I tiried all those ports at first and now end up using it at my boards work well or seem to like that setting best, no board is doing 12 MN while the rest do 32 MH if I use that differently setting as part of my set up . I tested it a lot and it all most worthless to over clock them with the new firmware beyond tried a few times at max 352 it worked for while then shut down and i had lots of cool air blowing on the boards, it gets some really strange high HW errors then say some thing about floating point limit reached in BFG then stops mining till it's shuts off or reset with the clocks at 320, so i leave it there and have no issue at all . and the firmware acttly works another way or has so far for me if i have the fans off it will shut down if it gets to hot after 12 mins and has so far every time @ 12 mins, i tested it . so with the update it seems it can't over heat and burn out the boards Jat did some nice work fixing the manufacturer mistakes . And i have problem with install.sh and autostart,sh .. . are you using the MAT controller if so that why . let me find that post how to fix it . you have to change stuff on that controller if you replaced it with the new BFG or other GUI after you flashed the boards according to what Jat said on the old lite coin forums all that controller is a watered version of a raspberry PI once you over write the old software you have to change some paths and other stuff on that controller ,I'm using my own controller with custom plugs to a USB 3.0 self powered Hub plugged into a Cubieboard PI running either minera or just BFG with Ubuntu 16.04.1 . hey can you post Screens shots of that fan set up, i might try it to cut down even more on noise and run them cooler . here's my post about how to use it with a custom PI or your own controller . https://bitcointalk.org/index.php?topic=1468120.0
|
|
|
update Operation Sysytem : Win 10 64bit 4 PC's Wallet :Poloniex T address Miner : genoil-zec .4.1 for my 470 and .4.2 for my 370 and 280 VGA Card(s): rig 1, XFX RX 470 4 GB / SAPPHIRE REF RX 470 4GB /SAPPHIRE Nitro rx470 4g rig 2, r7 370 4gb rig 3, r7 370 4gb rig 4, R9280 3gb VGA driver : Crimson Edition 16.10.3 Hotfix speed :rig 1 zec-sa#0: 32.9S/s/zec-sa#1: 30.1S/s/ zec-sa#2: 35.5S/s speed : rig 2 zec-sa#0: 26.7S/s speed :rig 3 zec-sa#0: 27.9S/s speed :rig 4 zec-sa#0: 31.5S Pool: us1-zcash.flypool.org:3333 Bat or start file settings : rig 1 genoil.exe -c us1-zcash.flypool.org:3333 -u zec t address.rigx -p z rig 2 genoil.exe -c us1-zcash.flypool.org:3333 -u zec t address.rigx -p z rig 3 genoil.exe -c us1-zcash.flypool.org:3333 -u zec t address.rigx -p z rig 4 genoil.exe -c us1-zcash.flypool.org:3333 -u zec t address.rigx -p z CPU (if you mining with cpu): not using IF you don't know what silentarmy kernels, is or does . https://www.youtube.com/watch?v=28wGCQT6lfI
|
|
|
I can't belive they have testing Zcahs for 15 days and they have not tested transactions ? or windows miners, windows off line wallet or well I won't go there .
|
|
|
Can anyone share how to control GPU fan speeds in ubuntu using the latest GPUPRO drivers? Finally got it running, but now the cards overheat and crash. Turns out the problem was using the live persistent USB after all. Once installed normally the drivers installed easy peezy.
PS I tried the previously posted method somewhere around page 54, didn't work.
I m glad it worked out for you. Wish I could get there. You mind me asking which version of ubuntu are you using. I've been stuck at the login loop after installing amd gpupro drivers. When I did get it to work. I encounter the error no opencl devices found. blah blah blah. TIA I used Ubuntu 16.04.1 LTS and followed the directions on AMD's site. THere is more to it then what info they give you may need some other downloads before you even try like the SDK installed with includes set before you do and may be even need this sudo apt-get install lib32z1 lib32ncurses5 lib32bz2-1.0 lib32stdc++6 and redo your it took me a few hours the other day getting them installed but i did it after i did I reformatted the Hard driver went back to windows just want to see if i could , you may need to change line 67 in the amdgpupro install file to this echo ${dir}${etc}${dir}${sourceparts}/amdgpu-pro.list as for seeing fan speeds and temps and controlling them it is possible but i couldn't find it, it has some thing to do with how the sdk is installed and the includes are set up right . and the other reason i went back to windows couldn't find out how to , is your card supported by that driver yet , i found out not all R7 series cards are so you have to use Ubuntu 15 or lower . and that can be another mess but fun at first to learn .
|
|
|
I've had 560 sols on this pool for 9 hours and so far have 0.006 ZEC... If I had used coinmine.PL I would have had ~0.18 zec by now.,...
Conclusion: THIS POOL IS STEALING OUR HASH!!!!!!!!!
Address please Sone info, when you start transaction, you can't check your Z-Address balance (it becomes invalid) and queue more than one transaction to Z/T address. Therefore, you can't queue a batch transaction from one Z-Address (or one zcash node?). I reduced payout to 1min, since now pool payouts on maximum speed possible for zcash node (or single Z-address, can't really say). nasty bug atm https://github.com/zcash/zcash/issues/1705
|
|
|
I think you should enable payments only for t address for now, so at least the majority of the miners can get paid and it is not taking 30min per payout.
That's what http://zcash.flypool.org is doing I'm only using a T address and kind glad now there is no windows off line wallet yet .
|
|
|
because i can't put all my GPUs on one pool with the CPUs . i was force to mine on Nice hash till they fix that crash in this miner https://github.com/Genoil/ZECMiner/tree/master/releases for AMD cards on windows once it's fixed that miner can mine on any pool with windows or you can run a Linux box and use this one https://bitcointalk.org/index.php?topic=1661160.0 i think it works on any pool . my sol is at 100 or a little less with 3 470 two r7 370 and one 280 and using two 8 core cpus at 6 cores . i have two 4 core CPU i need to ad better cooling to or id be using them at 2 or 3 cores , cheap cooling on them . @ Searing i should have listen to you to start with at least at nicehash I can put all my CPUs and GPUs on one pool with one miner and not worry to much about bad pay outs or is the site adding it up right , i believe zcash.flypool.org would but no working miners like nicehash has so it's nice hash for at least the next three or four days,let them sell it for me and credit my btc address , I'm not even gonna use nicehashes pool that pays out with ZEC , if i want a peace of the PIE . [ b]WTH is wrong hahah [/b]I am running nicehash with 1 x 7950 4 x 280x
Im only getting 30 sol is there anything I can do to tweak or trouble shoot itmy code is as follows nheqminer_zcash -l usa -u t2UNzUUx8mWBCRYPRezvA363EYXyEpHokyi -t 0 -od 0 1 2 3 4 You should get at least 50sols/s any ideas? Turn a few cores on, i did a -h to see what helps or use overclocking software but that doesn't seem to do to much but does help some, ID say turn on some cores if your CPU can handle it and has good cooling , MY AMD 8 core is set to use 6 cores with a R7 370 im doing close to 20 sol with 6 cores on, i was doing 9 to 10 sols with the GPU by it self. . even the APU's cpu coers can jack it up a little, i found out but i have a really bad cooler on it so using two cores makes it over heat to much but did give that GPU a nice boost, i don't mean the APU video part . if I read and understand how it works,I'm doing 19 sols Speed [300 sec]: 10.6867 I/s, 19.91 Sols/s
|
|
|
my three RX 470 at best only do 16 sol each not the 20 something in the title any DOC on how to tweak them for your software miner and they have modded bios, i would think that should make them run better even here . mining ETH they get a good 27 MH each steady.
|
|
|
Ive all ready stopped mining here i want to mine here http://zcash.flypool.org/ but the software miner they link is shit right now. is it only Win 10 it crashes on if so i can install 7 or 8.1 ? if windows 10 is the problem which might be it.
|
|
|
mining on two sites atm one with CPU's http://zcash.flypool.org/ I can't GPU mine here yet the AMD miner they link for windows crashes with in second and i can't find another windows based software miner that works on that site and Bash on Ubuntu on Windows is a bitch to set up and i get bored tiring to get the AMD drivers to install and not gonna box all my PC with Ubuntu. I like windows to much . the other site GPU mining http://coinsforall.io mining here only because there software miner only works on there site, i tried with zcash.flypool in the conf, it won't connect . gonna check out super nova next don't care much for nicehash . I had exactly the same experience on zcash.flypool.org. miner crashes within a second. What a bummer. will try suprnova once they have t-addresses working (right now crashes on suprnova as well) what platform is AMD (1?) in that software for AMD no idea yet i wish it worked I'm gonna like zcash.flypool a lot probable as mush as i like ethermine.org one of there sister sites.
|
|
|
Mining ZCash the central processor i7 will be possible? There is such instruction?
you can here under windows use the software miner they link , I'm using it with two 8 core and two four cores,one is a Intel 1155 socket CPU . the GPU software they link crashes my GPU's with in second, i had to use software for GPU mining form another site that only works on that site for now. http://zcash.flypool.org I'm CPU mining there as I type this.
|
|
|
mining on two sites atm one with CPU's http://zcash.flypool.org/ I can't GPU mine here yet the AMD miner they link for windows crashes with in second and i can't find another windows based software miner that works on that site and Bash on Ubuntu on Windows is a bitch to set up and i get bored tiring to get the AMD drivers to install and not gonna box all my PC with Ubuntu. I like windows to much . the other site GPU mining http://coinsforall.io mining here only because there software miner only works on there site, i tried with zcash.flypool in the conf, it won't connect . gonna check out super nova next don't care much for nicehash .
|
|
|
I'd say here http://zcash.flypool.org/ but I'm only able to CPU mine atm because the GPU miner they link crashes with in second of using and i Can't find another windows based Zcash miner that works with that site and this one is looking like it gonna be the best site. or try here http://coinsforall.iothey have a miner that only works on that site or would only work there for me . Both seem to be very stable . it depend more right now on the software miner and OS your using then the pool . Hope that helps thanks top
|
|
|
link to sony's elpida nitro 470 4gb is all down.
can someone please share it here ?
much TIA.
link is in this video only place to get it atm unless some one else shares it. i found it looking for ways to tweak sgminer-gm more which ofc I won't find right now , i did find all kinds of other interesting stuff . https://www.youtube.com/watch?v=ajQQQ2JQicE
|
|
|
https://litecointalk.org/index.php?topic=27370.0 I run my MAT/Alcheminer a few days a week and eth mine everyday , I'm what you would call a hobby miner , and it is a hobby for me with a kind of reward . i flashed my boards using that guide, if you flashed your boards and need to fix a bricked one ask jstefanop he may be able to help you, if you want to flash the boards with that firmware , bfg is free the firmware it self may not be ask jstefanop he may give it to you or ask for a few bucks for it, he wrote it.
|
|
|
I'm happy with mine doing 27 MH from time to time i like to mess around at first but usually after i find the Sweet spot i stay with it. btw the 28 Mh test lasted two days then it crashed so i went back to 27 MH which is what the sweet spot seems to be .
thanks toptek
|
|
|
Man I love awesome Miner and Minera will keeping using both and keep paying for both, If i have to as long as i keep mining .
I noticed some thing it seems every time you try to add support for the latest version of Claymore miners without using the upload tool you gave us which is a great help , with in hours he posts a new version, 7.3 for windows is out now . it seems that way I'm sure it's not and me being the update fool , I am will try it and if it works ok ill keep using it etc weather i need to or not .
|
|
|
So if the efficiency is no better than a Titan -- then -- is this a SCAM?
Why would someone overpay to buy these units? I'm lost here.
It seems that it is basically 2.5x as efficient as the 100Mh/s A2 units (which are selling for about $650 with PSU).
Sadly, no its not a scam. Miners will be flocking to these, just like every stupid hardware release ... no matter the price and no matter the efficiency. Its an addiction. Ill probably be the only one not purchasing any. Nope, not the only one... Unless the price drops. A lot. same after reading everything here Id rather by a few A2's and try to get a titan, the titan has more hash power if all the dies work ,what's the point . other then a fool and his money no offense intended to anyone by that commit .
|
|
|
|