Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[VicePrez]

I was using a hack to take dev-fee away but going from 9.3 -> 9.5 two days ago and seeing a 8% increase on my nVidia 1060 plus the new toys to play with in 10.0 I've stopped using thank. Thanks clay.

Has anyone seen last years documentary on Bitcoin?

Edit: Does anyone know what kind of memory the XFX R9 290x has? I'm getting one of them and one "non-name" brand in the mail today and would love to put a 390 bios on them, unlocked the shaders on my rx 460 and it increased hashrate hugely; I hear you can get 54 Mh/s on the Samsung memory with the 390 bios.

I can't even begin to process the logic involved in your first statement. So I decided to create an account.. to call you a fool. Touche sir, you grabbed my attention.

[Ginzink]

Tried to mine cryptonight with rx Vega , got error:AMD HSA Code Object loading failed

Then claymore Said unable to allocate memory.
Got 32gb ram and alot of virtual.

My 1080 ti works fine (not claymore miner)

[SummersideGuy]

when i mine ETH with 5X RX470 i am getting 130 mh/s

but when i mine ETC with same 5X RX470 i am getting only 115 mh/s


why 15 mh/s  diffrence?

what drivers are u using, if you are using something other then block chain drivers then that is the answer as ETC is on a higher DAG then ETH

[Yohow]

Claymore 10 + blockchaind drivers aug11 + patch + Win 10 creators + rx580s = the most stable mix until now!

When -r 0 no more system freeze, it just restart the miner smoothly. Fans are back in control when set the temp, voltage can be controlled (I have to figure it out why I can't go lower than 0.938 v). Overall, this is the most stable version ever. Thank you man!

thanks for the info but what is the "+ patch" in your post ?

TYIA

https://www.monitortests.com/atikmdag-patcher-1.4.5.zip for bypass pixel clock limit on AMD drivers.

[cdnminer]

Hi all,

I have done quite a lot of research but haven't found a resolution to this problem - hopefully someone can help me on this.

Mining rig:
3 x MSI RX 580 8 GB cards (not Armor/Sapphire etc) - has single 8 pin power connector, single fan, no BIOS switch
Windows 10
SSD with 4 GB RAM
Installed Claymore version 10 Dual miner - Ethereum mining running well and stable but issue is that I cannot get Decred to authorize

Getting:
Socket was closed remotely (by pool)
 DCR: Job timeout, disconnect, retry in 20 sec...

Start.bat command:
EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal 0x31be6e3~~~~~~~~~~~~~~~~~98c6.miner2 -dpool dcr.suprnova.cc:3252 -dwal myloginname.miner1 -dpsw 2222 -allpools 1

Troubleshooting:
- I have changed the password for the worker to match Claymore (x, 2222, other) - unable to leave the password blank for the worker
- verified Suprnova login (though there is an "x" in the active column?)
- attempted both weblogin name as well as email address used for profile
- added port 3252 in Windows firewall for both incoming and outgoing connections
- added miner to router's DMZ
- tried with/without stratum+tcp
- attempted -dpool dcr.suprnova.cc:3252 -dwal suprnova.1 -dpsw x -allpools 1 as detailed on suprnova's website
- though I can't recall which other decred pools I used but all got the same error

Any assistance or suggestions would be greatly appreciated!!

[Yohow]

Hi all,

I have done quite a lot of research but haven't found a resolution to this problem - hopefully someone can help me on this.

Mining rig:
3 x MSI RX 580 8 GB cards (not Armor/Sapphire etc) - has single 8 pin power connector, single fan, no BIOS switch
Windows 10
SSD with 4 GB RAM
Installed Claymore version 10 Dual miner - Ethereum mining running well and stable but issue is that I cannot get Decred to authorize

Getting:
Socket was closed remotely (by pool)
 DCR: Job timeout, disconnect, retry in 20 sec...

Start.bat command:
EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal 0x31be6e3~~~~~~~~~~~~~~~~~98c6.miner2 -dpool dcr.suprnova.cc:3252 -dwal myloginname.miner1 -dpsw 2222 -allpools 1

Troubleshooting:
- I have changed the password for the worker to match Claymore (x, 2222, other) - unable to leave the password blank for the worker
- verified Suprnova login (though there is an "x" in the active column?)
- attempted both weblogin name as well as email address used for profile
- added port 3252 in Windows firewall for both incoming and outgoing connections
- added miner to router's DMZ
- tried with/without stratum+tcp
- attempted -dpool dcr.suprnova.cc:3252 -dwal suprnova.1 -dpsw x -allpools 1 as detailed on suprnova's website
- though I can't recall which other decred pools I used but all got the same error

Any assistance or suggestions would be greatly appreciated!!

Try to change "miner1" to your "worker name" and write "-dpsw x" command too.

Appreciations here (ETH) 0x57137Aecf8d11b60522d53eD2b0Baf0215FD0b61

[DrX]

Hi all,

I have done quite a lot of research but haven't found a resolution to this problem - hopefully someone can help me on this.

Mining rig:
3 x MSI RX 580 8 GB cards (not Armor/Sapphire etc) - has single 8 pin power connector, single fan, no BIOS switch
Windows 10
SSD with 4 GB RAM
Installed Claymore version 10 Dual miner - Ethereum mining running well and stable but issue is that I cannot get Decred to authorize

Getting:
Socket was closed remotely (by pool)
 DCR: Job timeout, disconnect, retry in 20 sec...

Start.bat command:
EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal 0x31be6e3~~~~~~~~~~~~~~~~~98c6.miner2 -dpool dcr.suprnova.cc:3252 -dwal myloginname.miner1 -dpsw 2222 -allpools 1

Troubleshooting:
- I have changed the password for the worker to match Claymore (x, 2222, other) - unable to leave the password blank for the worker
- verified Suprnova login (though there is an "x" in the active column?)
- attempted both weblogin name as well as email address used for profile
- added port 3252 in Windows firewall for both incoming and outgoing connections
- added miner to router's DMZ
- tried with/without stratum+tcp
- attempted -dpool dcr.suprnova.cc:3252 -dwal suprnova.1 -dpsw x -allpools 1 as detailed on suprnova's website
- though I can't recall which other decred pools I used but all got the same error

Any assistance or suggestions would be greatly appreciated!!

add -"dcoin dcr" option and add "miner1" as an worker in dcr.suprnova.cc site.

[greatauror28]

So i have this weird problem.

My rig works fine with its current setup (Claymore 9.8, aug11 blockchain drivers, WIn10 7310) and has ran for 7 days nonstop, till I had to restart it.

First, GPUs 0 to 5 would be detected, then after 30 seconds GPU5 will show zero hashrate. Eventually 10 seconds later, it would hang. Then if it didn't froze on me, I would restart Claymore.

Sometimes Claymore restarts automatically when this happens, and I see a popup message on the lower right saying "AMD Radeon has been restored to default settings..."

Most of the time, after I see that error message and Claymore has restarted, All 6 GPUs would hash properly and run fine. Half the time, I had to do 3-4 restarts for it to work again.

But I just want to narrow down which is really causing the issue. I'm using new risers, tried changing usb cable, 6-pin sata power, but still the same issue.

Interesting note:
Of all 6 cards that GPU5 only is the single card that takes -150mV and still run fine. GPU-z shows .9375mV after the -150mV has been applied.

Cards are Asus Dual OC Rx 580 8GB 1260/2050/-125 to -150mV

Anyone?

[mamoEB]

I have exact same problem with stability with new versions. After 2-3 restarts everything is OK but after random interval of time the instability is fact. 

So i have this weird problem.

My rig works fine with its current setup (Claymore 9.8, aug11 blockchain drivers, WIn10 7310) and has ran for 7 days nonstop, till I had to restart it.

First, GPUs 0 to 5 would be detected, then after 30 seconds GPU5 will show zero hashrate. Eventually 10 seconds later, it would hang. Then if it didn't froze on me, I would restart Claymore.

Sometimes Claymore restarts automatically when this happens, and I see a popup message on the lower right saying "AMD Radeon has been restored to default settings..."

Most of the time, after I see that error message and Claymore has restarted, All 6 GPUs would hash properly and run fine. Half the time, I had to do 3-4 restarts for it to work again.

But I just want to narrow down which is really causing the issue. I'm using new risers, tried changing usb cable, 6-pin sata power, but still the same issue.

Interesting note:
Of all 6 cards that GPU5 only is the single card that takes -150mV and still run fine. GPU-z shows .9375mV after the -150mV has been applied.

Cards are Asus Dual OC Rx 580 8GB 1260/2050/-125 to -150mV

Anyone?

[ascaloon]

Hi!

Could anyone share with me a good stable cc+mc+mv settings for dual ETH+DCR mining? I have 7xRX580 nitro+limited e. bios moded cards.

Thanks in advance.

[kkourmousis]

ETH+DCR RX 580 8GB Nitro+

My personal sweet spot is  -cclock 1140 -mclock 2150 -cvddc 850 -mvddc 875.
For those voltages, I have to lower mclock for some cards.
I prefer those voltages because I have high price of kWh in my country (~0.3$)

[iRrromka]

Cards are Asus Dual OC Rx 580 8GB 1260/2050/-125 to -150mV

Anyone?

Hi again! With new amd bc drivers (23 aug) and Clay 10.0 I flashed UberMix 3.1 straps to these cards (Asus Dual OC). They are working fine but 1162/1960/900mV - 28 mh per card.

Sudden OpenCL errors happens.

I think, we have to calm down and wait for new Clay release

[jaimefcb]

Hi there,
Do you guys have an idea about what is going on with my rig?
In here an image from Nanopool Hasrate Calculated vs Reported
https://imgur.com/a/Jw5Fe

I have latest Blockchain Drivers (23Aug) and Claymore v10. My rig config is 7x580 Sapphire+ 8G

As you can see on the image I have several drops along the day on Calculated hashrate (normally hard-resseting is enough, but not always...), and my system used to be stable as a rock! I have BIOS mod with optimal timings and OC memories (each one fine tunned to have 0 errors), UC GPU to 1130MHz and UV GPU to -96mV.

Are those drops related with Drivers, Mining SW, Card config or Pool?

Thanks!

[iRrromka]

Hi there,
Are those drops related with Drivers, Mining SW, Card config or Pool?
Thanks!

value for -dcri option?

[jaimefcb]

Hi there,
Are those drops related with Drivers, Mining SW, Card config or Pool?
Thanks!

value for -dcri option?

Single Mining since some weeks now. -asm & -dcri @default values.

[iRrromka]

Hi there,
Are those drops related with Drivers, Mining SW, Card config or Pool?
Thanks!

value for -dcri option?

Single Mining since some weeks now. -asm & -dcri @default values.

I've noticed, that my rx580 likes -dcri 5 in ethereum only. But it's not about your case, sorry

[jaimefcb]

I've noticed, that my rx580 likes -dcri 5 in ethereum only. But it's not about your case, sorry

Thanks for your help, I will play a little with -dcri values because, you are right, asm is enabled by default. I can also see some little improvement on ETH MH/s when I enable Dual Mining.

In any case, I think I will improve a little my hashes reported but no calculated ones... I really have no idea why that huge drop.

[shadabahmed]

when i mine ETH with 5X RX470 i am getting 130 mh/s

but when i mine ETC with same 5X RX470 i am getting only 115 mh/s


why 15 mh/s  diffrence?

what drivers are u using, if you are using something other then block chain drivers then that is the answer as ETC is on a higher DAG then ETH

i am using 16.12.12 driver

can u suggest me which is good driver for my RX 470 4gb?

[AzzAz]

@claymore, how can i reset the overclocking of your program? where ca i find it? regedit? I mean, I had to change its name to reset the settings.

There is no simple way to restore default clocks. You can reinstall drivers, or do it via WattMan, also in most cases drivers apply default clocks after GPU driver crash.

And next time use "set" not "setx" in .bat...

[arithon]

Appreciate it if someone can give some input

Need help from Ubuntu experts

Hi!  I need some help from Ubuntu experts.  I set up a test rig using the Sapphire Nitro+ RX580 on Windows 10, using Afterburner to do some mild overclocking - Stable on Claymore 9.8 with customised fan profile.  I flashed the bios with the Hynix timing straps and I am getting around 24mhs, which is not bad, but not great either.   It is stable.

However, when I tried set up an Ubuntu environment (16.04), I can get it stable at standard clock rates - however it crashes when I raised the clock rate using the flashed bios with the overclocked memory that works well in windows.   The fan seems to be kicking in very late, and I was getting 76 degrees at 25% fan. 

Here's a list of my questions that I hope the Ubuntu/Claymore experts can help with as I am a beginner in Ubuntu:

1.  I tried using the -tt and -fanmin command in Claymore.  I get the error message "Failed to set new fan speed, check if miner has root access!".   How do I set the miner to have root access?   Right now, I am starting the miner with the command in terminal "./mine.sh", where mine.sh is the claymore start file. 

2.  I am getting a list of error messages off the standard environment variables in Claymore.  As below:

"alvin@cryptominer-one:~/Desktop/Claymore98$ ./mine.sh
./mine.sh: line 1: export: `0': not a valid identifier
./mine.sh: line 2: export: `100': not a valid identifier
./mine.sh: line 3: export: `1': not a valid identifier
./mine.sh: line 4: export: `100': not a valid identifier
./mine.sh: line 5: export: `100': not a valid identifier?

Appreciate some insights into the above.

3.  -mclock 2100 doesn't seem to have any impact on the hash rate (standard is 2000).   Am I using it correctly?

4.  How do I monitor GPU status in Ubuntu?  Aticonfig doesn't seem to work.

Thanks!

1 - Check your script, seems you are not using the export properly.
2 - Check the FAQ,  it's supported in Linux.
3 - You won't get exactly what you have in Win, you have to check different sources to get some of that info.

Thanks for the input but i am getting nowhere on ubuntu.

1.  I copied the "export" commands exactly as I found them in Claymore 9.8 from the sample scripts. Not sure what I am doing wrong. 
2.  I still can't get the fanmin command to work. It needs root access - how do I do that in Ubuntu?

Cheers!