Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[twicx]

Getting closer with my overclocking problems.

I can now run it stable using V10, not V10.1. Problem is, I still can't set clock values in config without a crash, and, if i set them with OverdriveN, they only stay for a minute or two before resetting back to the stock voltages. The clocks, however, stay the same.

[twicx]

Ok, so I've nearly got there.

Claymore 10 is working better for me than 10.1. What I have now is a situation where voltages, clocks etc stay perfectly stable provided I use GPUz to monitor (hwinfo seems to reset voltages oddly).

So with 1150/2000 and 810 as my settings, I'm getting 29.7mhs and hovering around 100-110w per card. Great!

But there's a catch. I can only set these clocks in overdriveN tool, which is ok, but now I have to figure out how to set it that the profile is applied on startup

[muzuca]

Finally happy with latest 17.10.3 drivers (rigs are quite stable) with one exception - I use Claymore's settings for voltages and frequencies (not AfterBurner or something similar) and have to run it twice. This is because of low hashrate after first start for some cards - cards start with 23-25MH, but after stopping the miner and running it again they sdstart at normal rate. It is a clue for me.

I’m doing this as well... but in my case 3 times restarting Claymore to get the configs.

[muzuca]

Another vote up for 17.10.3 driver.
I did windows 10 reinstall with new driver, compute option on.
Clocks up and I am getting stable +2MH per card dual mining with 850mv
Stable overnight, which never happened before with blockchain drivers. It feels like a miracle after spending many hrs trying to stabilize RX 580 Nitro+ with blockchain drivers.

Are you using Win 10 FCU?

[smartieee]

Finally happy with latest 17.10.3 drivers (rigs are quite stable) with one exception - I use Claymore's settings for voltages and frequencies (not AfterBurner or something similar) and have to run it twice. This is because of low hashrate after first start for some cards - cards start with 23-25MH, but after stopping the miner and running it again they sdstart at normal rate. It is a clue for me.

I am on windows 10 FCU on using AMD 17.10.2 drivers on a H110 board with 6x 470s and 4x 570s.  When I load Claymore 10.1 it doesn't accept my overclocks (I overclock from the config file not Afterburner) then it does accept it the second time I start it, if i ret restarting it a 3rd time it freezes my rig.  Not sure if this is a Claymore of driver issue :/

[chinh.daongoc]

Got incorrect temperature 511, ignore

I can not find out which card caused this error. Can you add di number to that kind of log Claymore?

Thanks

[Experimenter]

I found a small bug in last Claymore's Manager 3.5: some time later after app is minimised to tray, website shows some or all rigs in red colour like there's some fault, but all numbers are OK.

Ah! This explains why my rig is RED in web interface, while all numbers look Ok.
It's not a major issue, but still would be nice if it's sorted out.

Also, I have a suggestion for the new Detailed mode: it would be much more convenient if the summary and only the "problematic" card would be shown in red, while other cards in that rig (that are within the thresholds) stay black.

Thanks!

[tfe2012]

I try run miner on ubuntu 16_04. But get error. I have install AMD APP SDK to /opt/AMDAPPSDK-3.0

./ethdcrminer64
./ethdcrminer64: error while loading shared libraries: libOpenCL.so.1: cannot open shared object file: No such file or directory

[cas33]

I can confirm the new Afterburner 4.4.0 final is NOT working with the 17.10.3 drivers. All overclocking parameters are grayed out. Went back to the blockchain drivers.

https://www.guru3d.com/files-details/msi-afterburner-beta-download.html

Thanks for the info,you are saving me time to try this messy staffs

[kriskarthik]

Suddenly one of the GPU isn’t detected by claymore. Getting below error

Code:

22:19:25:922	1f7c	NVML version: 9.388.00
22:19:25:962	1f7c	NVML API: failed to get device handle 5, error 15.
22:19:25:986	1f7c	NVML API: failed to get device handle 5, error 15.
22:19:25:996	1f7c	NVML API: failed to get device handle 5, error 15.
22:19:26:005	1f7c	NVML API: failed to get device handle 5, error 15.
22:19:26:015	1f7c	NVML API: failed to get device handle 5, error 15.
22:19:26:026	1f7c	NVML API: failed to get device handle 5, error 15.
22:19:26:035	1f7c	NVML API: failed to get device handle 5, error 15.

How can I fix this and get the GPU up n running ?

[SnigglysMine]

Need help with direct mining of Nicehash pool(s) using Claymore Dual independently.


I downloaded Claymore Dual and wrote a .bat file that would connect my miner to the Nicehash Eth pool and the Nicehash Lbry pool.  To be perfectly clear, I am NOT USING Nicehash Legacy miner nor am I using Nicehash 2.x miner.  I am using Claymore's miner as a stand alone and pointing my rig at the Nicehash pools. 

Here is my command line:

Code:

EthDcrMiner64.exe -epool stratum+tcp://daggerhashimoto.usa.nicehash.com:3353 -ewal my btc wallet address -epsw x -esm 3 -allpools 1 -estale 0 -dpool stratum+tcp://lbry.usa.nicehash.com:3356 -dwal my btc wallet address

Please note my btc wallet address is a Nicehash btc wallet.

Problem:  When I run this and the command window pops up, it shows the second pool as being a decred pool, and, the hashrate indicates a decred hashrate, not an Lbry hashrate. What gives?  I didn't run it long enough to see if shares were actually generated because I'm not interested in decred, and I'm pretty sure it's NOT mining Lbry, based on what I see.  This happens on both of my rigs.

Any help would be appreciated!
Thanks

[ripcurrent]

Hello,

I have a quick question for a AMD Claymore 10.1 user. 

I just recently setup a rig with some rx480's installed the drivers and started to mine.

I am also running MSI Afterburner to do some overclocking, I am using the latest Beta, but when I run it all the settings are greyed out and I am not able to adjust anything.

Also my hash rates are pretty low mining ETH only 19 or so ...any sugestions would be great.

thanks

[karim_hassan777]

hi every boody
now i get a new motherboard biostar b250btc and installed 5 rx 580 + 1 rx 570 but the problem when i install win 10 fcu + 17.10.3 then msi afterbuner any edition there is no option is enabled in afterburner i tried last editin 4.4 but same results
i tried many options but in vain and in order to use afterburner i used amd blockchain driver and the core voltage control is not enabled even when you enable it from the settings and the gpus is over heated
please advise me

[Vann]

I can confirm the latest Afterburner v4.4.0 final is working with the blockchain drivers. The latest Afterburner does NOT work with the Crimson Relive 17.10.3 drivers in compute mode. Try removing the drivers in safe mode using DDU and then reinstall the drivers.

[ascaloon]

Hi,

Any information about shares decrease on ethermine.org pool after byzantium hard fork? My shares goes down dramaticaly.

[muzuca]

Hi,

Any information about shares decrease on ethermine.org pool after byzantium hard fork? My shares goes down dramaticaly.

I noticed that too... in my case the reported hashrate is ok, but the effective hashrate drops, more than 15%.

I’m trying another pool... dwarfpool

[ascaloon]

Hi,

Any information about shares decrease on ethermine.org pool after byzantium hard fork? My shares goes down dramaticaly.

I noticed that too... in my case the reported hashrate is ok, but the effective hashrate drops, more than 15%.

I’m trying another pool... dwarfpool

Please let us know later is there any change for the better on dwarfpool.

[karim_hassan777]

some users say it works good and stable moreover the core voltage is not enabled with betachain driver

[Vann]

Afterburner v4.4.0 final works fine with the blockchain drivers.

https://www.guru3d.com/files-details/msi-afterburner-beta-download.html

https://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-Blockchain-Compute-Release-Notes.aspx

[FFI2013]

Need help with direct mining of Nicehash pool(s) using Claymore Dual independently.


I downloaded Claymore Dual and wrote a .bat file that would connect my miner to the Nicehash Eth pool and the Nicehash Lbry pool.  To be perfectly clear, I am NOT USING Nicehash Legacy miner nor am I using Nicehash 2.x miner.  I am using Claymore's miner as a stand alone and pointing my rig at the Nicehash pools. 

Here is my command line:

Code:

EthDcrMiner64.exe -epool stratum+tcp://daggerhashimoto.usa.nicehash.com:3353 -ewal my btc wallet address -epsw x -esm 3 -allpools 1 -estale 0 -dpool stratum+tcp://lbry.usa.nicehash.com:3356 -dwal my btc wallet address

Please note my btc wallet address is a Nicehash btc wallet.

Problem:  When I run this and the command window pops up, it shows the second pool as being a decred pool, and, the hashrate indicates a decred hashrate, not an Lbry hashrate. What gives?  I didn't run it long enough to see if shares were actually generated because I'm not interested in decred, and I'm pretty sure it's NOT mining Lbry, based on what I see.  This happens on both of my rigs.

Any help would be appreciated!
Thanks

your missing -dcoin lbc without the -dcoin command the miner will default to dcr as a second coin