Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[spacezx]

Im a beginner Miner.....whats a good GPU to start out with?

gtx 1070 or AMD 580

for the same budget buy 2 gtx 1060 3GB and earn 50% more ...

[Victorio]

RAVE 500w aps-rv500-p01 . Input 200-240vac 4a 47-53HZ

Your PSU is a consumer grade AeroCool with 80 Plus efficiency and narrow input voltage range. Never liked AeroCool.
Provide us details about your GPU type, count and connection scheme - type of risers, power cables configuration, PCI-E cables connection to GPUs.
A simple power outage, when voltage drops from ~230V to 0V in fractions of second should not fry your PSU, while an overvoltage/undervoltage might burn some details and the PSU starts failing under load.
First check all ports for molten contacts. Then visually inspect your risers. If everything looks normally, put back the parts, take a voltmeter and check +12V in idle and under load with 15 min intervals.

[illanz]

Currently running 10.1 on ETHOS

I found that every minute or so my list of GPUs show off.Like when claymore is launching...

GPU #0: Ellesmere, 8139 MB available, 36 compute units
GPU #1: Ellesmere, 8139 MB available, 36 compute units
GPU #2: Ellesmere, 8139 MB available, 36 compute units
GPU #3: Ellesmere, 8139 MB available, 36 compute units
GPU #4: Ellesmere, 8139 MB available, 36 compute units
GPU #5: Ellesmere, 8139 MB available, 36 compute units
GPU #6: Ellesmere, 8139 MB available, 36 compute units
GPU #7: Ellesmere, 8139 MB available, 36 compute units
GPU #8: Ellesmere, 8139 MB available, 36 compute units
GPU #9: Ellesmere, 8139 MB available, 36 compute units
GPU #10: Ellesmere, 8139 MB available, 36 compute units
GPU #11: Ellesmere, 8139 MB available, 36 compute units

Is this normal

[Maniac9331]

is there a way to set a delay in claymore miner cfg? if no ,any way to delay a startup program in win 10? also any way to startup msi afterburner and load one saved profile auto?
thanks if anyone know please let me know

[XxsmasxX]

is there a way to set a delay in claymore miner cfg? if no ,any way to delay a startup program in win 10? also any way to startup msi afterburner and load one saved profile auto?
thanks if anyone know please let me know

Use ping 8.8.8.8 -n time
EthDcrminer64.exe -epool (...)

[vapourminer]

is there a way to set a delay in claymore miner cfg? if no ,any way to delay a startup program in win 10? also any way to startup msi afterburner and load one saved profile auto?
thanks if anyone know please let me know

Use ping 8.8.8.8 -n time
EthDcrminer64.exe -epool (...)

or

timeout /t 60

replace 60 with whatever (in seconds) , put in .bat file as 1st line.

for afterburner, click "apply overclocking at system startup" and just have the profile(s) you want active for each card selected at that point. it will use those profiles.

[BoostOrDie]

Can anybody help me out with  Claymore setup, with restart option?
Some times i chech my rig and it is on standby. Miner is closed. In logs it is trying to reach pool but after 2-3 tryes it just closes because cannot reach pool.

So these Are my parameters in v10.1
i use config file insted of start.bat for settings.

So this is config file:

-epool eu1.ethermine.org:4444
-ewal 0x15bc7702a8ed2710544e5e6c2e85cf2edd335938
-epsw x
-ethi 16
-mode 1
-tstop 70
-wd 1
-r >60
-mport 0

this is epool file:

 POOL: eu1.ethermine.org:14444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 0, ALLPOOLS: 0
 POOL: us1.ethermine.org:4444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 1, ALLPOOLS: 0
 POOL: us1.ethermine.org:14444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 1, ALLPOOLS: 0
 POOL: us2.ethermine.org:4444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 1, ALLPOOLS: 0
 POOL: us2.ethermine.org:14444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 1, ALLPOOLS: 0
 POOL: asia1.ethermine.org:4444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 1, ALLPOOLS: 0
 POOL: asia1.ethermine.org:14444, WALLET: 0x5704af0e1da22632410254948fd0c794037f3ccb, PSW: x, ESM: 1, ALLPOOLS: 0


I need miner to:
1) Restart incase any problems.
2) switch to epools file for alternative pool adress.

Looks like im missing something. I cant understand how to set it up. I read Readme dozens of times still cant make it work.

[BSAlex]

Try to add loop in start.bat
Something like this
____________________
:loop

EthDcrminer64

goto loop
____________________

I'll move all pool info from config.txt to epool.txt
Don't know if the last is necessary but it is make sence to keep it one place.

[jarkle]

Can we get power consumption per card added to the api??

[SummersideGuy]

hey it finally crashed after about 12 hours... weird though as machine has been solid for so long... sorry I don't know how to paste the log in different format

The log file ends unexpectedly, with no error. I suppose that must be some hardware fault. What are your clocks and voltages? You said that the rig was working flawlessly weeks long. Was it dual mining all the time?

Yup! nothing has changed which is why I'm a little surprised. I tried running it back on v10 where it was working for longer but that also crashed. went to the rig last night as well but it was working without problems so I didn’t bother restarting and running it

I have pretty much the exact same issue. I have a rig with mixed GPU's has been chugging away for the last 2 months fine then beginning of the past week crashed, for me though however when I looked at it the Nvidia cards were not being detected and Afterburner could no longer edit the amd cards settings. I reinstalled both amd and nvidia drivers but same results after about 10 minutes. I even removed the Nvidia cards and still no luck. I am gonna take some time this weekend and do a fresh install of windows and cross my fingers. Currently down 4 of 10 cards cause of this

[MikeGR7]

Im a beginner Miner.....whats a good GPU to start out with?

gtx 1070 or AMD 580

for the same budget buy 2 gtx 1060 3GB and earn 50% more ...

Yeah right... and gift them for 50 euros each in the second hand market after some months that 3GB won't be enough for dag files....

BONUS with 1060 3GB option: Crappy Hynix memory chips averaging 18MH/s....

[igotfits]

Wondering if anyone can shed some light on my issue, im switching over to ETC and ive always used claymore.

my nvidia 1060 rigg pushes out the same hash rate 24.5 per card, my amds all went from 29.5 to 19.5. any idea what it can be?

[MikeGR7]

Wondering if anyone can shed some light on my issue, im switching over to ETC and ive always used claymore.

my nvidia 1060 rigg pushes out the same hash rate 24.5 per card, my amds all went from 29.5 to 19.5. any idea what it can be?

Use amd blockchain drivers from 23 August or if you Use latest version of Windows 10 give a try to latest relive drivers with compute mode enabled.

[igotfits]

Wondering if anyone can shed some light on my issue, im switching over to ETC and ive always used claymore.

my nvidia 1060 rigg pushes out the same hash rate 24.5 per card, my amds all went from 29.5 to 19.5. any idea what it can be?

Use amd blockchain drivers from 23 August or if you Use latest version of Windows 10 give a try to latest relive drivers with compute mode enabled.

will this do?

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-Blockchain-Compute-Release-Notes.aspx

what's weird is im mining other coins at max hash rate, it's only etc that dips bad.

[P00P135]

Wondering if anyone can shed some light on my issue, im switching over to ETC and ive always used claymore.

my nvidia 1060 rigg pushes out the same hash rate 24.5 per card, my amds all went from 29.5 to 19.5. any idea what it can be?

Use amd blockchain drivers from 23 August or if you Use latest version of Windows 10 give a try to latest relive drivers with compute mode enabled.

will this do?

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-Blockchain-Compute-Release-Notes.aspx

Yes this is what you should use until the latest drivers with compute mode is less buggy.

[Victorio]

To anyone whose rigs started freezing and crashing recently - just check your Windows update logs, especially on Win 10.
You can use Win 10 Spy Disabler to optimize Windows and disable unnecessary features.

[jimmykl]

Im a beginner Miner.....whats a good GPU to start out with?

gtx 1070 or AMD 580

for the same budget buy 2 gtx 1060 3GB and earn 50% more ...

Yeah right... and gift them for 50 euros each in the second hand market after some months that 3GB won't be enough for dag files....

BONUS with 1060 3GB option: Crappy Hynix memory chips averaging 18MH/s....

(Pssssst equihash etc)

[SummersideGuy]

To anyone whose rigs started freezing and crashing recently - just check your Windows update logs, especially on Win 10.
You can use Win 10 Spy Disabler to optimize Windows and disable unnecessary features.

I am using Win 7, I didnt bother looking into anything, I just Reinstalled Windows, it is all running again will see if it works out. Will update in another 24hours if it continues to run ok

[ushba_yu]

Dear Claymore!
Is it possible to add to remote monitor possibility to understand computer's names instead of IP?
It will be usefull for many admins.
For example, I have to control about 140 rigs. Time to time, IP-adresses of rigs are changed by DHCP.
So, 1 or 2 times a  week I need to reconfigure remote monitoring.  
It's really terrible job!  

Thank you in advance!

[Ursul0]

Dear Claymore!
Is it possible to add to remote monitor possibility to understand computer's names instead of IP?
It will be usefull for many admins.
For example, I have to control about 140 rigs. Time to time, IP-adresses of rigs are changed by DHCP.
So, 1 or 2 times a  week I need to reconfigure remote monitoring.  
It's really terrible job!  

Thank you in advance!

ever heard of static ips? you can easily fix this issue yourself