Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 10:33:31 PM |
|
Is it possible to have a mining board with removable mining chips (like CPU socket/slot)?
It would give you an edge over all other manufactures. I really want to support you against the Chinese manufactures.
It's possible to do so, but it would not be feasible or economical to do so. The Rockerbox ASIC is in a BGA (ball grid array) package, which allows for a very high density of electrical connections to the circuit board substrate, as well as lower inductance on the power input and better power decoupling with capacitors. They also conduct heat to the PCB better. Replacing that with a pin grid array socket would make the whole thing bulkier and more expensive. In order to upgrade ASICs, you'd need to keep the electrical signals the same on each generation of chips, which would require a lot of forethought and planning and would make it harder to advance technology with each generation. It would also complicate heatsink design. Using sockets instead of a BGA or QFP package would make the miner slightly slower and more expensive. Correct.
|
|
|
|
dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 10:53:01 PM |
|
Hi all, I just got a 15 unit batch of SP20's approximately 30 hours ago. I absolutely love these rigs!!! However, I am running into an issue with one rig. It says, "LOOP[0] ON TO:0 (w:38) 0: disabled (Asic all engines fail BIST). I have IBM 2880W PSU's with breakout boards. All of the others are running well on these IBM 2880W PSU's except for one I had problems connecting to last night [I will deal with it after I finish my new mining closet in the next couple of days]. I have replaced the PCI-e cord in port 1 of the SP20 and I've changed ports with a new cord on the breakout board. Yet, it still says, "LOOP[0] ON TO:0 (w:38) 0: disabled (Asic all engines fail BIST)." I was getting too sleepy last night to continue trouble shooting it. If someone else has had this issue or has something to offer for me to try, please chime in. Thank you ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FxHaOTQc.png&t=665&c=JYYN5K6VvmIxvQ)
|
|
|
|
dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 10:58:43 PM |
|
Douglas County PUD is 1.85 cents per kWH.
Do you know something I don't? From what I know, 2014 rates in Douglas are 2.35 cents, or about 2.52 cents once you factor in demand charges. When I talked to them in person last June, they said that rate applies to anything up to 5 MW, after which you have to buy wholesale power from the Bonneville Power Administration exchange (which is more expensive). http://www.douglaspud.org/Documents/Current%20Rates.pdfYes, there is a demand charge. But still dude, 2.35 cents!!! That beats the hell out of my 10.6 cents in the winter and 12.1 cents in the summer in Alabama. One can save $22,000.00 each month from a 550kW system versus what I'm paying here in Alabama. Alabama rates include demand charges, etc... I'm also aware of the "over 5 MW" exchange pricing.
|
|
|
|
dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:05:52 PM |
|
Any ideas what is up with this 243 degrees Celsius on Loop 0? I just got 15 rigs less than 24 hours ago.
There is an 8-bit unsigned integer underflow bug that occasionally manifests on Rockerbox (SP20/30/31/35) machines. Any VRM temperature reading that would be less than zero ends up as 255 minus the temperature reading. A temperature report of 243 thus probably means a reading of -12°C. There are a few other bugs that can cause abnormally low temperature readings. The most common one is due to the fact that Spondoolies uses several different models of FETs in their VRM blocks, and the different FET models have different temperature sensor calibrations. If the firmware uses the wrong sensor calibration formula, then you get temperature readings that are off by 20°C or so. Thank you, Sir! Very interesting! By the way, the firmware update did fix the problem.
|
|
|
|
jtoomim
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:12:00 PM |
|
Even moses lake is 3.28 cents
Actually, Grant County has several different rates depending on what type of customer you are. Our rate is $0.021/kWh for the first 50,000 kWh, and $0.018/kWh for each kWh thereafter, plus $4.69 per kW for the demand charge. Total comes to about $0.025. That's the Large General Service rate, which you can get if you're above 200 kW.
|
Hosting bitcoin miners for $65 to $80/kW/month on clean, cheap hydro power. http://Toom.im
|
|
|
jtoomim
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:15:41 PM |
|
I just got a 15 unit batch of SP20's approximately 30 hours ago. I absolutely love these rigs!!! However, I am running into an issue with one rig. It says, "LOOP[0] ON TO:0 (w:38) 0: disabled (Asic all engines fail BIST).
Bad ASIC. It may have been damaged during shipping, or it may just be a bad ASIC that slipped through QC. There's almost certainly nothing to be done besides replacing it. Spondoolies might be able to send you a replacement hashboard; you'd have to ask them.
|
Hosting bitcoin miners for $65 to $80/kW/month on clean, cheap hydro power. http://Toom.im
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:18:35 PM |
|
Hi all, I just got a 15 unit batch of SP20's approximately 30 hours ago. I absolutely love these rigs!!! However, I am running into an issue with one rig. It says, "LOOP[0] ON TO:0 (w:38) 0: disabled (Asic all engines fail BIST). I have IBM 2880W PSU's with breakout boards. All of the others are running well on these IBM 2880W PSU's except for one I had problems connecting to last night [I will deal with it after I finish my new mining closet in the next couple of days]. I have replaced the PCI-e cord in port 1 of the SP20 and I've changed ports with a new cord on the breakout board. Yet, it still says, "LOOP[0] ON TO:0 (w:38) 0: disabled (Asic all engines fail BIST)." I was getting too sleepy last night to continue trouble shooting it. If someone else has had this issue or has something to offer for me to try, please chime in. Thank you ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FxHaOTQc.png&t=665&c=JYYN5K6VvmIxvQ) Contact support@
|
|
|
|
dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:18:52 PM |
|
I just got a 15 unit batch of SP20's approximately 30 hours ago. I absolutely love these rigs!!! However, I am running into an issue with one rig. It says, "LOOP[0] ON TO:0 (w:38) 0: disabled (Asic all engines fail BIST).
Bad ASIC. It may have been damaged during shipping, or it may just be a bad ASIC that slipped through QC. There's almost certainly nothing to be done besides replacing it. Spondoolies might be able to send you a replacement hashboard; you'd have to ask them. Thanks, I suppose I need to get in touch with someone then. I have another rig that I cannot connect to at all. I know I have the correct IP address on it but it will not let me communicate with it. It just says the server will not let me connect to it. Any suggestions on that one?
|
|
|
|
notey
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 67
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:27:16 PM |
|
Hi Everyone,
I have the same problem as mentioned below. 10 SP31 units have been held in US Customs in Cincinnati for the last four days. Emailed Spondoolies but haven't heard back yet. Call into DHL and hope it can be resolved.
quote author=elduderino link=topic=521520.msg9893125#msg9893125 date=1419032066] Hey there,
I have kind of a funny story.
I ordered the 15 SP20 deal from the website and paid for it on the 5th. Figured I'd saved bunch of money from the shipping. I got a notice that it was shipped on the 10th.
From there it made it from Israel to Italy and Belgium on the 11th. On the 12th, it went through London, UK and on the 13th it left there, and made it to New York, NY on the 14th.
So far, so good.
From there: 14th, arrived at DHL's hub in Cincinnati, OH 15th, Clearance event, Cincinnati, OH 16th, Customs status updated, Cincinnati, OH 17th, Clearance event, Cincinnati, OH 18th, Customs status updated, Cincinnati, OH
I got a call from someone at DHL, who said they needed some information (for customs, ostensibly). I furnished the requested information, and the rep said I'd get it the next day (today). Now, I got an email from the Phoenix, AZ office that it will probably be held up for 'customs' for 4-5 days
I ordered (and paid for) it on the 5th, and I MIGHT get it in time to be an unexpected Christmas gift.
[/quote]
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:31:47 PM |
|
Hi Everyone,
I have the same problem as mentioned below. 10 SP31 units have been held in US Customs in Cincinnati for the last four days. Emailed Spondoolies but haven't heard back yet. Call into DHL and hope it can be resolved.
quote author=elduderino link=topic=521520.msg9893125#msg9893125 date=1419032066] Hey there,
I have kind of a funny story.
I ordered the 15 SP20 deal from the website and paid for it on the 5th. Figured I'd saved bunch of money from the shipping. I got a notice that it was shipped on the 10th.
From there it made it from Israel to Italy and Belgium on the 11th. On the 12th, it went through London, UK and on the 13th it left there, and made it to New York, NY on the 14th.
So far, so good.
From there: 14th, arrived at DHL's hub in Cincinnati, OH 15th, Clearance event, Cincinnati, OH 16th, Customs status updated, Cincinnati, OH 17th, Clearance event, Cincinnati, OH 18th, Customs status updated, Cincinnati, OH
I got a call from someone at DHL, who said they needed some information (for customs, ostensibly). I furnished the requested information, and the rep said I'd get it the next day (today). Now, I got an email from the Phoenix, AZ office that it will probably be held up for 'customs' for 4-5 days
I ordered (and paid for) it on the 5th, and I MIGHT get it in time to be an unexpected Christmas gift.
[/quote] When did you send us the email?
|
|
|
|
Meech
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 28, 2015, 11:42:43 PM |
|
Douglas County PUD is 1.85 cents per kWH.
Do you know something I don't? From what I know, 2014 rates in Douglas are 2.35 cents, or about 2.52 cents once you factor in demand charges. When I talked to them in person last June, they said that rate applies to anything up to 5 MW, after which you have to buy wholesale power from the Bonneville Power Administration exchange (which is more expensive). http://www.douglaspud.org/Documents/Current%20Rates.pdfEven moses lake is 3.28 cents Lovely place to visit but live... mmm meh. I'm not in to kickin dirt. Live on the other side of the mountains. But I would move in a heart beat to set up a farm there.
|
|
|
|
notey
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 67
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:01:41 AM |
|
Hello.E-mail was sent as below on to sales@spondoolies-tech Feb 27th at about 7AM. Not blaming Spondoolies and am sure I'll hear something next week. DHL Will probably help me work it out. Just wish we could avoid some of the shipping delays. I would have thought DHL a would have contacted me as soon as the delay occurred. I appreciate any help/advice. My shipment of (10) SP-31 miners from Spondoolies is apparently stuck in customs (Cincinnati, OH). The units were sent to me via DHL. What is the next step for me at this point? I wanted to have the miners ASAP and this delay is unfortunate. Thanks. Hi Everyone,
I have the same problem as mentioned below. 10 SP31 units have been held in US Customs in Cincinnati for the last four days. Emailed Spondoolies but haven't heard back yet. Call into DHL and hope it can be resolved.
quote author=elduderino link=topic=521520.msg9893125#msg9893125 date=1419032066] Hey there,
I have kind of a funny story.
I ordered the 15 SP20 deal from the website and paid for it on the 5th. Figured I'd saved bunch of money from the shipping. I got a notice that it was shipped on the 10th.
From there it made it from Israel to Italy and Belgium on the 11th. On the 12th, it went through London, UK and on the 13th it left there, and made it to New York, NY on the 14th.
So far, so good.
From there: 14th, arrived at DHL's hub in Cincinnati, OH 15th, Clearance event, Cincinnati, OH 16th, Customs status updated, Cincinnati, OH 17th, Clearance event, Cincinnati, OH 18th, Customs status updated, Cincinnati, OH
I got a call from someone at DHL, who said they needed some information (for customs, ostensibly). I furnished the requested information, and the rep said I'd get it the next day (today). Now, I got an email from the Phoenix, AZ office that it will probably be held up for 'customs' for 4-5 days
I ordered (and paid for) it on the 5th, and I MIGHT get it in time to be an unexpected Christmas gift.
When did you send us the email? [/quote]
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:03:57 AM |
|
Hello.E-mail was sent as below on to sales@spondoolies-tech Feb 27th at about 7AM. Not blaming Spondoolies and am sure I'll hear something next week. DHL Will probably help me work it out. Just wish we could avoid some of the shipping delays. I would have thought DHL a would have contacted me as soon as the delay occurred. I appreciate any help/advice. My shipment of (10) SP-31 miners from Spondoolies is apparently stuck in customs (Cincinnati, OH). The units were sent to me via DHL. What is the next step for me at this point? I wanted to have the miners ASAP and this delay is unfortunate. Thanks. Hi Everyone,
I have the same problem as mentioned below. 10 SP31 units have been held in US Customs in Cincinnati for the last four days. Emailed Spondoolies but haven't heard back yet. Call into DHL and hope it can be resolved.
quote author=elduderino link=topic=521520.msg9893125#msg9893125 date=1419032066] Hey there,
I have kind of a funny story.
I ordered the 15 SP20 deal from the website and paid for it on the 5th. Figured I'd saved bunch of money from the shipping. I got a notice that it was shipped on the 10th.
From there it made it from Israel to Italy and Belgium on the 11th. On the 12th, it went through London, UK and on the 13th it left there, and made it to New York, NY on the 14th.
So far, so good.
From there: 14th, arrived at DHL's hub in Cincinnati, OH 15th, Clearance event, Cincinnati, OH 16th, Customs status updated, Cincinnati, OH 17th, Clearance event, Cincinnati, OH 18th, Customs status updated, Cincinnati, OH
I got a call from someone at DHL, who said they needed some information (for customs, ostensibly). I furnished the requested information, and the rep said I'd get it the next day (today). Now, I got an email from the Phoenix, AZ office that it will probably be held up for 'customs' for 4-5 days
I ordered (and paid for) it on the 5th, and I MIGHT get it in time to be an unexpected Christmas gift.
When did you send us the email? [/quote] We'll contact DHL. Friday is our weekend.
|
|
|
|
nexus99
Legendary
Offline
Activity: 910
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:12:52 AM |
|
@ Spondoolies - When are you going to start selling hardware again?
|
|
|
|
notey
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 67
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:14:48 AM |
|
Understood. Looking forward to working with the new miners. I'll let you know what DHL asks for. I upgraded home panel to 400A and put in 220v 20A and 30A circuits. I have 24A safely usable on the 30A circuits (5280W) with the derated PDUs. Do you think I can run (2) SP31s on each of those circuits as long as I underclock them? quote author=Spondoolies-Tech link=topic=521520.msg10615913#msg10615913 date=1425168237] Hello.E-mail was sent as below on to sales@spondoolies-tech Feb 27th at about 7AM. Not blaming Spondoolies and am sure I'll hear something next week. DHL Will probably help me work it out. Just wish we could avoid some of the shipping delays. I would have thought DHL a would have contacted me as soon as the delay occurred. I appreciate any help/advice. My shipment of (10) SP-31 miners from Spondoolies is apparently stuck in customs (Cincinnati, OH). The units were sent to me via DHL. What is the next step for me at this point? I wanted to have the miners ASAP and this delay is unfortunate. Thanks. Hi Everyone,
I have the same problem as mentioned below. 10 SP31 units have been held in US Customs in Cincinnati for the last four days. Emailed Spondoolies but haven't heard back yet. Call into DHL and hope it can be resolved.
quote author=elduderino link=topic=521520.msg9893125#msg9893125 date=1419032066] Hey there,
I have kind of a funny story.
I ordered the 15 SP20 deal from the website and paid for it on the 5th. Figured I'd saved bunch of money from the shipping. I got a notice that it was shipped on the 10th.
From there it made it from Israel to Italy and Belgium on the 11th. On the 12th, it went through London, UK and on the 13th it left there, and made it to New York, NY on the 14th.
So far, so good.
From there: 14th, arrived at DHL's hub in Cincinnati, OH 15th, Clearance event, Cincinnati, OH 16th, Customs status updated, Cincinnati, OH 17th, Clearance event, Cincinnati, OH 18th, Customs status updated, Cincinnati, OH
I got a call from someone at DHL, who said they needed some information (for customs, ostensibly). I furnished the requested information, and the rep said I'd get it the next day (today). Now, I got an email from the Phoenix, AZ office that it will probably be held up for 'customs' for 4-5 days
I ordered (and paid for) it on the 5th, and I MIGHT get it in time to be an unexpected Christmas gift.
When did you send us the email? [/quote] We'll contact DHL. Friday is our weekend. [/quote]
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:16:44 AM |
|
|
|
|
|
dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:17:30 AM |
|
|
|
|
|
|
jtoomim
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:28:22 AM |
|
Understood. Looking forward to working with the new miners. I'll let you know what DHL asks for. I upgraded home panel to 400A and put in 220v 20A and 30A circuits. I have 24A safely usable on the 30A circuits (5280W) with the derated PDUs. Do you think I can run (2) SP31s on each of those circuits as long as I underclock them?
I've been using 1 SP30/SP31 each on 16 amp 237V circuits for a while with no problems. I can often stick a little extra on those circuits, like an underclocked SP10. Those are PDU circuits, though, and the breakers are built to international standards and aren't built for the 80% derating factor. Your 30A x 220V circuits are less than twice my 16 x 237V circuits, but I'd expect them to still work even at full speed. (Actually, come to think of it, each two 16A circuits is fed by one 30A circuit in our setup, so the only real difference is 237V vs 220V.) If you underclock your SP30s by 10% or 20%, you'll be quite safe. Speaking of underclocking...
|
Hosting bitcoin miners for $65 to $80/kW/month on clean, cheap hydro power. http://Toom.im
|
|
|
jtoomim
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 01, 2015, 12:28:43 AM Last edit: March 01, 2015, 12:50:33 AM by jtoomim |
|
Here's some data for you guys. http://toom.im/images/Spondoolies%20Hashrate.png http://toom.im/images/Spondoolies%20Efficiency.png http://toom.im/images/Spondoolies%20Marginal%20Hashrate.pngThe marginal efficiency graph shows the efficiency of a small increment in power. If you step the power consumption on an SP20 up from 1100W to 1200W, you only gain an extra 50 or so GH/s for 100 W in extra power consumption, giving a marginal efficiency of 2.0 J/GH. On the other hand, the overall efficiency at 1200W for an SP20 is about 0.75 J/GH. The marginal efficiency is a very useful metric for choosing what power settings to run a miner at. You should run your miners at a setting such that the marginal efficiency leaves you at the breakeven point. Right now, 1 TH/s earns about $0.111 per hour. If your power or hosting costs you $0.14/kWh, then your breakeven point would be [$0.111/(h•TH/s)] / [$0.14/kW•h] = 0.79 kJ/TH = 0.79 J/GH so you would want to run an SP20 at the setting that gives you a marginal efficiency of about 0.79 J/GH, which turns out to be about 600 W AC. Some notes: All tests were conducted on 240V +/- 5V with intake temperatures between 8°C and 18°C. The SP31s tested used Murata power supplies. The Murata PSUs are more efficient than the Emerson1200 PSUs (about 91.5% vs 88%). The SP30 tested used Emerson1200s. The SP20 used an HP DPS1200FB PSU, which appears to be 90% efficient on 240V. AC power consumption for the SP35, SP31, SP10 and SP20 were measured using a Dell PDU, and should be accurate to within 20W. AC power consumption for the SP30 was read off of the ASIC Stats page. Previous testing has shown the Emerson1200 and Emerson1600 (in the SP35) to give accurate AC consumption measurements compared to our PDUs. The DC power measurements of the SP10s and SP20s appear to be miscalibrated. At high power, they appear to be accurate, with our PDU measuring AC consumption that's about 10% higher than the reported DC power consumption. At low power (e.g. 60%), the SP10 reports DC power consumption 4% *below* the AC consumption, and the SP20 reports DC consumption equal to AC consumption. Power measurements from Murata power supplies show an inverse pattern, and are very inaccurate (and biased for low readings) at full power output, but tend to be accurate at 80% of max power or below. Do not rely on the power readings from SP10s, SP20s, and Murata SP30/31s for anything important. The SP10s tested were all from a moderately slow corner batch. A few of the max power datapoints might be missing from some machine types (e.g. SP10, SP35) to simplify testing. Most testing was done using voltage limiting (600 mV < start voltage = max voltage < 700 mV, or 750 mV for SP20). The SP30 was tested using power limiting, which is part of why its graph is slightly wavy. At very low voltages or power limits (< 620 mV, roughly, for both Rockerbox and Hammer), some ASICs on a machine will fail to start up. This results in rapidly dropping hashrate and power consumption towards the left end of the graphs, as well as potential system instability, with slight improvements in efficiency. Different ASICs will have vastly differing minimum voltages for operation, which means that some machines will be capable of much lower power operation when run at minimum voltage. I've seen a 25% (430W) difference in minimum power between two SP31s from the same batch, for example. However, the difference in efficiency between these machines at their minima was smaller, at 0.50 vs 0.45 J/GH. YMMV (your miners may vary). Data tables available upon request. Email j@toom.im if you want one. Specify which machine type(s) you want them for.
|
Hosting bitcoin miners for $65 to $80/kW/month on clean, cheap hydro power. http://Toom.im
|
|
|
|