Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[tf2addict]

Suggestion:  red colored text should be used ONLY for error messages.  Use yellow for warning type messages.

[1715286949]

1715286949

[memphiss]

hey i did find this address :

https://ethermine.org/miners/e47FB8ED4aD43Ec67f11c146662191E145346C71


What do you think ? How is this possible?
He is playing with that graph ... he can write a name there if he want's ))

[Ratledge]

Hello, nice tip... I’m using the -r 0 config in start.bat and works well... not perfectly, but works.

Well, that is the default, though - you don't need to specify "-r 0" because it will restart when a GPU error occurs or one of the watchdog threads times out.

[AlexSandor]

Is this thread compromised then?

[muzuca]

Hello, nice tip... I’m using the -r 0 config in start.bat and works well... not perfectly, but works.

Well, that is the default, though - you don't need to specify "-r 0" because it will restart when a GPU error occurs or one of the watchdog threads times out.

Yeah, you’re right. I was using -r 1 and then changed to 0 and I forgot that is default. Thanks.

[xeridea]

...how does the remote monitoring work? Should I open a port in the rig's firewall (windows) and then type 192.168.X.XX:3333 in the browser of any computer of my network?

In the miner folder there is a folder called "Remote Manger". There is a program in there.  Enable monitoring (default port is -3333 (read only)). You can also use browser to just see current output. You don't need to open firewall port if on the same network, just allow miner access first run. If opening port to the outside world, and using positive port (full control), make 110% sure you set -mpsw, there are people that run bots to find miners and overwrite config. You can easily change config remotely with full control which is quite useful, just use locally, or use password.

[xeridea]

hi everybody,

I just join the mining community. I have 2 RX 480 8GDDR5 (1 Asus and 1 MSI) but the problem is that with one of them I reach 25Mh/s and with the other one only 18Mh/s.

Why is this happen? Anyone can help me with that issue?

thx a lot

Use GPU-Z to check memory vendor. I assume the Asus one probably has Samsung, MSI one probably Hynix. You can bios mod to get better speed by using better memory timings. Most cards should hit at least 27-28MH with custom timings, or at least 26MH with simple memory strap copy and a bit of OC. Use HwInfo64 to check memory errors.

As far as memory quality goes, Hynix < Elpida < Samsung.

Both of them have Samsung memory.


For what I see here I think everything is almost the same.

Do you now any good "How to bios update for dummies" tutorial that I can follow?

Without bios mod, going above stock generally makes use of looser timings, which may cause mining to be slower than stock, perhaps the slower miner has this issue.

Just search youtube for polaris bios mod.

In my experience, without pushing clock to high, I can get
~28MH Hynix (~1950 MHz) custom strap
~29MH Elpida (~2000 Mhz) Custom strap
~30MHz Samsung (2030MHz) Ubermix 2.3

Basically use atiflash to pull bios, edit with polarisbioseditor, flash card, run ati pixel clock patcher to remove driver gpu bios check, restart.

Links and timings here.
http://www.overclock.net/forum/67-amd-ati/1604567-polaris-bios-editing-rx5xx-rx4xx.html

Make sure to check mem errors HwInfo64

[whoismoses]

Is anyone out there using the configuration file instead of command line options?

When using 10.6 I get these warnings on startup of the miner...

Code:

UNKNOWN OPTION -platform
UNKNOWN OPTION 1
UNKNOWN OPTION -logsmaxsize
UNKNOWN OPTION 256

[The_Krypto_King]

Hello everybody how do I find out what the latest version of Claymore is that I can mine ETH with is this 10.6 or 10.3 and where is the official download link. Thans a lot!

[whoismoses]

Hello everybody how do I find out what the latest version of Claymore is that I can mine ETH with is this 10.6 or 10.3 and where is the official download link. Thans a lot!

It's in the first post of this thread.

[Mattdk]

Anyone had a problem with their GPU usage not being consistent and not at a high percentage? This is on a RX480 on stock bios, stock clocks, and tried blockchain, Adrenalin, and Crimson drivers. Hash rate is only 15 Mh/s

https://imgur.com/0w1X8Xx

[The_Krypto_King]

Thank you kind sir didn't realize that.

[aizzaku]

Anyone had a problem with their GPU usage not being consistent and not at a high percentage? This is on a RX480 on stock bios, stock clocks, and tried blockchain, Adrenalin, and Crimson drivers. Hash rate is only 15 Mh/s

https://imgur.com/0w1X8Xx

open up your card, clean all the dirt, trust me there will shit ton of it. apply new thermal paste and then check again.
try to keep the card temperature atleast below 80.

you have to do this like once every two months

[Marvell2]

Anyone had a problem with their GPU usage not being consistent and not at a high percentage? This is on a RX480 on stock bios, stock clocks, and tried blockchain, Adrenalin, and Crimson drivers. Hash rate is only 15 Mh/s

https://imgur.com/0w1X8Xx

open up your card, clean all the dirt, trust me there will shit ton of it. apply new thermal paste and then check again.
try to keep the card temperature atleast below 80.

you have to do this like once every two months

Ive had many of my GPUs for 2-3 years never had to do that, dont let dust build up clean them every few months , I will RMA those bitches before i waste my time re-applying thermal past lol

[aizzaku]

Anyone had a problem with their GPU usage not being consistent and not at a high percentage? This is on a RX480 on stock bios, stock clocks, and tried blockchain, Adrenalin, and Crimson drivers. Hash rate is only 15 Mh/s

https://imgur.com/0w1X8Xx

open up your card, clean all the dirt, trust me there will shit ton of it. apply new thermal paste and then check again.
try to keep the card temperature atleast below 80.

you have to do this like once every two months

Ive had many of my GPUs for 2-3 years never had to do that, dont let dust build up clean them every few months , I will RMA those bitches before i waste my time re-applying thermal past lol

well honestly depends on where the setup is. there are places in the world where no matter how hard you try you cant avoid dust, unless its a special air conditioned room.

secondly, i dont feel thats waste of my precious 15 mins -.-

[Marvell2]

Anyone had a problem with their GPU usage not being consistent and not at a high percentage? This is on a RX480 on stock bios, stock clocks, and tried blockchain, Adrenalin, and Crimson drivers. Hash rate is only 15 Mh/s

https://imgur.com/0w1X8Xx

open up your card, clean all the dirt, trust me there will shit ton of it. apply new thermal paste and then check again.
try to keep the card temperature atleast below 80.

you have to do this like once every two months

Ive had many of my GPUs for 2-3 years never had to do that, dont let dust build up clean them every few months , I will RMA those bitches before i waste my time re-applying thermal past lol

well honestly depends on where the setup is. there are places in the world where no matter how hard you try you cant avoid dust, unless its a special air conditioned room.

secondly, i dont feel thats waste of my precious 15 mins -.-

Dust is everywhere ,  but 15 mins x 200 gpus is better to just RMA

[MrDeity]

Hello there! Claymore can't mine on ethermine pool!!!

TH: Stratum - Cannot connect to eu1.ethermine.org:4444
ETH: Stratum - Failed to connect, retry in 20 sec...

I changed  stratum servers to s1.ethermine.org:4444, asia1.ethermine.org:4444 or asia1.ethermine.org:14444

But it doesn't help

ETH: Stratum - Cannot connect to us1.ethermine.org:4444
ETH: Stratum - Failed to connect, retry in 20 sec...

Who else does have this issue?

same. for recover i use claymore 10.4
until they fix it.

Same problem at the same time in two rigs 

I have the same isues and I think that is a DNS problem, but I can not check it because I'm on private network that can not change the DNS , I make a proxy outside this network and I connected the proxy to the pool and now it's fine

I was having the same failed to connect issue too.  What worked for me was going into my antivirus' firewall settings and unblocking/allowing the EthDcrMiner64 file. 

[aluminummonster]

Hey guys i'm new and just wanted to share a problem I had in case anyone else who is new runs into the same problem. I was getting dcr job timeout disconnect retry in 20 sec error when trying to dual mine sia and eth and it was because I had the -dcoin on a different line which was causing the error.

I had it like this


EthDcrMiner64.exe -epool eu1.nanopool.org:9999 -ewal YOUR_ETH_WALLET/YOUR_WORKER/YOUR_EMAIL -epsw x -dpool stratum+tcp://sia-eu1.nanopool.org:7777 -dwal YOUR_SIA_WALLET/YOUR_WORKER/YOUR_EMAIL
-dcoin sia

[Verloren55]

I like this Miner, BUT 2 % devee is much too much. Claymore makes millions every month just with this little software. Is that fair? I'm willing to pay like 0.1 % but thats just greedy. I mine with the -nofee Option, its worth me instead of supporting greedy people.

[Treborn]

How to correctly setup Claymore 10.6 in SimpleMining.net for Ethermine.org? Im running 2 rigs of 6 x XFX 470 8Gb solo mining Ethereum in a ethermine.org and I have huge problems regarding reported hashrate vs average hashrate.

Im using the following command line:
-wd 0 -r -1 -epool stratum+tcp://eu1.ethermine.org:4444 -ewal 0xwallet.Miner -esm 0 -epsw x -allpools 1 -asm 1 -dcri 5

Explanation:
wd 0 // if one card is stuck because of bad riser or some other problem the minner keeps going.
r -1 // no restart except manually
epool // Stratum protocol
-esm 0 // should I use 1?
-epsw x // I should drop this
-allpools 1 // I guess this pays the devfee, correct?
-asm 1 // related to dcri option
-dcri 5 // is it really needed if I dont dual mine?

Thanks for your help Once I sort out the problem I`ll post the right command line so other can future use it.