Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[Claymore]

I know what screenshot and log is. Just wanted to show the issue.

Finally I see the log.
From the log I see you have 3 ETH pools. After every 3 attempts miner switches to new pool. May be all pools have same IP, I don't know it, I have no idea why you cleared IP because 192.168.x.x addresses are not public, they are not routed. Anyway, 3 or 6 attempts mean that miner changed pool 1 or 2 times. To make a "clean" test, try to remove all settings from command line or config.dat and leave one pool in epools.txt as I described in previous message.
Also before starting miner it's a good idea that geth is working (and may be test it with some different miner). In my tests miner always starts working at first attempt.
I can add option to change the delay between attempts, but I'm not sure if it really necessary, you are the first person who want to have it.

hey Claymore, nice miner!
Maybe you can add to EthMan feature to reduce intensity for a particular gpu?

Already done, check Readme or OP for "-li" option.

[xeridea]

Hello

Its a 1300w edga gold power supply enough to dual mining with  6x of msi r9 390x?

Not really, you will need to undervolt a lot and maybe underclock, and run low -dcri. Even then you are pushing limits of it, consider dual PSUs.  Their total TDP is 1650w.  Someone on this forum does it, and it is very unstable.

Hello,

And 1300w for 4x msi r9 390x its possible?

4 would probably work, would still want to undervolt just to lessen load a bit.

how much i undervolt?

As low as possible without it crashing...

I would get a killawatt meter ($20), and test wattage at wall, then factor in PSU efficiency, and try to keep PSU under 80% capacity.

[qqqq]

I know what screenshot and log is. Just wanted to show the issue.

Finally I see the log.
From the log I see you have 3 ETH pools. After every 3 attempts miner switches to new pool. May be all pools have same IP, I don't know it, I have no idea why you cleared IP because 192.168.x.x addresses are not public, they are not routed. Anyway, 3 or 6 attempts mean that miner changed pool 1 or 2 times. To make a "clean" test, try to remove all settings from command line or config.dat and leave one pool in epools.txt as I described in previous message.
Also before starting miner it's a good idea that geth is working (and may be test it with some different miner). In my tests miner always starts working at first attempt.
I can add option to change the delay between attempts, but I'm not sure if it really necessary, you are the first person who want to have it.

I got ETC and ETH geth on different IP. It was off one geth specially for the reproduce the issue. But there is no issue actually. 3 attempts to connect and change the IP according epools.txt

Here my epools

POOL: http://192.168.100.88:8545
POOL: http://192.168.100.2:8545

Sometimes geth crushed due DDOS, so why i need 1 minute for that. Anyway request flag to reduce time between attempts to connect and ethman tray icon total hashmeter.  

[Claymore]

Sometimes geth crushed due DDOS, so why i need 1 minute for that. Anyway request flag to reduce time between attempts to connect and ethman tray icon total hashmeter.  

It's good if you found that the problem is not in miner. Use Parity when possible, it works much better than geth, really.
What about tray hashmeter? I have no clue what you mean, sorry.

[Bakery]

Sometimes geth crushed due DDOS, so why i need 1 minute for that. Anyway request flag to reduce time between attempts to connect and ethman tray icon total hashmeter.  

It's good if you found that the problem is not in miner. Use Parity when possible, it works much better than geth, really.
What about tray hashmeter? I have no clue what you mean, sorry.

I think he means that you can see hashrate in the system tray i.e near the clock down bottom right on the taskbar.

[qqqq]

Sometimes geth crushed due DDOS, so why i need 1 minute for that. Anyway request flag to reduce time between attempts to connect and ethman tray icon total hashmeter.  

It's good if you found that the problem is not in miner. Use Parity when possible, it works much better than geth, really.
What about tray hashmeter? I have no clue what you mean, sorry.

I use the parity but i don't like it much. It has problem sometimes when DDOS too.

This is Msi afterburner icons of GPU temps. I want total hashrate icon from ethman 

[Claymore]

I use the parity but i don't like it much. It has problem sometimes when DDOS too.
This is Msi afterburner icons of GPU temps. I want total hashrate icon from ethman 

Tray is noot good place for numbers 100 and higher. Only two digits are good there. So may be set target total hashrate in EthMan and show % of target hashrate in tray.

[qqqq]

I use the parity but i don't like it much. It has problem sometimes when DDOS too.
This is Msi afterburner icons of GPU temps. I want total hashrate icon from ethman 

Tray is noot good place for numbers 100 and higher. Only two digits are good there. So may be set target total hashrate in EthMan and show % of target hashrate in tray.

Ok, i see. It would be nice.

[blue1984]

someone tested the new driver? 16.10.1 ?


http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-Edition-16-10-1-Release-Notes.aspx

[fittsy]

It works with Wallet address and without, but after 6 tries at 20 sec. How i can reduce time between checking or number of tries ?

At least it works, thank you for help.

I need to see log file

So please add flag for choosing time between tries or number tries.

192.168.X.X is private anyway. No need to hide that range from us. LOL.

It is not publicly accessible ip. Only internal.

LOL

[jadefalke]

@Claymore do sell your Miner so that there is no Fee?

[Claymore]

@Claymore do sell your Miner so that there is no Fee?

No. All my miners are public, I don't sell private miners.

[thevictimofuktyranny]

@Claymore do sell your Miner so that there is no Fee?

No. All my miners are public, I don't sell private miners.

Are you taking part in the Zcash (ZEC) public open source mining software contest - ends 27th October?

£10,000 prize for GPU miner
£10,000 prize for CPU miner

And, £10,000 in prizes going to the runners up?

[peoples]

Running v7.2 on ubuntu 16.04 and i'm faceing more and more of opencl hang errors:

Code:

WATCHDOG: GPU 1 hangs in OpenCL call, exit

This doesn't seem to be card or riser related because its randomly.
Doe anyone experience the same or has an idea ?

Thanks

[citronick]

Running v7.2 on ubuntu 16.04 and i'm faceing more and more of opencl hang errors:

Code:

WATCHDOG: GPU 1 hangs in OpenCL call, exit

This doesn't seem to be card or riser related because its randomly.
Doe anyone experience the same or has an idea ?

Thanks

what the most stable CDM version on Linux build, for AMD cards only?

[peoples]

Running v7.2 on ubuntu 16.04 and i'm faceing more and more of opencl hang errors:

Code:

WATCHDOG: GPU 1 hangs in OpenCL call, exit

This doesn't seem to be card or riser related because its randomly.
Doe anyone experience the same or has an idea ?

Thanks

what the most stable CDM version on Linux build, for AMD cards only?

don't know.
Have also lots of 390 Rigs with CDM 7.2 running fine. So maybe RX driver related ? Cause R9 cards useing crimson driver.

[Trimegistus]

Guys, I'm using AMD 16.9.1 driver and my rigs are super stable.

Not planning to update but I was wondering if someone has any experience with the latest driver?

Maybe some speed improvement... 

[losk22]

What is the command line to run the miner to GF1070 ? Please bat file?

[bit815792215]

anyone experience a problem with motherboard slot bandwidth limiting card performance? I know mining shouldnt be affected by lane bandwidth, i think ? Gigabyte g board 1150, card is a msi 470 with polaris edit bios 1375 strap in 1625, 1750, and 2000. Card is in the last x1 slot on the board. With eth intensity 8 the card shows a lower hashrate than the other 3 that have the same strap, but with ethi 16 it is on par with the other ones. The others mine fine. I changed the strap for the weak card to 1500 just to see if it will be stable, it was stable with stock and small overclock using 1375 strap though. Will change it with a 16 slot to see it will be stable. Changed the riser as well, but still didn't help. Either way wte, but if it is stable in a 16 slot with 1375 strap that would be interesting. OS is windows 10.

edit, seems that the problem card is now stable with 1500 strap, but I still think there is problem with lanes, 27 mh, sia dcri 22. 1100/1900. Other cards with 1375 strap are getting 28+ mh, 1100/1900. GPU z showing 90 watts from gpu on all.

[m0niker]

What systems support up to 32 gpus? o_0