Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[StephdeLyon]

I changed for new amd official win7-crimson-relive-beta-blockchain-workloads-aug11 driver and patched with atimdag-patcher 1.4.5 (bios modded only mem straps),
Claymore 9.8 crashing at start (just after listing cards and "POLO/SOLO version" caption). It crash with stock settings or changed with OverdriveNTool 0.1.3....

Have anyone similar problem? Is that driver problem, claymore problem, other problem? was working before - 5x rx480, win7 x64

same problem for me but stock cards, same driver 17.7.2, no overclocking
ok on 3 cards , but crashes with 4 at the same moment.

don't know why...

put the stock GC bios or try on 3-4 cards  ?

[chronek]

put the stock GC bios or try on 3-4 cards  ?

I lost original bios so can not try it, tryed on 3 cards - the same crash

[okiagr]

AMD Blockchain driver + Claymore 9.8
Gigabyte RX 580 moded

- setting a target temperature value: if the temp is higher, the fan speed is increased but does not decrease when the temp lowers. For other cards in the temp limit, fans are constant
- voltage in bat file not working
- clock speed triggers fluctuation: it goes to 2100 (or whatever set) and back to 1000 and so on. If not set, it works.

[InfinyTank]

Hi all! Please give advice! I am trying to enjoy my rig as this is my computer too for almost everything, at least until I don't buy another one. I have 4x Rx580, but I would like to be able to watch movies/videos on my main card. I have tried "-ethi" parameter on this card, but it seems it doesn't work, or maybe I have added it incorrectly, in my command line for this I have set -ethi 5,8,8,8 as 8 is the maximum ether mining intensity and I lowered the first card. It looks nice, but in reality does not work. I wouldn't like to turn off the card completely with pressing "0". Please help!

[S1lent]

Hello guys,

I'm new to the ethermining community, trying to read everything and get it to work by myself. If I read through the topics and see those logs, I see I have a much different screen than all of you guys.

First my miner restarted itself because of my 2nd gpu, but disabling got the miner to run. But I only get the following lines:

ETH: 08/16/17-14:12:39 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 19.296 Mh/s, Total Shares: 3, Rejected: 0, Time: 00:09
ETH: GPU0 19.296 Mh/s, GPU1 off
ETH: 08/16/17-14:12:41 - SHARE FOUND - (GPU 0)
ETH: Share accepted (31 ms)!

This keeps repeating over and over.

Nothing else is basically happening. The GPU seems to work, but I'm not sure if what is happening is good, or that I did something wrong and that nothing is actually happening.

Sorry for my incompetence, don't slaughter me

[H0RNET]

Hello guys,

I'm new to the ethermining community, trying to read everything and get it to work by myself. If I read through the topics and see those logs, I see I have a much different screen than all of you guys.

First my miner restarted itself because of my 2nd gpu, but disabling got the miner to run. But I only get the following lines:

ETH: 08/16/17-14:12:39 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 19.296 Mh/s, Total Shares: 3, Rejected: 0, Time: 00:09
ETH: GPU0 19.296 Mh/s, GPU1 off
ETH: 08/16/17-14:12:41 - SHARE FOUND - (GPU 0)
ETH: Share accepted (31 ms)!

This keeps repeating over and over.

Nothing else is basically happening. The GPU seems to work, but I'm not sure if what is happening is good, or that I did something wrong and that nothing is actually happening.

Sorry for my incompetence, don't slaughter me

try -r 0 -di 0

[AzzAz]

I changed for new amd official win7-crimson-relive-beta-blockchain-workloads-aug11 driver and patched with atimdag-patcher 1.4.5 (bios modded only mem straps),
Claymore 9.8 crashing at start (just after listing cards and "POLO/SOLO version" caption). It crash with stock settings or changed with OverdriveNTool 0.1.3....

Have anyone similar problem? Is that driver problem, claymore problem, other problem? was working before - 5x rx480, win7 x64

same problem for me but stock cards, same driver 17.7.2, no overclocking
ok on 3 cards , but crashes with 4 at the same moment.

don't know why...

put the stock GC bios or try on 3-4 cards  ?

Or your mobo needs latest bios ( and bios setup ) or some connector is not properly connected

[JustCauseBIH]

Or 100% OC software need update

[S1lent]

Hello guys,

I'm new to the ethermining community, trying to read everything and get it to work by myself. If I read through the topics and see those logs, I see I have a much different screen than all of you guys.

First my miner restarted itself because of my 2nd gpu, but disabling got the miner to run. But I only get the following lines:

ETH: 08/16/17-14:12:39 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 19.296 Mh/s, Total Shares: 3, Rejected: 0, Time: 00:09
ETH: GPU0 19.296 Mh/s, GPU1 off
ETH: 08/16/17-14:12:41 - SHARE FOUND - (GPU 0)
ETH: Share accepted (31 ms)!

This keeps repeating over and over.

Nothing else is basically happening. The GPU seems to work, but I'm not sure if what is happening is good, or that I did something wrong and that nothing is actually happening.

Sorry for my incompetence, don't slaughter me

try -r 0 -di 0

I did the -di 0, makes it easier than doing it manually. But my question is about what basically happens after that. The miner keeps repeating those lines, nothing else is happing, so I'm not sure if my rig is actually mining or only receiving jobs without doing anything.

Edit: Just read the following line in the ReadMe, missed it earlier

You will not see full hashrate on pool immediately, you have to wait for 24 hours at least.

I guess I need to wait >24h to see any results?

[Wicard]

I changed for new amd official win7-crimson-relive-beta-blockchain-workloads-aug11 driver and patched with atimdag-patcher 1.4.5 (bios modded only mem straps),
Claymore 9.8 crashing at start (just after listing cards and "POLO/SOLO version" caption, in log after "start building OpenCL program for GPU 0..").
It crash with stock settings or changed with OverdriveNTool 0.1.3....

Have anyone similar problem? Is that driver problem, claymore problem, other problem? was working before - 5x rx480, win7 x64

I had the same issue, I had to use DDU then reboot install the BETA Driver and then reboot, then pixel patcher then reboot again, after that it worked fine,

I did found one PC hang after 2 hours but this is quite normal for me because it always happens after I changed stuff, restarted again and will see if it happens again.

also use afterburner BETA 16 within settings make sure Unlock voltage control is ticked and next to it select third party, that's if you use claymore for undervolting.

[androstan1234]

I cannot even install the driver.  I ran ddu, restarted, then tried to install the driver.  Partway through installation I get a blue screen with stop code "SYSTEM THREAD EXCEPTION NOT HANDLED," and saying that atikmpag.sys failed.

[cdrx]

Claymore 9.8
AMD Driver [Suspicious link removed]p*ute
Gigabyte RX 580 Gaming 8 GB

Voltage doesn't work with Wattman and AB beta 16 or Trixx.

[Wicard]

I cannot even install the driver.  I ran ddu, restarted, then tried to install the driver.  Partway through installation I get a blue screen with stop code "SYSTEM THREAD EXCEPTION NOT HANDLED," and saying that atikmpag.sys failed.

I had the same issue but that was without DDU use, I tried to update the driver by installing it over the other one, after reboot I used DDU and it worked make sure you reboot after each step..

[nadrojcote]

hello
i have a big problem with the last version and all over miners. works with 3 cards and when i want to put 4 gpu cards on my rig, it crashes...
all the same cards, Under win10 fresh installed, AMD driver 17.4.4, stock cards, psu 1200w seasonic prime on asrock H81 rev2

risers are ok because:
- gpu 1+2+3 => ok
- gpu 1+2+4 => ok
- gpu 1+2+3+4 => ko...

claymore start well and detect the 4 gpu's but crashed before to start mining, just after GPU detect.

please help me !!

- Make sure the card is not sharing power with another card
- Make sure each riser not sharing its power with another riser
- Run all cards on stock BIOS and stock seetings
- Uninstall MSI AB or similar software
- Run DDU in safe mode
- Reinstall AMD driver, the latest
- Run Claymore with minimal settings -cvdcc 1000 -mvdcc 1500

Share results and screenshots from GPU-Z

hello,
i did everything and its still the same problem... im running now Under 4 cards and it's crashing.
Under GPUZ i don't see any problem and all the cards are detected. no time to post screenshots for the moment.
any idea ?

i put under 2 cards, i've got another problem about drivers, perhaps it's my problem, with 2 cards, on pciexpress 1 and 2,
one cards is Under Crimson 17.7.2 / whql /win10 64 drivers (opencl ticked)
and the second one is only whql / win10 64 drivers (opencl not ticked)

Did you run DDU? be honest...

of course i did it !
i had to go to my job this morning, not enought time sorry.
here is the screenshot with one card, it seem that there an exclamation behind my card. Conflict between windows drivers and AMD driver ??
do i have to use DDU each time i add a card and re install crimson AMD drivers 17.7.2 ?
https://www.noelshack.com/2017-33-3-1502867786-capture.png

i tried to use simplemining and it does not work well at all... only 10mhs with 3 cards and gpu core often low at 300 instead of 1236, really strange. I had the 300mhz issue yesterday and it was afterburner causing the issues. I pressed the reset button in afterburner and the clock went back up. Some say online to remove afterburner and reinstall it.

I believe you have two problems. First of all you need to reset all you afterburner settings if you are using it. Or if you are using any other overclock software just uninstall it until you get things sorted.

Then your 4th card is probably not showing up because of the motherboard bios. You need to make sure above 4g decoding is enabled. Some mobo brands call it something else. Some don't support it.

[johndoe2]

Hello. Thank you to all the devs for creating such a great miner.
I was trying to dual mine with siacoin and it kept giving me this error.  Server: bind failed with error: 10048
I added the last two lines from beginning of this thread, and it kept giving me error. please help.


setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool asia1.ethermine.org:4444 -ewal 0xbF5498Dcb68228c314BE963d4f0913F2dyAdF23E.Miningrig2 -epsw x
 ethpool, ethermine  (and Siacoin pool):
EthDcrMiner64.exe -epool us1.ethpool.org:3333 -ewal 0xD69af2A796A737A103F12d2f0BCC563a1390oE6F.YourWorkerName -epsw x -dpool http://sia-eu1.nanopool.org:9980/miner/header?address=3be0304dee313515cf401b8593a0c1df905ed13f0adaee89a8d7337d2ba8209e5ca9f297bbc2 -dcoin sia

[okiagr]

Claymore 9.8
AMD Driver [Suspicious link removed]p*ute
Gigabyte RX 580 Gaming 8 GB

Voltage doesn't work with Wattman and AB beta 16 or Trixx.

same here, same cards

[nadrojcote]

Hello. Thank you to all the devs for creating such a great miner.
I was trying to dual mine with siacoin and it kept giving me this error.  Server: bind failed with error: 10048
I added the last two lines from beginning of this thread, and it kept giving me error. please help.


setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool asia1.ethermine.org:4444 -ewal 0xbF5498Dcb68228c314BE963d4f0913F2dyAdF23E.Miningrig2 -epsw x
 ethpool, ethermine  (and Siacoin pool):
EthDcrMiner64.exe -epool us1.ethpool.org:3333 -ewal 0xD69af2A796A737A103F12d2f0BCC563a1390oE6F.YourWorkerName -epsw x -dpool http://sia-eu1.nanopool.org:9980/miner/header?address=3be0304dee313515cf401b8593a0c1df905ed13f0adaee89a8d7337d2ba8209e5ca9f297bbc2 -dcoin sia

You don't have the correct address for your sia pool.

it should look like this. 

-dpool stratum+tcp://sia-eu1.nanopool.org:7777 -dwal YOUR_SIA_ADDRESS/YOUR_WORKER_NAME/YOUR_EMAIL -dcoin sia

[Wicard]

Claymore 9.8
AMD Driver [Suspicious link removed]p*ute
Gigabyte RX 580 Gaming 8 GB

Voltage doesn't work with Wattman and AB beta 16 or Trixx.

Here is my screen capture,

Using Claymore V9.7 not V9.8

http://funkyimg.com/i/2ws54.png

[kkourmousis]

Is there anyone here that tried to undervolt and overclock using Claymore's miner (any version) with the new official Beta drivers?

[chronek]

I changed for new amd official win7-crimson-relive-beta-blockchain-workloads-aug11 driver and patched with atimdag-patcher 1.4.5 (bios modded only mem straps),
Claymore 9.8 crashing at start (just after listing cards and "POLO/SOLO version" caption, in log after "start building OpenCL program for GPU 0..").
It crash with stock settings or changed with OverdriveNTool 0.1.3....

Have anyone similar problem? Is that driver problem, claymore problem, other problem? was working before - 5x rx480, win7 x64

I had the same issue, I had to use DDU then reboot install the BETA Driver and then reboot, then pixel patcher then reboot again, after that it worked fine,

I did 2 times - run in safe mode, run DDU, reboot, install official amd beta driver, reboot, use pixel patcher, reboot, claymore 9.8 crash when try build opencl program...
I have windows 7, saw couple posts that there is problem on that os, is amd working with microsoft for push windows 10? (warning tinfoil theory)