atomant
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 07, 2018, 05:57:53 AM |
|
where can I report bugs for claymore? I went home from work last night, only to get an email from the system that the miner had gone offline. So,it was offline not generating income for 12 hours. I can attach the log file if needed. There's alot of info in it.
Also, I'd like to know if it's possible to mine XMR and ETH at the same time onthe DUAL Miner
|
|
|
|
deadsix
|
|
February 07, 2018, 09:06:30 AM |
|
-tstop set stop GPU temperature, miner will stop mining if GPU reaches specified temperature. For example, "-tstop 95" means 95C temperature. You can also specify values for every card, for example "-tstop 95,85,90". This feature is disabled by default ("-tstop 0"). You also should specify non-zero value for "-tt" option to enable this option. If it turned off wrong card, it will close miner in 30 seconds. You can also specify negative value to close miner immediately instead of stopping GPU, for example, "-tstop -95" will close miner as soon as any GPU reach 95C temperature.
Hey Clay, Feature request : -tstop stops the GPU that was overheating at the specified temperature, please add an option to re-enable it once it cools down. You could restart the miner using something like minspeed but that isnt the most efficient way of doing it, since only one GPU would need to be re-enabled.
|
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
|
February 07, 2018, 09:26:34 AM |
|
Hey Clay, Feature request : -tstop stops the GPU that was overheating at the specified temperature, please add an option to re-enable it once it cools down. You could restart the miner using something like minspeed but that isnt the most efficient way of doing it, since only one GPU would need to be re-enabled.
Ok, I will add -tstart option in next update.
|
|
|
|
Amkolino
Newbie
Offline
Activity: 42
Merit: 0
|
|
February 07, 2018, 09:48:40 AM |
|
ok guys it seems 3gb cards have officially stopped working on eth network. Dag erro etc etc, the 6gb cards in the same rigs are doing fine. surprising though is that under stats its says 2.4gb used for dag.
one by one all the 3gb rigs gave up.
or am i missing something?
increase your swap size with 10 ot 20 GB What do you mean with SWAP Size? :-/
|
|
|
|
BSAlex
Member
Offline
Activity: 239
Merit: 10
|
|
February 07, 2018, 09:50:32 AM |
|
Odd situation.
Have a rig with 3 x RX570 4GB. Was getting 27Mh/s with Claymore 10.6.
Had to change rig to different board and hard drive. Board is the same, hard drive is slightly different (slower, but didn't think this mattered). Same amount or RAM *GB, same pagefile, 16GB, same divers, same version of windows but now only getting 20Mh/s.
ANy ideas? Really frustrated.
Memory Clock - 1750 MHz Core Clock - 1244 MHz
Check for compute switch in the driver, by default it is NOT set to compute. You can try much higher mem clock. It is usually safe to try 2150, even more for select cards. I have experienced performance degrade when undervolting fail to set up, but not that much really. Check actual core and mem voltages and try to set to 950 mV and lower. Go one at a time and check for results. 27 is pretty low for RX570, try to find better bios settings.
|
|
|
|
dollos
Newbie
Offline
Activity: 30
Merit: 0
|
|
February 07, 2018, 11:33:22 AM |
|
my swap file is always set to 32gb min and upto 48gb if required.
this is the 3gb limit and nothing more. on etc, eth will hit limit soon too
|
|
|
|
GabriAmarath
Newbie
Offline
Activity: 1
Merit: 0
|
|
February 07, 2018, 11:57:04 AM |
|
Hi guys i'm still having the same truble as before with DCR mining,
DCR - Total Speed: 0.000 Mh/s, Total Shares: 1, Rejected: 0 DCR: GPU0 0.000 Mh/s Socket was closed remotely (by pool) DCR: Job timeout, disconnect, retry in 20 sec... ETH: 02/07/18-12:53:54 - New job from eu1.ethermine.org:4444 ETH - Total Speed: 12.165 Mh/s, Total Shares: 20, Rejected: 0, Time: 01:44 ETH: GPU0 12.165 Mh/s DCR: Stratum - connecting to 'pasc-eu2.nanopool.org' <51.255.34.80> port 15555 DCR: Stratum - socket send failed 10054, disconnect DCR: Stratum - Failed to connect, retry in 20 sec... ETH: 02/07/18-12:54:21 - New job from eu1.ethermine.org:4444 ETH - Total Speed: 12.154 Mh/s, Total Shares: 20, Rejected: 0, Time: 01:45 ETH: GPU0 12.154 Mh/s DCR: Stratum - connecting to 'pasc-us-east1.nanopool.org' <192.99.69.170> port 15555 DCR: Stratum - socket send failed 10054, disconnect DCR: Stratum - Failed to connect, retry in 20 sec...
What could I change?
thank in advance.
Gabri
|
|
|
|
Amkolino
Newbie
Offline
Activity: 42
Merit: 0
|
|
February 07, 2018, 11:57:41 AM |
|
my swap file is always set to 32gb min and upto 48gb if required.
this is the 3gb limit and nothing more. on etc, eth will hit limit soon too
https://investoon.com/tools/dag_sizeAccording to this, in 2019. I can live with that :-) Afterwards I could mine zec, zcl, zen, nicehash etc. with my 1060 3gb rigs or just sell them ^^
|
|
|
|
idontknowmining
Newbie
Offline
Activity: 11
Merit: 0
|
|
February 07, 2018, 12:51:52 PM |
|
Check for compute switch in the driver, by default it is NOT set to compute. You can try much higher mem clock. It is usually safe to try 2150, even more for select cards. I have experienced performance degrade when undervolting fail to set up, but not that much really. Check actual core and mem voltages and try to set to 950 mV and lower. Go one at a time and check for results. 27 is pretty low for RX570, try to find better bios settings.
Thanks, sorry for the more questions but: Check for compute switch in the driver, by default it is NOT set to compute - Can you tell me where this is, looked it up, can't find anything. 27 is pretty low for RX570, try to find better bios settings. - can you provide a link to better options?
|
|
|
|
MrDeity
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 07, 2018, 01:44:47 PM |
|
I have 3 GPUs (one Vega 64, two RX 580s) and I can only consistently keep the vega 64 and one RX580 connected after reboots. I've checked the risers (they appear to be good). I saw on youtube that sometimes the video cards don't work without them thinking that they have a video card attached so I have two monitors (or I can use the HDMI plugin that fakes a monitor). I have an older MOBO that should have the appropriate requirements but as I mentioned earlier, sometime I can get the rig to see the third card but sometimes I can't.
Any suggestions? Bumped for reference to my next post...
|
|
|
|
mshordja
|
|
February 07, 2018, 01:45:50 PM |
|
any news about the new version? i am really exiting to see the next dual mine coin
|
|
|
|
MrDeity
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 07, 2018, 01:54:23 PM |
|
When the card is not accessible do you get a yellow triangle sign in your device manager (if you use windows 10 e.g.)?
I hade some gtx 1070, they worked from time to time - then again they didn't. After some reboot they worked then they didnt etc..
Replaced the card, everything fine.. :-(
I do use Windows 10. The card is powered up (I can see the lights on the card) but I don’t see it at all on the device manager. If I disconnect one of the other cards, I can see it so I know the card is working but I’m having trouble getting all three to work at the same time.
|
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
|
February 07, 2018, 02:25:10 PM |
|
any news about the new version? i am really exiting to see the next dual mine coin I will release new version in 1-2 days.
|
|
|
|
Ratledge
Jr. Member
Offline
Activity: 84
Merit: 1
|
|
February 07, 2018, 02:28:36 PM |
|
increase your swap size with 10 or 20 GB
What do you mean with SWAP Size? :-/ Windows "Swap" file size = virtual memory settings in the control panel. Look up "adjust virtual memory size" using Google for you OS (assumed to be Windows 10?) and follow the instructions to increase the amount of available disk space for memory swapping.
|
|
|
|
fr4nkthetank
Legendary
Offline
Activity: 2294
Merit: 1182
Now the money is free, and so the people will be
|
|
February 07, 2018, 02:30:44 PM |
|
The suspense is killing me ! At the same time, I dont wish to upgrade all my rigs again... but progress is progress and we need more profits
|
|
|
|
mshordja
|
|
February 07, 2018, 02:33:28 PM |
|
any news about the new version? i am really exiting to see the next dual mine coin I will release new version in 1-2 days. thanks for the reply
|
|
|
|
MaryAngela_Fantocci
Sr. Member
Offline
Activity: 462
Merit: 252
Buy/Sell crypto at BestChange
|
|
February 07, 2018, 04:09:40 PM |
|
So decred, sia and pascal already has asic's? What about pascal and coins on the same algo?
|
|
|
|
Victorio
|
|
February 07, 2018, 05:25:18 PM |
|
we want to make two rig for this time. one is located in czech republic and one in germany. We want to mine in dodopool. I check txt and there is different spec in each pool. What do u advice? Mine separate or its possible to mine together?
Use the same miner commands for both rigs, except worker name: EthDcrMiner64.exe -epool stratum+tcp://etp.dodopool.com:8008 -ewal %EWAL% -eworker rigCZ -epsw x -allpools 1 -allcoins 1 EthDcrMiner64.exe -epool stratum+tcp://etp.dodopool.com:8008 -ewal %EWAL% -eworker rigDE -epsw x -allpools 1 -allcoins 1 OR Use the same epools.txt, modify just WORKER name: POOL: stratum+tcp://etp.dodopool.com:8008, WALLET: %EWAL%, WORKER: rigCZ, PSW: x, ESM: 0, ALLPOOLS: 1, ALLCOINS: 1 POOL: stratum+tcp://etp.dodopool.com:8008, WALLET: %EWAL%, WORKER: rigDE, PSW: x, ESM: 0, ALLPOOLS: 1, ALLCOINS: 1
|
|
|
|
RYXES
Member
Offline
Activity: 140
Merit: 10
Merit me or don't.
|
|
February 07, 2018, 05:30:10 PM |
|
any news about the new version? i am really exiting to see the next dual mine coin I will release new version in 1-2 days. Exciting. Best I blow off the cob webs of my dual mining Reg's.
|
Merit me or don't.
|
|
|
Xkeeper
Newbie
Offline
Activity: 5
Merit: 0
|
|
February 07, 2018, 06:13:41 PM Last edit: February 07, 2018, 06:57:44 PM by Xkeeper |
|
Hello
I have flashed the bios on my Sapphire Nitro+ RX570 4GB under Windows and I'm getting 30MH stable with Claymores.
But when I try same flashed card under Ubuntu I get only 21.2MH with Claymores
Any Idea what I might be missing? I realy dont want to end up mining under windows.
I'm running Xubuntu 16.04 Kernel 4.10.0-28 amdgpu-pro beta mining driver 17.40.3.12 Claymores 10.6
|
|
|
|
|