vapourminer
Legendary
Offline
Activity: 4452
Merit: 3970
what is this "brake pedal" you speak of?
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 17, 2016, 11:44:51 PM Last edit: July 18, 2016, 01:57:52 AM by vapourminer |
|
I have an existing Minera setup which works well so I thought I would try the cgminer-gekko image posted in this thread.
However whenever I plugin the USB Miner I get the following:
Which is great but it's followed by:
I've also updated the firmware of the PI, updated all of the software packages and updated minera to v0.7.0
Anyone else have the same setup and had this problem?
Regards Gareth
i never got minera on the rpi b to work with my compacs.. probably user error and i didnt mess with it to be honest. i just disabled minera and compiled straight from the source for the gekko version of cgminer. upshot is I just didnt use minera, i compiled the gekko version of cgminer on the pi and ran it from a terminal.
|
|
|
|
vapourminer
Legendary
Offline
Activity: 4452
Merit: 3970
what is this "brake pedal" you speak of?
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 18, 2016, 01:58:22 AM |
|
btw the 4 compacs on the rpi have run several months non stop perfectly. they (pi/hub/compacs/switch/modem/router) are all on ups, so that helps too; crappy power here.
the 5th, compiled on ubuntu 15.10 runs fine for weeks at a stretch but that rig is not on a ups so it drops dead when power glitches otherwise im sure it would run non stop also.
|
|
|
|
drew_ii
Newbie
Offline
Activity: 33
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 12:44:05 PM |
|
vapourminer, or any other pi-heads out there, I searched the forum here and elsewhere and can't find an answer.
On my either 2B or 3b (I'm pretty sure 3B) I run two copies of cgminer concurrently - one runs 4 sticks at 425, and the other runs three sticks at about 350 or 375, whatever I can get them cranked to.
POWER for the pi comes from an unpowered (port on-off switchable) hub connected to a powered 2.0 hub, as does the on board pi port go to the powered 2.0 hub. THe 2.0 uplinks to 2xSuperbpag 3.0 running sticks in alternate slots, staggered for maximum airflow, with four fans going on. Two fans are run from the *2.0* hub, and the other two from the secondary 3.0 hub (where the three slower sticks sit).
Here's the issue:
If I run both simultaneously, I can almost always count on loss of network connectivity within 24 hours. I can restore it by unplugging and replugging the network cable, and there's some talk of ifup/ifdown commands to refresh the DHCP lease, or setting the IP static. I Also added eligius to the hosts file to see if that helped, but it didn't. I lose the ability to talk to eligius and im down until I notice it.
HOWEVER - if I just run the 4 sticks at 425 its rock solid for days. (the other three are plugged into their superbpag but the hardware refresh is 0'd out or they are zombied on my active cgminer)
Any ideas?
Thanks,
drupie
|
|
|
|
JeffZwolle
|
![](https://bitcointalk.org/Themes/custom1/images/post/lamp.gif) |
July 20, 2016, 04:46:32 PM |
|
|
Donations are always welcome :-) 1C447F2zd9KdoRCpi8mMAYNiLqqh3JDsiY
|
|
|
cavaliersrus
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 06:21:13 PM |
|
very cool and interesting idea there
|
|
|
|
Mikestang
Legendary
Offline
Activity: 1274
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 06:30:50 PM |
|
I like the little fan mount, cool idea. You could probably even get 2 of them on there and then cover the entire heat sink. Do you have a laser thermometer? Would be interesting to see what the temp difference is on the heat sink beneath the fan and on the sides.
|
|
|
|
drew_ii
Newbie
Offline
Activity: 33
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 08:12:17 PM |
|
Thoughts about soldering the power leads direct to the +5v/Grnd leads of the USB connector instead of running it off of another port through another cable?
Drupie
|
|
|
|
gt_addict
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 08:59:56 PM |
|
Someone has already soldered a barrel plug to the 5v and gnd for additional power delivery. Its further back in this thread I think, or try the gecko run thread on the main page.
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
JeffZwolle
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 09:15:03 PM |
|
I like the little fan mount, cool idea. You could probably even get 2 of them on there and then cover the entire heat sink. Do you have a laser thermometer? Would be interesting to see what the temp difference is on the heat sink beneath the fan and on the sides.
Yes, I do have one of those. temperatures: Room: 30 degr C Heatsink side: 40 degr C Fan top: 41 degr C Heatsink under fan: 61 degr C Room temperature is pretty high because of outside temperature being 34 degr C here today.
|
Donations are always welcome :-) 1C447F2zd9KdoRCpi8mMAYNiLqqh3JDsiY
|
|
|
chiguireitor
Legendary
Offline
Activity: 872
Merit: 1010
Coins, Games & Miners
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 20, 2016, 11:25:45 PM |
|
Isn't this the cutest littlest fan! I just found 4cm fans for my sticks and they looked completely out of place ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif)
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 21, 2016, 04:31:05 AM |
|
|
|
|
|
drew_ii
Newbie
Offline
Activity: 33
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 21, 2016, 06:05:45 PM |
|
Welp one just died. Wont even init. Solid green, no init pulse, wont run at 150, just sits at 0. I think I killed the chip. RIP little bugger. Waiting on MM Test Leads to ensure core voltage etc.
|
|
|
|
TouchFluffyTail
Newbie
Offline
Activity: 13
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 24, 2016, 02:48:29 AM |
|
I have 3 sticks sitting in a Rosewill hub that also powers the rPI that controls them and Arctic usb fan. I've noticed yesterday that one stick flashes slightly pink when it's hashing, it still has a solid green LED on. the other 2 flash normal white. I'm still getting a stable 32~36 Gh/s.
Is that normal, or is it indicating that the stick is about to die?
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 24, 2016, 03:19:03 AM |
|
The flashing circuit is completely independent of the hashing and controls parts. More likely it's an issue with the LED or an attached resistor.
|
|
|
|
TouchFluffyTail
Newbie
Offline
Activity: 13
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 24, 2016, 05:47:51 AM |
|
The flashing circuit is completely independent of the hashing and controls parts. More likely it's an issue with the LED or an attached resistor.
Thanks, I will just leave it alone and try not to get bothered by it.
|
|
|
|
MrBogy
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 25, 2016, 02:35:15 PM |
|
Greetings.
I've been attempting to get my Compac working for the past week. All attempts in using gekko-cgminer (including but not limited to reinstalling various drivers and a fresh install of my OS) have invariably ended in the following error:
The application was unable to start correctly (0xc000007b). Click OK to close the application.
Attempts to use bfgminer have met with a small degree of success, but I am unable to find the device.
Since I am using Windows 10, I have used zadig to install the proper driver, but I am now at a loss as to what to do next.
Any advice would be greatly appreciated, and thank you in advance.
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 25, 2016, 02:49:21 PM |
|
I'm assuming you've looked into the thread enough to know there's a DLL missing from the Windows build that needs to be copied across from a stock cgminer archive?
|
|
|
|
MrBogy
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 25, 2016, 03:06:13 PM |
|
I'm assuming you've looked into the thread enough to know there's a DLL missing from the Windows build that needs to be copied across from a stock cgminer archive?
Gadzooks! Foiled by my own poor eyesight! A quick search solved my dilemma, and all is now well. As thanks for your quick reply, I'll donate the first few days of mining to the listed sandwich address, unless there's another one you prefer.
|
|
|
|
boymoku
Newbie
Offline
Activity: 8
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 26, 2016, 11:13:35 PM |
|
Helo Everyone , I am new Can I ask something , i have GekkoScience Compac BM1384 and How i use this with Window 7 64 Bit and How can i run it ? Thank u http://www.uppic.org/image-A28E_5797EF2C.jpg
|
|
|
|
ZedZedNova
Sr. Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 475
Merit: 265
Ooh La La, C'est Zoom!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
July 27, 2016, 12:13:17 AM |
|
Helo Everyone , I am new Can I ask something , i have GekkoScience Compac BM1384 and How i use this with Window 7 64 Bit and How can i run it ? Thank u ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.uppic.org%2Fimage-A28E_5797EF2C.jpg&t=665&c=bQtcpZJ4PPzBQA) 1. Read the first post of this thread. 2. keep reading following posts that answer questions 3. try what is suggested 4. If that still hasn't worked, keep reading more of the thread posts 5. After reading first few pages of posts in this thread Go back to #1 Pretty much everything you need to know is covered in the first few pages of this thread. Cheers, - zed
|
No mining at the moment.
|
|
|
|