it tanks, you have multiple miners out of service. Yes I'm aware of this. The first 1 was a power supply claimed from an ancient computer. The 750 was a CHIEF MAX 750. I returned that. The 1000s were Kentek. I am not sure what happened to the first, it just smoked and stopped. But the fuse was good. The second one blew a fuse, so I unsoldered the good fuse but that went as soon as I plugged in with no load. So those ones are no good at all until I can get new fuses for them. As far as opening the cases, I did that and everything looks fine. Nothing visually wrong at all. I even went as far at to test for continuity in all the cables, very tedious. As far a Bitmain I am in contact with them. But progress is slow. I now have a modular PSU so each blade gets it's own rail. Also, The one that blew the three got so hot there's still pieces of the pin glued to the connector. I tried using both controllers in each miner and the results were the same. Nothing. I'm not sure if I should be asking for new boards or whole new units. I just want to mine some coin! Can you link to the exact 1000W PSUs you used please? it looks like he used this one.. http://www.amazon.com/KENTEK-Supply-EPS12V-SLI-ready-PCI-Express/dp/B00596TJU2/ref=sr_1_4?s=electronics&ie=UTF8&qid=1420286116&sr=1-4&keywords=KENTEKvery poor rating, not even 80+ has 2 12v rails rated at only 35A, so if he plugged the 2 miners into the pci-e slots he overloaded the psu as soon as it powered on. |
|
|
|
|
philipma1957
Legendary
Online
Activity: 4298
Merit: 8804
'The right to privacy matters'
|
|
January 03, 2015, 01:27:14 PM |
|
Not trying to attack bitmain at all. I did a lot of research before buying, and they had the reviews I liked. As far as my troubleshooting, you sound like my buddy. He said I just got unlucky and got bum units. Me being the optimist was hoping it was because I was trying to be cheap on PSUs. As far as asking for advise after 1st one I've read the responses most have and figured that wouldn't do me any good. (just look at yours)
no you did not do a lot of research on the psu end. if you did you would not have purchased or used terrible psu's. you simply would have looked for a sale on this psu http://www.amazon.com/EVGA-SuperNOVA-1300G2-ATX12V-120-G2-1300-XR/dp/B00COIZTZM/ref=sr_1_1?ie=UTF8&qid=1420291560&sr=8-1&keywords=evga+1300+g2it can run 3 s-3's has a ten year warranty and just about everyone here swears by it as one of the best psu's for mining. |
|
|
|
|
taaku
|
|
January 03, 2015, 02:27:17 PM |
|
i have s3 miner which is connected to internet and i am able to access through default IP 192.168.1.99 but its not hashing..i have correct pool and the pool is connected..but in miner status page its not hashing its shows as zero... i have tried to reset the machine but its same .Attached is the screenshot.  |
BTC: 1DgUj6s1yRwauEb89mGn92ZfNqK8xwcZPP
|
|
|
|
pekatete
|
|
January 03, 2015, 02:32:02 PM |
|
i have s3 miner which is connected to internet and i am able to access through default IP 192.168.1.99 but its not hashing..i have correct pool and the pool is connected..but in miner status page its not hashing its shows as zero...
i have tried to reset the machine but its same .Attached is the screenshot.
<snip> img </snip>
Go to Network tab then click edit on your connection then switch the protocol to DHCP and Save & Apply. You'll get a new IP address, so it will not be on 192.168.1.99 anymore, but will begin hashing straight away. |
|
|
|
|
taaku
|
|
January 03, 2015, 02:38:29 PM |
|
i have s3 miner which is connected to internet and i am able to access through default IP 192.168.1.99 but its not hashing..i have correct pool and the pool is connected..but in miner status page its not hashing its shows as zero...
i have tried to reset the machine but its same .Attached is the screenshot.
<snip> img </snip>
Go to Network tab then click edit on your connection then switch the protocol to DHCP and Save & Apply. You'll get a new IP address, so it will not be on 192.168.1.99 anymore, but will begin hashing straight away. yes i tried that but even then its not hashing..now the network have assigned it a value 192.168.1.100...  |
BTC: 1DgUj6s1yRwauEb89mGn92ZfNqK8xwcZPP
|
|
|
philipma1957
Legendary
Online
Activity: 4298
Merit: 8804
'The right to privacy matters'
|
|
January 03, 2015, 02:40:50 PM |
|
i have s3 miner which is connected to internet and i am able to access through default IP 192.168.1.99 but its not hashing..i have correct pool and the pool is connected..but in miner status page its not hashing its shows as zero...
i have tried to reset the machine but its same .Attached is the screenshot.
<snip> img </snip>
Go to Network tab then click edit on your connection then switch the protocol to DHCP and Save & Apply. You'll get a new IP address, so it will not be on 192.168.1.99 anymore, but will begin hashing straight away. yes i tried that but even then its not hashing..now the network have assigned it a value 192.168.1.100... 12 seconds into startup wait for 5 minutes. if it still shows 0 post a screen shot |
|
|
|
|
taaku
|
|
January 03, 2015, 02:45:36 PM |
|
i have s3 miner which is connected to internet and i am able to access through default IP 192.168.1.99 but its not hashing..i have correct pool and the pool is connected..but in miner status page its not hashing its shows as zero...
i have tried to reset the machine but its same .Attached is the screenshot.
<snip> img </snip>
Go to Network tab then click edit on your connection then switch the protocol to DHCP and Save & Apply. You'll get a new IP address, so it will not be on 192.168.1.99 anymore, but will begin hashing straight away. yes i tried that but even then its not hashing..now the network have assigned it a value 192.168.1.100... 12 seconds into startup wait for 5 minutes. if it still shows 0 post a screen shot its same after 5 mins also..after some time its restarts..but the values is never shown greater then 0.  |
BTC: 1DgUj6s1yRwauEb89mGn92ZfNqK8xwcZPP
|
|
|
tZKtdvt6
Full Member
Offline
Activity: 166
Merit: 100
Developer
|
|
January 03, 2015, 02:47:14 PM |
|
 Smooth and precise as a Swiss clock. Here you can see the antminer S3+ working, it is very funny. The antminer s3+ has the cgminer updated to the date: 20-Oct-2014 02:13 Thank you very much. |
|
|
|
|
pekatete
|
|
January 03, 2015, 02:50:47 PM |
|
<snip> img </snip>
Smooth and precise as a Swiss clock.
Here you can see the antminer S3+ working, it is very funny.
The antminer s3+ has the cgminer updated to the date: 20-Oct-2014 02:13
Thank you very much.
I admire you for running an antic firmware! But yeah, if it ain't broke, don't fix it! Nevertheless, you may do better with the December 19th firmware ... at your risk. |
|
|
|
|
pekatete
|
|
January 03, 2015, 02:51:33 PM |
|
i have s3 miner which is connected to internet and i am able to access through default IP 192.168.1.99 but its not hashing..i have correct pool and the pool is connected..but in miner status page its not hashing its shows as zero...
i have tried to reset the machine but its same .Attached is the screenshot.
<snip> img </snip>
Go to Network tab then click edit on your connection then switch the protocol to DHCP and Save & Apply. You'll get a new IP address, so it will not be on 192.168.1.99 anymore, but will begin hashing straight away. yes i tried that but even then its not hashing..now the network have assigned it a value 192.168.1.100... 12 seconds into startup wait for 5 minutes. if it still shows 0 post a screen shot its same after 5 mins also..after some time its restarts..but the values is never shown greater then 0. <snip> img </snip> Hmm ... check your logs, both the system log and the kernel log. you can also try stopping then starting cgminer then check the logs. |
|
|
|
|
