Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux)

[atithasos]

Hehe  XFX Pro Duo 765h/s @430W 1150mhz

Lol this is great h/s
but the value cost is too too high
with the price of XFX Pro Duo I can have 6 rx 480
this means 1440sol
and i will also have some $ to spend also....

[cristipuc]

Any output for this card : MSI AMD R9 390X GAMING 8G LE ?

Thank you !

[halker2010]

omg 200 on 7950 and 160 on r9 380x you rock m8 

[dakky]

BTW anyone having problems with rejects? roughly 20% on 280x+290... 480 rigs work fine... there were not so much rejected on V8...

[vel12]

Any output for this card : MSI AMD R9 390X GAMING 8G LE ?

Thank you !

310 H/s

[cristipuc]

Any output for this card : MSI AMD R9 390X GAMING 8G LE ?

Thank you !

310 H/s

  Dou you have possibility to provide a screenshot ? sorry about asking this but i intend to buy few cards

[orangelemon]

all cards i6 stock clocks, changed timings on all exept 390X

How can i manage my all rigs like this.
show all rigs with cards model speed and temp
how you doing this what software using please tell me

[aimsml]

Hello.
3 graphics R9 380x - 511 H / s, without overclocking
Nice job mr. Claymore

[liomojo1]

Well i have a strange drawback than
280x
V8 -214-216
V9 - 205-6
What is going on?
-i2 for both

use a higher -i value

RTFM

Ok strange thing happens!
Non modified 280x Elpida mem, -I 8 gets 221sols
But my 5 Hynix 280x with modified straps , if i put -I above 3 , strange thing happens gpu 4 shows 0sol and gpu 0 shows 330SOLS which is insane , and there are many rejected shares, I restarted the miner and disabled all gpus except gpu0 and again it hashes with 331sols and many rejected shares , Claymore would you comment this phenomena!
-I 3 gives 220 to all and they work ok! BUT

[Claymore]

Well i have a strange drawback than
280x
V8 -214-216
V9 - 205-6
What is going on?
-i2 for both

use a higher -i value

RTFM

Ok strange thing happens!
Non modified 280x Elpida mem, -I 8 gets 221sols
But my 5 Hynix 280x with modified straps , if i put -I above 3 , strange thing happens gpu 4 shows 0sol and gpu 0 shows 330SOLS which is insane , and there are many rejected shares, I restarted the miner and disabled all gpus except gpu0 and again it hashes with 331sols and many rejected shares , Claymore would you comment this phenomena!
-I 3 gives 220 to all and they work ok! BUT

Yeah I can comment this. Don't modify bios and don't overclock cards too much. If you do it - you must know what you are doing and be ready to such problems. GPU does not work properly on complex algorithms and produces pure garbage instead of good results. Validating results will require CPU resources so I don't do it and you see that GPU shows crazy hashrate. But it is garbage.

[TalesofDeivid]

V8 XFX RX 480 192 h/s
V8 MSI RX 480 194 h/s
V9 XFX RX 480 220 h/s
V9 MSI RX 480 222 h/s

Good work Claymore! 

[issie81]

Guys,

using the Ethman do you really need to specify each miner by IP or can it just can the network and show the miner?
i don't see such option to scan the network (is way easier by more rigss.)

[AriesIV10]

all cards i6 stock clocks, changed timings on all exept 390X

How can i manage my all rigs like this.
show all rigs with cards model speed and temp
how you doing this what software using please tell me

Use after burner it will let you mix cards at there own timing and speed but you have to make sure to turn off two Settings if you use it
Synchronize the same cards uncheck or off and don't use extend over clocking limits, i found turning off those two setting in afterburner stops all my crashes and i can set all my cards separate from the other ones on the same RIg aka mixing cards .

That software is part of Claymmore look in the folder it's called Remote manager .

RX470x7 = 1.554 KH/s -i 8  Love It!

[toptek]

all cards i6 stock clocks, changed timings on all exept 390X

How can i manage my all rigs like this.
show all rigs with cards model speed and temp
how you doing this what software using please tell me

Use after burner it will let you mix cards at there own timing and speed but you have to make sure to turn off two Settings if you use it
Synchronize the same cards uncheck or off and don't use extend over clocking limits, i found turning off those two setting in afterburner stops all my crashes and i can set all my cards separate from the other ones on the same RIg aka mixing cards .

That software is part of Claymmore look in the claymore miner folder it's called Remote manager .

Guys,

using the Ethman do you really need to specify each miner by IP or can it just can the network and show the miner?
i don't see such option to scan the network (is way easier by more rigss.)

SO far no other way i see of doing it no scan button yet .

[chronek]

rig 5x sapphire nitro rx480 4gb 1306/1900 -96mV win7 doing 1140 sol/s, 760W at wall, best is all have 60-62'C with only 960-1300rpm fans

[Charloz24]

Someone here checked if v9 use more W? can't check it for now

[chronek]

Someone here checked if v9 use more W? can't check it for now

it use more W , like 4W more for rx480

[Pinocchio]

Version 9 can't be downloaded.

mega: loops "requesting folder data" - doesn't go to download page
google: "download quota exceeded for this file, you can't download at this time"

EDIT: managed to do it via mega, with the latest Firefox.

[th00ber]

R9 Fury NITRO on my rigs with same settings

V7 -> 230-235 H/s
V8 -> 275-280 H/s
V9 -> 305-310 H/s

[jddebug]

all cards i6 stock clocks, changed timings on all exept 390X

How can i manage my all rigs like this.
show all rigs with cards model speed and temp
how you doing this what software using please tell me

Use after burner it will let you mix cards at there own timing and speed but you have to make sure to turn off two Settings if you use it
Synchronize the same cards uncheck or off and don't use extend over clocking limits, i found turning off those two setting in afterburner stops all my crashes and i can set all my cards separate from the other ones on the same RIg aka mixing cards .

That software is part of Claymmore look in the claymore miner folder it's called Remote manager .

Guys,

using the Ethman do you really need to specify each miner by IP or can it just can the network and show the miner?
i don't see such option to scan the network (is way easier by more rigss.)

SO far no other way i see of doing it no scan button yet .

Use Awesome miner.....Its awesome.

https://puu.sh/sHs8b/94074a346d.png