smparo
Newbie
 Offline
Activity: 27
Merit: 0
|
 |
September 01, 2017, 04:29:22 PM
Last edit: September 01, 2017, 04:42:17 PM by smparo |
|
Just updated, with RX 580 not changes on MH/s but now I can set voltage/clocks without problems (robinhood driver)! Thanks!!!  |
|
|
|
|
|
|
|
|
|
Every time a block is mined, a certain amount of BTC (called the
subsidy) is created out of thin air and given to the miner. The
subsidy halves every four years and will reach 0 in about 130 years.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
|
dragonmike
|
|
September 01, 2017, 04:35:33 PM |
|
Just updated, with RX 580 non changes on MH/s but now I can set voltage/clocks without problems (robinhood driver)! Thanks!!! you set them in Claymore, correct? |
|
|
|
|
smparo
Newbie
Offline
Activity: 27
Merit: 0
|
|
September 01, 2017, 04:38:24 PM |
|
Just updated, with RX 580 not changes on MH/s but now I can set voltage/clocks without problems (robinhood driver)! Thanks!!! you set them in Claymore, correct? Yes |
|
|
|
|
|
spyshagg
|
|
September 01, 2017, 04:50:57 PM |
|
@claymore Every version since 9.4 won't allow me to connect via stratum  9.4 works fine. Exactly the same batch file. Did something change? |
|
|
|
|
|
Call_Me_Bambi
|
|
September 01, 2017, 05:03:56 PM |
|
Version 10.0 now available on Mega.
|
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
September 01, 2017, 05:04:38 PM |
|
@claymore Every version since 9.4 won't allow me to connect via stratum 9.4 works fine. Exactly the same batch file. Did something change? try port 14444? also make sure you use -mode 1 in the bat. i use this pool it works just fine. |
|
|
|
|
ironblade
Newbie
Offline
Activity: 1
Merit: 0
|
|
September 01, 2017, 05:15:49 PM |
|
Hi,
I've installed last version today and I have this message time to time
ETH: Received error: {"jsonrpc":"2.0","id":4,"error":{"code":-32700,"message":"Worknotfound"}}
But it seems to be working
Thanks
|
|
|
|
|
|
Intristing
|
|
September 01, 2017, 05:30:01 PM |
|
Version 10.0 now available on Mega.
Can we change the voltage for AMD R9 390? |
|
|
|
|
johndoe2
Newbie
Offline
Activity: 21
Merit: 0
|
|
September 01, 2017, 05:32:42 PM
Last edit: September 01, 2017, 05:42:48 PM by johndoe2 |
|
Thanks for the update Claymore, I just updated my 7 Gpu hybrid rig to 10.0. My multimedia PC seems to be crashing so I'm using the previous version for now
|
|
|
|
|
platitude
Member
Offline
Activity: 103
Merit: 10
|
|
September 01, 2017, 05:37:44 PM
Last edit: September 01, 2017, 07:48:55 PM by platitude |
|
Win 10, Sapphire RX580 Pulse 4GB cards, Blockchain drivers(23 Aug) installed, Claymore v10.0 is crashing from time to time, after crash I need to restart BAT file, because of hashrate drop. Waiting for a fix or new version 22:38:44:695 14f4 watchdog - thread 2 (gpu1), hb time 85609
22:38:44:695 14f4 WATCHDOG: GPU 1 hangs in OpenCL call, exit
22:38:44:696 14f4 watchdog - thread 3 (gpu1), hb time 85531
22:38:44:696 14f4 WATCHDOG: GPU 1 hangs in OpenCL call, exit
22:38:44:699 14f4 OC v7, Reset control for GPU 0, close miner right now if you want to use default control from Catalyst
22:38:44:700 14f4 OC v7, Reset control for GPU 1, close miner right now if you want to use default control from Catalyst
22:38:45:806 14f4 Restarting OK, exit... |
|
|
|
|
rednoW
Legendary
Offline
Activity: 1510
Merit: 1003
|
|
September 01, 2017, 05:38:14 PM |
|
40mh eth + 290mh lbry )) vega64 liquid
|
|
|
|
|
TigTex
Jr. Member
Offline
Activity: 55
Merit: 5
|
|
September 01, 2017, 05:40:13 PM |
|
Just leaving feedback here on the version 10.0
Using 5x RX580 and the amd blockchain driver from 23rd august, it's now possible to parcially control the voltage.
I had my voltage set at 0.875v but the driver ignores and it sets 0.912 as the minimum. If I set 0.800, it still selects 0.912v.
So this means that I have an increase in power consuption. My 5 gpu rig now uses 120w more power.
So, if you have this 0.912v limit as I have, don't use a low core clock because with 0.912 you can do near 1300mhz stable (rx 580 sapphire pulse)
With that extra core speed, make sure that you increase the DCRI value so that the second coin uses the full extra MHz for maximum efficiency.
Before: ETH 144MHs DCR 4700MHs (at 1200mhz 0.875v) +/- 840w
Now: ETH 150MHs DCR 5750MHs (at 1300mhz 0.912v) +/- 960w
Because I pay 0.17€/kW, it's almost not worth the extra speed vs power consuption.
Please reply if you also can't set the voltage any lower than 0.9v
|
.::. TigTex .::.
Good luck! Have a nice hash
|
|
|
z0n0
Legendary
Offline
Activity: 1274
Merit: 1006
|
|
September 01, 2017, 05:47:21 PM |
|
Any speed improvements with GTX 1060?
|
|
|
|
|
|
Shnikes101
|
|
September 01, 2017, 05:48:07 PM |
|
40mh eth + 290mh lbry )) vega64 liquid
Beta Mining Drivers or 17.8.2? On 17.8.2 I'm at 36 mh eth + 220mh lbc. May have to switch back over and try the other drivers |
|
|
|
|
platitude
Member
Offline
Activity: 103
Merit: 10
|
|
September 01, 2017, 05:59:49 PM
Last edit: September 01, 2017, 07:48:09 PM by platitude |
|
Just leaving feedback here on the version 10.0
Using 5x RX580 and the amd blockchain driver from 23rd august, it's now possible to parcially control the voltage.
I had my voltage set at 0.875v but the driver ignores and it sets 0.912 as the minimum. If I set 0.800, it still selects 0.912v.
So this means that I have an increase in power consuption. My 5 gpu rig now uses 120w more power.
So, if you have this 0.912v limit as I have, don't use a low core clock because with 0.912 you can do near 1300mhz stable (rx 580 sapphire pulse)
With that extra core speed, make sure that you increase the DCRI value so that the second coin uses the full extra MHz for maximum efficiency.
Before: ETH 144MHs DCR 4700MHs (at 1200mhz 0.875v) +/- 840w
Now: ETH 150MHs DCR 5750MHs (at 1300mhz 0.912v) +/- 960w
Because I pay 0.17€/kW, it's almost not worth the extra speed vs power consuption.
Please reply if you also can't set the voltage any lower than 0.9v
Try to set 840 for example and tell us if it works, cause it looks like I had the same issue. I mean check wich card is showing you wrong voltage and set separatelyfor each card with comma, like: 840,870,870,870,870 --- Update: I've set 848 value only and it works for me, try to decrease the value. Also it look's like the problem with values setting is there and you need to restart the miner every time |
|
|
|
|
rednoW
Legendary
Offline
Activity: 1510
Merit: 1003
|
|
September 01, 2017, 06:02:50 PM |
|
40mh eth + 290mh lbry )) vega64 liquid
Beta Mining Drivers or 17.8.2? On 17.8.2 I'm at 36 mh eth + 220mh lbc. May have to switch back over and try the other drivers 17.8.2, clocks 1500/1080@1v, consumption is huge - 360watt also can do 1340/1020@0.95v. 38.2eth+250lbry with 280-300watt |
|
|
|
|
wOvAN
Jr. Member
Offline
Activity: 41
Merit: 3
|
|
September 01, 2017, 06:04:24 PM |
|
v10 still not working on win 7 blockchain driver
|
|
|
|
|
rednoW
Legendary
Offline
Activity: 1510
Merit: 1003
|
|
September 01, 2017, 06:14:51 PM |
|
v10 still not working on win 7 blockchain driver
use robinhood drivers under win7 |
|
|
|
|
wOvAN
Jr. Member
Offline
Activity: 41
Merit: 3
|
|
September 01, 2017, 06:23:33 PM |
|
v10 still not working on win 7 blockchain driver
use robinhood drivers under win7 yes, but they not seem to be able to do any undervolt with v10 |
|
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
|
September 01, 2017, 06:25:35 PM |
|
@claymore
9.4 works fine. Exactly the same batch file. Did something change?
I change something all the time, but it works for all, so you should look for the reason in your environment: installed software or internet connection. v10 still not working on win 7 blockchain driver
Blockchain drivers for Win7 are broken. 40mh eth + 290mh lbry )) vega64 liquid
LBC has good speed finally. Also in ETH-only mode I get >44MH at 1100MHz memory (air cooled Vega 64). The only problem with Vega is huge power consumption. And buggy ADL, but this problem is related to several cards. |
|
|
|
|
