puwaha
|
|
January 20, 2018, 11:41:39 PM |
|
Interesting... I made an order for one of these plug as well to try out the concept you outlined above. The only issue I read with this approach is that another source tells me that IFTTT takes an hour to propagate the signal to the plug, which is kinda slow (although better than nothing I suppose).
So was this not the case for you? How long does it take for the plug to "react"? Within seconds for me. When I set it up in the first pass... I used the Wemo off/on applet with no waits in AM and I would watch the Wemo smart plug go off and on over and over because the rig is not going to respond to pings immediately. I currently use TP-Link's smart plugs (HS110) for my rigs and it too can measure the power consumption and it is very reliable, but I couldn't find any ways to use IFTTT to reboot the rig when the overall power consumption dips below certain level. It simply doesn't exist.
You could potentially write your own applet, but that may be more effort than required. I think if you use AM's triggers on dead device, offline, or no accepted in X minutes it would do essentially the same thing. If you wanted to get really fancy, there is an applet in IFTTT for the Wemo insight to track switch usage in a Google spreadsheet. Then setup applets to monitor that spreadsheet and take action.
|
|
|
|
puwaha
|
|
January 20, 2018, 11:46:28 PM |
|
doesnt let u add miners with diff ports wtf....
192.168.1.129:1337 is ip and doesnt work... i change api to 3333 and it works... completly ignores port
the fuck is this shit?
I'm assuming you are trying to setup mining software that doesn't come out of the box with AM? What software is it? Did you set it up as Managed Software in AM so that AM knows how to interface with it?
|
|
|
|
wtfonly16
|
|
January 21, 2018, 12:24:12 AM |
|
doesnt let u add miners with diff ports wtf....
192.168.1.129:1337 is ip and doesnt work... i change api to 3333 and it works... completly ignores port
the fuck is this shit?
I'm assuming you are trying to setup mining software that doesn't come out of the box with AM? What software is it? Did you set it up as Managed Software in AM so that AM knows how to interface with it? its claymore eth miner..... because im using diff remote management port thats not the default 3333, awesome miner doesnt detect it. i can pull api from it using ethman just fine....
|
ye i aint bares
|
|
|
puwaha
|
|
January 21, 2018, 01:36:56 AM |
|
doesnt let u add miners with diff ports wtf....
192.168.1.129:1337 is ip and doesnt work... i change api to 3333 and it works... completly ignores port
the fuck is this shit?
I'm assuming you are trying to setup mining software that doesn't come out of the box with AM? What software is it? Did you set it up as Managed Software in AM so that AM knows how to interface with it? its claymore eth miner..... because im using diff remote management port thats not the default 3333, awesome miner doesnt detect it. i can pull api from it using ethman just fine.... Is it a different version than the one that came out of the box with AM? If it's the same one, then you don't need to specify an API port, AM already knows how to do it. It will be added automatically to the command line when it's issued to your rig. If it's a different version, then you should tell AM about it as a new Managed Software entry. Then in the entry, you tell AM that it's Claymore dual miner compatible, and it knows then what command line entry to add it's own API statement.
|
|
|
|
trolling
Newbie
Offline
Activity: 2
Merit: 0
|
|
January 21, 2018, 02:00:28 AM |
|
Hello, Running v4.3.3. Menu tab indicates a new version available to download, but the update crashes. Log file suggests failure to download required files from website. Any ideas? /20/2018 7:43:19 PM.208 [001] Updating wallet statistics 1/20/2018 7:43:19 PM.401 [022] Checking for updates: Release URL: http://www.awesomeminer.com/download/setup/ReleaseInfo.xml, Dev URL: http://www.awesomeminer.com/download/setupdev/ReleaseInfo.xml 1/20/2018 7:43:19 PM.765 [022] Current Version: 4.3.3 1/20/2018 7:43:19 PM.765 [022] New Version: 4.3.2.0 1/20/2018 7:43:19 PM.765 [022] Requires Version: 0.1.4.0 1/20/2018 7:43:19 PM.930 [022] Current Version: 4.3.3 1/20/2018 7:43:19 PM.930 [022] New Version: 4.3.4.0 1/20/2018 7:43:19 PM.930 [022] Requires Version: 0.1.4.0 1/20/2018 7:43:19 PM.930 [022] Development version update available: 4.3.4.0 1/20/2018 7:43:19 PM.930 [022] Check for updates, dev: True 1/20/2018 7:43:28 PM.178 [027] [E]Failed to download string from: https://cloud.awesomeminer.com/command/pull?userid=dGltLnJvbGxpbmdAZ21haWwuY29t&code=MDMzMTExMTkyMDg3MjM3MDg5MjA1MjMzMjA2MTk1MjA5MTE3MTEwMTUxMjAwMTI5MjIzMDY0MTYxMjM1MjE3MDg1MDEyMTYwMDgxMjM1MTgzMTUxMDMyMTAyMTQ0MjM1&systemid=1 System.Net.WebException: The remote server returned an error: (400) Bad Request. 1/20/2018 7:43:38 PM.583 [010] [E]Failed to download string from: https://cloud.awesomeminer.com/command/pull?userid=dGltLnJvbGxpbmdAZ21haWwuY29t&code=MDMzMTExMTkyMDg3MjM3MDg5MjA1MjMzMjA2MTk1MjA5MTE3MTEwMTUxMjAwMTI5MjIzMDY0MTYxMjM1MjE3MDg1MDEyMTYwMDgxMjM1MTgzMTUxMDMyMTAyMTQ0MjM1&systemid=1 System.Net.WebException: The remote server returned an error: (400) Bad Request. 1/20/2018 7:43:44 PM.801 [001] Log of miner status[ManagedMiner#2 - pb2.gtx1080TI_1] Type: Managed, EngineType: DstmMiner, EngineSubType: Disabled, UseWorkerSuffix: False, WorkerSuffix: , ManagedProfitMiner: True Algorithm: Equihash, LastStatusUpdate: 1/20/2018 7:43:44 PM, Enabled: True, InterfaceDisconnectedTimeUtc: 12/31/9999 11:59:59 PM State: Executing, ApiState: Connected, PendingCommand: False, MarkedForRemoval: False IsProfitMiner: True, IsManualStop: False, Autostart: True, Engine Type: DstmMiner, Auto Download: True, EnginePath: , Subtype: Disabled, CustomExecutable:
1/20/2018 7:45:33 PM.344 [024] [E]Failed to download string from: https://cloud.awesomeminer.com/command/pull?userid=dGltLnJvbGxpbmdAZ21haWwuY29t&code=MDMzMTExMTkyMDg3MjM3MDg5MjA1MjMzMjA2MTk1MjA5MTE3MTEwMTUxMjAwMTI5MjIzMDY0MTYxMjM1MjE3MDg1MDEyMTYwMDgxMjM1MTgzMTUxMDMyMTAyMTQ0MjM1&systemid=1 System.Net.WebException: The remote server returned an error: (400) Bad Request. 1/20/2018 7:46:35 PM.820 [025] [E]Failed to download string from: https://cloud.awesomeminer.com/command/pull?userid=dGltLnJvbGxpbmdAZ21haWwuY29t&code=MDMzMTExMTkyMDg3MjM3MDg5MjA1MjMzMjA2MTk1MjA5MTE3MTEwMTUxMjAwMTI5MjIzMDY0MTYxMjM1MjE3MDg1MDEyMTYwMDgxMjM1MTgzMTUxMDMyMTAyMTQ0MjM1&systemid=1 System.Net.WebException: The remote server returned an error: (400) Bad Request. 1/20/2018 7:47:27 PM.931 [028] [E]Failed to download string from: https://cloud.awesomeminer.com/command/pull?userid=dGltLnJvbGxpbmdAZ21haWwuY29t&code=MDMzMTExMTkyMDg3MjM3MDg5MjA1MjMzMjA2MTk1MjA5MTE3MTEwMTUxMjAwMTI5MjIzMDY0MTYxMjM1MjE3MDg1MDEyMTYwMDgxMjM1MTgzMTUxMDMyMTAyMTQ0MjM1&systemid=1 System.Net.WebException: The remote server returned an error: (400) Bad Request.
|
|
|
|
|
yhbae
Newbie
Offline
Activity: 119
Merit: 0
|
|
January 21, 2018, 03:46:33 AM |
|
Interesting... I made an order for one of these plug as well to try out the concept you outlined above. The only issue I read with this approach is that another source tells me that IFTTT takes an hour to propagate the signal to the plug, which is kinda slow (although better than nothing I suppose).
So was this not the case for you? How long does it take for the plug to "react"? Within seconds for me. When I set it up in the first pass... I used the Wemo off/on applet with no waits in AM and I would watch the Wemo smart plug go off and on over and over because the rig is not going to respond to pings immediately. Cool... I currently use TP-Link's smart plugs (HS110) for my rigs and it too can measure the power consumption and it is very reliable, but I couldn't find any ways to use IFTTT to reboot the rig when the overall power consumption dips below certain level. It simply doesn't exist.
You could potentially write your own applet, but that may be more effort than required. I think if you use AM's triggers on dead device, offline, or no accepted in X minutes it would do essentially the same thing. If you wanted to get really fancy, there is an applet in IFTTT for the Wemo insight to track switch usage in a Google spreadsheet. Then setup applets to monitor that spreadsheet and take action. Hmmm, so it sounds like it is possible to write some plug-in for AM to trigger IFTTT to control these smart plugs. Perhaps I should try this on my current TP-Link plugs. I have 9 of them - hopefully this approach works!
|
|
|
|
wtfonly16
|
|
January 21, 2018, 04:33:02 AM |
|
doesnt let u add miners with diff ports wtf....
192.168.1.129:1337 is ip and doesnt work... i change api to 3333 and it works... completly ignores port
the fuck is this shit?
I'm assuming you are trying to setup mining software that doesn't come out of the box with AM? What software is it? Did you set it up as Managed Software in AM so that AM knows how to interface with it? its claymore eth miner..... because im using diff remote management port thats not the default 3333, awesome miner doesnt detect it. i can pull api from it using ethman just fine.... Is it a different version than the one that came out of the box with AM? If it's the same one, then you don't need to specify an API port, AM already knows how to do it. It will be added automatically to the command line when it's issued to your rig. If it's a different version, then you should tell AM about it as a new Managed Software entry. Then in the entry, you tell AM that it's Claymore dual miner compatible, and it knows then what command line entry to add it's own API statement. it wants me to add pools and shtt.. wtf? i just want to monitor.................
|
ye i aint bares
|
|
|
cashen
|
|
January 21, 2018, 05:00:03 AM |
|
doesnt let u add miners with diff ports wtf....
192.168.1.129:1337 is ip and doesnt work... i change api to 3333 and it works... completly ignores port
the fuck is this shit?
I'm assuming you are trying to setup mining software that doesn't come out of the box with AM? What software is it? Did you set it up as Managed Software in AM so that AM knows how to interface with it? its claymore eth miner..... because im using diff remote management port thats not the default 3333, awesome miner doesnt detect it. i can pull api from it using ethman just fine.... Is it a different version than the one that came out of the box with AM? If it's the same one, then you don't need to specify an API port, AM already knows how to do it. It will be added automatically to the command line when it's issued to your rig. If it's a different version, then you should tell AM about it as a new Managed Software entry. Then in the entry, you tell AM that it's Claymore dual miner compatible, and it knows then what command line entry to add it's own API statement. it wants me to add pools and shtt.. wtf? i just want to monitor................. Are you setting up an "external" miner? Sounds like you are setting up a managed miner.
|
|
|
|
eminer001
Newbie
Offline
Activity: 140
Merit: 0
|
|
January 21, 2018, 06:39:46 AM |
|
Is there any way to set an overclock profile per gpu and per algo?
so for example MINER01 -> GPU0 -> will have different overclock settings based on the different algos THEN MINER01 -> GPU1 -> will have different overclock settings based on the different algos and so on
is it possible?
I also agree that one algo needs memory OC and another algo needs base clock oc. Without this functionality we are not maximizing the profits, and mining is all about maximizing profits by having all coins and algos and best settings for each.
|
|
|
|
eminer001
Newbie
Offline
Activity: 140
Merit: 0
|
|
January 21, 2018, 06:43:17 AM |
|
Please add Intense (ITNS) and Masari (MSR). Small, but profitable, CryptoNight coins.
Yes, we have a very small number of coins in AM , a lot of profitable ones are missing.
|
|
|
|
eminer001
Newbie
Offline
Activity: 140
Merit: 0
|
|
January 21, 2018, 06:46:48 AM |
|
I know you're working on a lot of these. Keep up the great work!! 1 Suggestion. 1. Move the "Current" vs "24 hour average" to profit page 2. Have it be current or Custom, where custom is average in X mins. This will allow the user to choose 5 minutes, 1440 for 1 day etc. Anyone like or dislike this suggestion please provide constructive feedback. I also believe that custom minutes is the best to have. 24 hours is too much, but something like 10 minutes or 1 hour would be a lot more helpful.
|
|
|
|
ruplikminer
Jr. Member
Offline
Activity: 504
Merit: 3
|
|
January 21, 2018, 12:23:11 PM |
|
Is there any way to set an overclock profile per gpu and per algo?
so for example MINER01 -> GPU0 -> will have different overclock settings based on the different algos THEN MINER01 -> GPU1 -> will have different overclock settings based on the different algos and so on
is it possible?
I also agree that one algo needs memory OC and another algo needs base clock oc. Without this functionality we are not maximizing the profits, and mining is all about maximizing profits by having all coins and algos and best settings for each. Exactly. That's what I really need. Some algos runs better on base clock some others on memory. This would be a very useful feature! Patrick already told me that it will be added shortly!
|
|
|
|
thucar
Newbie
Offline
Activity: 8
Merit: 0
|
|
January 21, 2018, 01:44:10 PM Last edit: January 21, 2018, 03:24:36 PM by thucar |
|
Well, my things are going from bad to worse. This is what my AM dashboard is showing right now. Both miners are spending more time idling than working. https://i.snag.gy/M4wiKn.jpgEDIT: Just upgraded to the latest Dev version - both, the monitoring PC as well as both remote clients on the miners. No change, still restarting both miners at the exact same time every 15-20 minutes.
|
|
|
|
btesla
Newbie
Offline
Activity: 22
Merit: 0
|
|
January 21, 2018, 03:31:10 PM |
|
Hi there,
Is it supports Magi (XMG) Coin (it's CPU mining)?!
Thank you!
|
|
|
|
nemzy
Newbie
Offline
Activity: 13
Merit: 0
|
|
January 21, 2018, 05:28:04 PM |
|
ppl did some one manage to make nanopool in awesome miner? there is a worker name and pass with e-mail can some make a screen please? or just give some examp. and same story with balance ... And how u can add xmr cast vega just like external miner, no manage one ?!? claymore has default port 3333 and i'm not sure about xmr cast vega. may be i need to insert some in bat file?
|
|
|
|
Chapster
Member
Offline
Activity: 75
Merit: 10
|
|
January 21, 2018, 05:47:04 PM |
|
So far, my numbers are not far off from yours. For MPH, is that number based on BTC auto-exchange or are you mining a specific coin and receive only that coin?
Thanks.
For MPH I used BTC auto-exchange. At the end (and after allowing several days for the results to settle), MPH seems to be the one which is the most reliable in terms of the estimated profit they report.
|
|
|
|
WCSSTORE
Newbie
Offline
Activity: 12
Merit: 0
|
|
January 21, 2018, 05:59:22 PM |
|
Anyone else having a hard time adding yiimp.eu (xvg) to awesome miner?
I used stratum+tcp://yiimp.eu:3737 (and 3777) for the coin I used "unspecified x17" and then I put in my XVG wallet But when starting mining it keeps saying "retry after 30 sec"
Also If I use the ccminer without awesome miner it works.
|
|
|
|
Emkoo
Jr. Member
Offline
Activity: 103
Merit: 1
|
|
January 21, 2018, 07:00:18 PM |
|
I might have stupid question but I just started with mining 1. How do I setup my Awesome miner to show me daily/monthly profit in USD? 2. How do I setup my Awesome miner to show me my real profit (daily profit-elec.cost)? 3. How do I setup my Awesome miner soft to show me what is my balance in my coinbase wallet? Using Antminer S9, conected to slush pool. I'm sure that those answers are somwhere in this thread but it has over 200 pages and I can't find it. Thanks everyone!
|
|
|
|
eminer001
Newbie
Offline
Activity: 140
Merit: 0
|
|
January 21, 2018, 07:12:06 PM |
|
Anyone else having a hard time adding yiimp.eu (xvg) to awesome miner?
I used stratum+tcp://yiimp.eu:3737 (and 3777) for the coin I used "unspecified x17" and then I put in my XVG wallet But when starting mining it keeps saying "retry after 30 sec"
Also If I use the ccminer without awesome miner it works.
I also think that more pools and more coins and algos should be added to AM. There are so many users of AM that are loosing money because AM is lacking more pools and lacking especially very high profit algos like phi that is the number one mined algo on almost all pools for days and the users that bought and paid for AM are loosing money for days because AM is lacking PHI support.check that more than 50% of the pool is on PHI now: http://yiimp.eu/site/mining or https://www.ahashpool.com/ and they make more money than the others (on what side are you ? ) If AM will have more pools and missing algos, users that paid won't have troubles making more money, right ?
|
|
|
|
|