KanoPool since 2014 🐈 - PPLNS and Solo 0.5% fee - Worldwide - 2437 blocks

[clgrissom3]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too  

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

[philipma1957]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too  

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

that sucks.   as always  try a lower freq.

[firetreeactual]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too  

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

That's not good...best to you on that.

Unrelated, but I'm sorta kinda pulling what hair I have left out...I need a new system drive (prefer Samsung EVO850 120GB SSD) as mine is going south, and can't seem to find a vendor that directly accepts BTC. If you have any ideas, please PM me.  

[sorry2xs]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too 

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

That's not good...best to you on that.

Unrelated, but I'm sorta kinda pulling what hair I have left out...I need a new system drive (prefer Samsung EVO850 120GB SSD) as mine is going south, and can't seem to find a vendor that directly accepts BTC. If you have any ideas, please PM me. 

tigerdirect.com

[aarons6]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too  

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

That's not good...best to you on that.

Unrelated, but I'm sorta kinda pulling what hair I have left out...I need a new system drive (prefer Samsung EVO850 120GB SSD) as mine is going south, and can't seem to find a vendor that directly accepts BTC. If you have any ideas, please PM me.  

tigerdirect.com

i heard they are going out of business.. try newegg.com or purse.io to buy from amazon..

i have used both and they are very reliable.

overstock also takes bitcoin but they can be more expensive.

[clgrissom3]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too 

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

that sucks.   as always  try a lower freq.

Thanks Phil, I lowered the frequency to 550 and that board came back to life...whew!  It doesn't seem to like running at 600.  I'm going to let it stabilize overnight before I do anything else to it.  In the morning I'll try different frequencies to see how close I can get back to 600.  It's holding right at 12.66THs on the Kano pool at the moment but it's only been running about 30 minutes so far. 

EDIT:  It is now up to 12.97THs on the Kano pool...if it stays like that overnight then maybe a frequency of 550 will be alright!    The specs for an S9 Batch 3 is 12.93TH/s ±5%    That ±5% hashing range is 12.18THs and 13.58THs so even at a lower frequency it's right in the mix there.  The HW error rate is 0.0008% so that is looking great!

[cucumi]

Well after 3 days using kano.is, what can i say is its the best pool right now. Im earning almost double compared with antpool, kano rock 

[clgrissom3]

Block by btcer!  Dang, that was just 2 minutes before the end of the day!    Welcome to the Acclaim Board with your 1st Kano Block!  

You just gotta love this pool!  

[philipma1957]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too 

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

that sucks.   as always  try a lower freq.

Thanks Phil, I lowered the frequency to 550 and that board came back to life...whew!  It doesn't seem to like running at 600.  I'm going to let it stabilize overnight before I do anything else to it.  In the morning I'll try different frequencies to see how close I can get back to 600.  It's holding right at 12.66THs on the Kano pool at the moment but it's only been running about 30 minutes so far. 

EDIT:  It is now up to 12.97THs on the Kano pool...if it stays like that overnight then maybe a frequency of 550 will be alright!    The specs for an S9 Batch 3 is 12.93TH/s ±5%    That ±5% hashing range is 12.18THs and 13.58THs so even at a lower frequency it's right in the mix there.  The HW error rate is 0.0008% so that is looking great!

fast guess is the psu runs out of gas at the 600 setting.  do you know what the psu is?


back to the blocks  we are so close to going to:

" a lighter shade of pale"  when it comes to the blocks  So  we need four more  block to come very: fast and furious.

IF we pop 4 blocks in under 90 minutes we will get to that perfectly pale green we all love to see.

[ATCkit]

my batch 2 s-9's are shipped.  so the solar array will go from 25th to 50 th   .  I am hoping the new fans ordered will help to keep the gear a bit cooler.

Mine too 

Can't wait to plug them to kano.is

My S9 Batch 3 is up and running on kano.is...the speed and HW errors of each board were looking good and holding right at 12.87 THs (13THs on the pool) for about 45 minutes.  The temps on each board were about 57, 87 and there were only about 3 errors on each board.  Then the 3rd board dropped to zero and eventually dropped out of the picture.  Now I have about 8.3THs total running with the first 2 boards.  Soft reboots have not revived that dead board yet.  I may have one of those with a faulty board and I have Toomim looking into it for me...

that sucks.   as always  try a lower freq.

Thanks Phil, I lowered the frequency to 550 and that board came back to life...whew!  It doesn't seem to like running at 600.  I'm going to let it stabilize overnight before I do anything else to it.  In the morning I'll try different frequencies to see how close I can get back to 600.  It's holding right at 12.66THs on the Kano pool at the moment but it's only been running about 30 minutes so far. 

EDIT:  It is now up to 12.97THs on the Kano pool...if it stays like that overnight then maybe a frequency of 550 will be alright!    The specs for an S9 Batch 3 is 12.93TH/s ±5%    That ±5% hashing range is 12.18THs and 13.58THs so even at a lower frequency it's right in the mix there.  The HW error rate is 0.0008% so that is looking great!

Phew! Glad to hear that. I had so much trouble with my Batch 1 S7 that I was worried you got a lemon S9. As I want to buy an S9 sometime later, i had the sinking stomach feeling when i saw your trouble. Hope it stays stable for you.

[citronick]

wow - guys - waking up to a 6 block day is perfect.... who needs the big iron right?

I will be MIA for few days because I am in last phase of my man cave move and also finalizing the S9 testing, costing etc - some serious hash coming to Kano soon.... stay tuned!

[clgrissom3]

fast guess is the psu runs out of gas at the 600 setting.  do you know what the psu is?


back to the blocks  we are so close to going to:

" a lighter shade of pale"  when it comes to the blocks  So  we need four more  block to come very: fast and furious.

IF we pop 4 blocks in under 90 minutes we will get to that perfectly pale green we all love to see.

Actually I don't really know...It's a 220V 80+ Platinum with 93.5% efficiency rating that Jonathan Toomim provides but I have never heard what brand it is.  It could be worth checking into...

[philipma1957]

fast guess is the psu runs out of gas at the 600 setting.  do you know what the psu is?


back to the blocks  we are so close to going to:

" a lighter shade of pale"  when it comes to the blocks  So  we need four more  block to come very: fast and furious.

IF we pop 4 blocks in under 90 minutes we will get to that perfectly pale green we all love to see.

Actually I don't really know...It's a 220V 80+ Platinum with 93.5% efficiency rating that Jonathan Toomim provides but I have never heard what brand it is.  It could be worth checking into...

that could be a bitmaintech  1600watt 220volt psu and i think it is a bit short based on what people have been writing.

not a lot just a bit.

I have been  fucking around with mining for 5 years spring of 2011 and I have found a ton of psu's  will do only 85%-90% of their rated numbers.  so maybe the bitmaintech psu's have just enough for the s-7 and are just short for the s-9

[sorry2xs]

fast guess is the psu runs out of gas at the 600 setting.  do you know what the psu is?


back to the blocks  we are so close to going to:

" a lighter shade of pale"  when it comes to the blocks  So  we need four more  block to come very: fast and furious.

IF we pop 4 blocks in under 90 minutes we will get to that perfectly pale green we all love to see.

Actually I don't really know...It's a 220V 80+ Platinum with 93.5% efficiency rating that Jonathan Toomim provides but I have never heard what brand it is.  It could be worth checking into...

IMO no psu will achieve any kind of efficiency rating advertised by the manufacturer if it is not connected to the device that it was intended to be used for i.e. a pc or a server with an bios and os that supports energy management also in conclusion it takes power to make power watts

[sorry2xs]

fast guess is the psu runs out of gas at the 600 setting.  do you know what the psu is?


back to the blocks  we are so close to going to:

" a lighter shade of pale"  when it comes to the blocks  So  we need four more  block to come very: fast and furious.

IF we pop 4 blocks in under 90 minutes we will get to that perfectly pale green we all love to see.

Actually I don't really know...It's a 220V 80+ Platinum with 93.5% efficiency rating that Jonathan Toomim provides but I have never heard what brand it is.  It could be worth checking into...

that could be a bitmaintech  1600watt 220volt psu and i think it is a bit short based on what people have been writing.

not a lot just a bit.

I have been  fucking around with mining for 5 years spring of 2011 and I have found a ton of psu's  will do only 85%-90% of their rated numbers.  so maybe the bitmaintech psu's have just enough for the s-7 and are just short for the s-9

I would like to the bitmain psu connected to an oscilloscope just to check how much sine product is present

[Newko]

@clgrissom3:   Glad you got that 3rd blade working in your S9, Carl. I was worried for a bit. Good call by Phil.
Ok, time for sleep here in Eastern time zone so let's start a Tues block party fellow miners on the other side of the globe and hope I Wake up to some blocks  Happy mining!

[kano]

With the old DE node, about 2/3 of miners have moved to the new one already.
I'll stop the old DE node at 10:00 UTC (about 1.5hrs from now), and that will just push the rest over.

Basically: I just stop the connections and each miner will immediately reconnect and be on the new DE node.

[kano]

SG node disconnected everyone on the SG node for a couple of minutes there at 09:40 UTC
All resolved shortly after that and everyone is back connected now also.

[kano]

With the old DE node, about 2/3 of miners have moved to the new one already.
I'll stop the old DE node at 10:00 UTC (about 1.5hrs from now), and that will just push the rest over.

Basically: I just stop the connections and each miner will immediately reconnect and be on the new DE node.

This was done at 10:01 UTC
About 10% of workers haven't reconnected yet, so I'm guessing they may be poxy rentals that don't reconnect properly.
Hash rate on the new DE node is up to 90% of the old+new total also.

[firetreeactual]

Thanks for the input...got the drive thing covered...my mining buddy here found a new SSD he forgot he had that I can use. I can get stuff from anywhere anyone else can...the FedEx guy has his own coffee cup on the shelf here... just still having some issues with finding vendors that directly take BTC. Places like Newegg can only accept it if the actual supplier takes it; they're like Amazon in that respect. They are not the root supplier of most of what they sell these days.

I've got half a dozen used HDDs around here, but don't want to replace the drive with another used one. Hopefully this drive will keep on trucking for another 24, and then I get to do the onerous cloning thing, etc. Just glad I don't have to shut down my S3s and network whilst switching.

Mine on.