[Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner

[aurel57]

Will it damange the S1 by only running power to the side with the ethernet port and not hooking power to the opposite side? Basically only mining from one board. I am having power issues right now where I keep blowing the fuse to the circuit box.

If your running that tight on the circuit I think I would just unplug the miner. Not worth the risk to your home/building.

Edit: Also I have penciled mod and undervolt my 9 S1's which dropped the watts by 200 each and still hash @140 which maybe an option for you.

[kevin1234a]

i wanted to point multiple S1 to the same worker so total 400Ghs (approx) will consume by one worker only.

Any suggestion or advise on how to do it?

[chadwickx16]

i wanted to point multiple S1 to the same worker so total 400Ghs (approx) will consume by one worker only.

Any suggestion or advise on how to do it?

Use the same worker name for both and set the difficulty at the pool to 256. No issue as all. I keep mine separate in case one goes down.

[alesx.onfire]

i wanted to point multiple S1 to the same worker so total 400Ghs (approx) will consume by one worker only.

Any suggestion or advise on how to do it?

Use the same worker name for both and set the difficulty at the pool to 256. No issue as all. I keep mine separate in case one goes down.

i don't know why, but with 256 diff, get more shares per "shift" (72k - 76k) ---> (84k - 92k) with 3 s1.  (190gh >256) + (190gh >128) + (200gh >256)
0.52% or less rejected.

[chadwickx16]

i wanted to point multiple S1 to the same worker so total 400Ghs (approx) will consume by one worker only.

Any suggestion or advise on how to do it?

Use the same worker name for both and set the difficulty at the pool to 256. No issue as all. I keep mine separate in case one goes down.

i don't know why, but with 256 diff, get more shares per "shift" (72k - 76k) ---> (84k - 92k) with 3 s1.  (190gh >256) + (190gh >128) + (200gh >256)
0.52% or less rejected.

If you have three different workers they should be set to 128 each. A good rule of thumb is to set difficulty to the power of two below your hashrate.

[Maldrien]

Hi guys I've read some of the pages of the thread and did a google search without finding the answer to my question.

I bought 2 Antminer S1

Both of them are plugged in a Thermaltake 750 watt PSU

After 24h hours of mining one of them is showing alot of HW errors. Like half the shares. All ASICs chips are OK and both S1 are plugged in the same switch pointing to the same pool.

I did a reboot on the S1 with all the errors and after only 17 minutes it's already showing the same trend.

Could it be my PSU?

Here's a screenshot after the reboot

http://www.flickr.com/photos/56699195@N00/14856322640

Thanks for the help!

[chadwickx16]

Hi guys I've read some of the pages of the thread and did a google search without finding the answer to my question.

I bought 2 Antminer S1

Both of them are plugged in a Thermaltake 750 watt PSU

After 24h hours of mining one of them is showing alot of HW errors. Like half the shares. All ASICs chips are OK and both S1 are plugged in the same switch pointing to the same pool.

I did a reboot on the S1 with all the errors and after only 17 minutes it's already showing the same trend.

Could it be my PSU?

Here's a screenshot after the reboot

http://www.flickr.com/photos/56699195@N00/14856322640

Thanks for the help!

Your hardware errors are fine at a 0.35% rate. To calculate use HW/(HW+DiffA+DiffR)= HW%.

[Maldrien]

Hi guys I've read some of the pages of the thread and did a google search without finding the answer to my question.

I bought 2 Antminer S1

Both of them are plugged in a Thermaltake 750 watt PSU

After 24h hours of mining one of them is showing alot of HW errors. Like half the shares. All ASICs chips are OK and both S1 are plugged in the same switch pointing to the same pool.

I did a reboot on the S1 with all the errors and after only 17 minutes it's already showing the same trend.

Could it be my PSU?

Here's a screenshot after the reboot

http://www.flickr.com/photos/56699195@N00/14856322640

Thanks for the help!

Your hardware errors are fine at a 0.35% rate. To calculate use HW/(HW+DiffA+DiffR)= HW%.

Thanks!

[chadwickx16]

Hi guys I've read some of the pages of the thread and did a google search without finding the answer to my question.

I bought 2 Antminer S1

Both of them are plugged in a Thermaltake 750 watt PSU

After 24h hours of mining one of them is showing alot of HW errors. Like half the shares. All ASICs chips are OK and both S1 are plugged in the same switch pointing to the same pool.

I did a reboot on the S1 with all the errors and after only 17 minutes it's already showing the same trend.

Could it be my PSU?

Here's a screenshot after the reboot

http://www.flickr.com/photos/56699195@N00/14856322640

Thanks for the help!

Your hardware errors are fine at a 0.35% rate. To calculate use HW/(HW+DiffA+DiffR)= HW%.

Thanks!

No problem, you should see my HW vs Accepted after a month, HW>Accepted. But getting 200GH pool side still.

[mblados]

I have two Antminers S1 working good for the Last few Weeks their are both connected to a CX750M PSU not OCed.
In the last few days, the Miners stop working sometimes. The S1s are well connected to my network. I can log in but no Mining activity.
The Miner Status Tab is Blank. Everything was working before. Does anyone experiencing the same Problem? Or is my S1s going Bad?
Please give me some Advice. Thanks! 

[chadwickx16]

I have two Antminers S1 working good for the Last few Weeks their are both connected to a CX750M PSU not OCed.
In the last few days, the Miners stop working sometimes. The S1s are well connected to my network. I can log in but no Mining activity.
The Miner Status Tab is Blank. Everything was working before. Does anyone experiencing the same Problem? Or is my S1s going Bad?
Please give me some Advice. Thanks! 

Check your system log to see if you can find out what is happening. I've had the same issue, just needs a restart.

[mblados]

I have two Antminers S1 working good for the Last few Weeks their are both connected to a CX750M PSU not OCed.
In the last few days, the Miners stop working sometimes. The S1s are well connected to my network. I can log in but no Mining activity.
The Miner Status Tab is Blank. Everything was working before. Does anyone experiencing the same Problem? Or is my S1s going Bad?
Please give me some Advice. Thanks! 

Check your system log to see if you can find out what is happening. I've had the same issue, just needs a restart.

By "Restart", you mean a Reboot? because I have done that multiple time but still the same thing. the whole thing just started yesterday.
I left it cool down for a couple of hours and restarted both of them and everything was working fine. Few hours later, both S1 were bipping.
What was your Solution to fix your problem?

[chadwickx16]

I have two Antminers S1 working good for the Last few Weeks their are both connected to a CX750M PSU not OCed.
In the last few days, the Miners stop working sometimes. The S1s are well connected to my network. I can log in but no Mining activity.
The Miner Status Tab is Blank. Everything was working before. Does anyone experiencing the same Problem? Or is my S1s going Bad?
Please give me some Advice. Thanks! 

Check your system log to see if you can find out what is happening. I've had the same issue, just needs a restart.

By "Restart", you mean a Reboot? because I have done that multiple time but still the same thing. the whole thing just started yesterday.
I left it cool down for a couple of hours and restarted both of them and everything was working fine. Few hours later, both S1 were bipping.
What was your Solution to fix your problem?

Mine are on Internet facing IP's and I was getting DDOS'd from china. So i put the ip's on the ban list within the ant's iptables. Are they set to static ips? If it's beeping it means no internet access, so you DHCP lease may have run out.  But other than that, I'm out of solutions without more info.

[activescott]

I'm getting a 502 "Bad Gateway" message when trying to connect to one of my S1's. It's been going on for a month or so and it mines fine (thus I could ignore it this long), and I can access it via SSH, but not the web interface. Any ideas?

[aurel57]

I'm getting a 502 "Bad Gateway" message when trying to connect to one of my S1's. It's been going on for a month or so and it mines fine (thus I could ignore it this long), and I can access it via SSH, but not the web interface. Any ideas?

I had same thing on a S3 was afraid to reboot but was told to do so by Bitmain tech and it worked.

[kabopar]

Hello i accidentally remove my cgminer on my ant miner s1 under system and software.
i need help on the ff:
1) how can i install the cgminer to and what version should i install
2) where can i find the default script?


Thanks

One option is to re-flash your S1 with the latest firmware from the Bitmain support page.  Another option is to install cgminer 4.6.0 as described elsewhere in this forum.  The process for that is
login to your S1 with Putty, then enter the following:

Code:

cd /usr/bin
wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
chmod 755 cgminer
reboot

Cheers

[kabopar]

Hello i accidentally remove my cgminer on my ant miner s1 under system and software.
i need help on the ff:
1) how can i install the cgminer to and what version should i install
2) where can i find the default script?


Thanks

One option is to re-flash your S1 with the latest firmware from the Bitmain support page.  Another option is to install cgminer 4.6.0 as described elsewhere in this forum.  The process for that is
login to your S1 with Putty, then enter the following:

Code:

cd /usr/bin
wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
chmod 755 cgminer
reboot

Cheers

Thanks for the reply
may i ask what is Putty? telnet client? http://www.putty.org/  i did my research but im new to this putty thing.  is it ok to ask step by step instruction on how to do it? sorry kinda noob on this...  just in case i made a mistake is there a downloadable default file? or could i get it from another s1 unit? Thanks in advance
https://www.google.com.ph/search?q=putty&rlz=1C1GIGM_enPH568PH568&es_sm=93&biw=1600&bih=785&source=lnms&tbm=isch&sa=X&ei=LxQpVIvQGNXp8AWBvIKQBw&ved=0CAYQ_AUoAQ#facrc=_&imgdii=_&imgrc=rcP1d7UU6pYGNM%253A%3BqibTilhem5e7ZM%3Bhttp%253A%252F%252Fkb.mediatemple.net%252F_files%252Fshared%252FPutty_settings.png%3Bhttp%253A%252F%252Fkb.mediatemple.net%252Fquestions%252F1595%252FUsing%252BSSH%252Bin%252BPuTTY%252B(Windows)%3B449%3B434

what should i put in port etc?

Cheers

Yes, Putty is an SSH client, you can use the default settings, enter the ip address of your miner (need to accept the initial security certificate on first use).
re-flashing the Bitmain firmware would be simpler though.

Cheers

[sushi]

Port Number should be #22

Hello i accidentally remove my cgminer on my ant miner s1 under system and software.
i need help on the ff:
1) how can i install the cgminer to and what version should i install
2) where can i find the default script?


Thanks

One option is to re-flash your S1 with the latest firmware from the Bitmain support page.  Another option is to install cgminer 4.6.0 as described elsewhere in this forum.  The process for that is
login to your S1 with Putty, then enter the following:

Code:

cd /usr/bin
wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
chmod 755 cgminer
reboot

Cheers

Thanks for the reply
may i ask what is Putty? telnet client? http://www.putty.org/  i did my research but im new to this putty thing.  is it ok to ask step by step instruction on how to do it? sorry kinda noob on this...  just in case i made a mistake is there a downloadable default file? or could i get it from another s1 unit? Thanks in advance
https://www.google.com.ph/search?q=putty&rlz=1C1GIGM_enPH568PH568&es_sm=93&biw=1600&bih=785&source=lnms&tbm=isch&sa=X&ei=LxQpVIvQGNXp8AWBvIKQBw&ved=0CAYQ_AUoAQ#facrc=_&imgdii=_&imgrc=rcP1d7UU6pYGNM%253A%3BqibTilhem5e7ZM%3Bhttp%253A%252F%252Fkb.mediatemple.net%252F_files%252Fshared%252FPutty_settings.png%3Bhttp%253A%252F%252Fkb.mediatemple.net%252Fquestions%252F1595%252FUsing%252BSSH%252Bin%252BPuTTY%252B(Windows)%3B449%3B434

what should i put in port etc?

Cheers

Yes, Putty is an SSH client, you can use the default settings, enter the ip address of your miner (need to accept the initial security certificate on first use).
re-flashing the Bitmain firmware would be simpler though.

Cheers

what port should i put? i know the ip but the port where can i find it?

[DebtcoinTeam]

bitcoin-cloud.me is sell mining by the TH now

We used to have a bit of a bad record and we miss treated some customers , but we are back to stay

We are now china's largest mining farm

great prices and high quality hardware

if you ordered from us in the past and never got your order just contact us

sales@bitcoin-cloud.me

[jc01480]

Search Bitcoin-cloud.me in these forums for the real scoop.