Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[PKBO]

Hi guys, currently iam running EWBF CUDA miner, but i would like to try EHT+SIA.
Have 4 diferent rigs with nV 980/980Ti/1070/1080/T-X/T-XP.

some rigs gives me 30 mhs first card and 3mhs for others, another rig gives me 3mh/s for each, so there is some issue.

Is there any of you, who will post working multiple nV config ?

Thx guys !

[notbatman]

That screen cap is too fuzzy to read but vydelek has two -epool entries, could that be the problem?

[dt8666]

Dual mining question.
When i do Eth + Drc, i get :
29.5mhs on ETH
and
870 on Dcr

But dual on ETH + Sia, i get
23 mhs on ETH
And
500+ on Sia.

Question.
1. Is this normal?
2. Can i set to higher ETH?

[preda]

Dual mining question.
When i do Eth + Drc, i get :
29.5mhs on ETH
and
870 on Dcr

But dual on ETH + Sia, i get
23 mhs on ETH
And
500+ on Sia.

Question.
1. Is this normal?
2. Can i set to higher ETH?

Yes, put -dcri 30 for start ... more is this number more will be the second coin and decrease the eth megahash...

Try with 30-40 or 50 see when you lose not much mh and you will gain more second coin

[SealTx]

Theory Question:

Why Decred, Siacoin, Lbry, and Pascal?

I am guessing that Claymore has a large client that wants to mine those coins, but are there other requirements for a coin's hashing algo or miner so that it can be dual mined (easily) by Claymore?

[Crypto.Slack3r]

Has anyone else's hashrate essentially halved using RX480?  I was never getting world-class hashrates (~23MH/s) but now it's down around 13MH/s for the two RX 480s that I'm testing. [ETH/ETC mining]  For reference,  I'm dual-mining SiaCoin and that halved as well from 7xx to 3xx.

Disclaimer:  I did install an RX 570 into the system to test,  didn't get the results that I was after so disconnected the card and uninstalled the AMD drivers completely before reinstalling 16.9.2. 

Suggestions?

[preda]

Has anyone else's hashrate essentially halved using RX480?  I was never getting world-class hashrates (~23MH/s) but now it's down around 13MH/s for the two RX 480s that I'm testing. [ETH/ETC mining]  For reference,  I'm dual-mining SiaCoin and that halved as well from 7xx to 3xx.

Disclaimer:  I did install an RX 570 into the system to test,  didn't get the results that I was after so disconnected the card and uninstalled the AMD drivers completely before reinstalling 16.9.2. 

Suggestions?

Idk mine rx 480 are mining as always no problem with speed

[abstmain]

Nice! Ty!

[miner582]

I am dual mining under linux without any problem, however I faced a couple of time a strange behavior. When my decred pool is down or a connectivity issue is present the entire miner stop mining, my rig is up and accessible via ssh but the miner stop hashing on both coins, this is a "by design" behavior or is there any option I missed that allow the to keep mining ETH and do nothing with decred meantime the connectivity issue persist?

Thanks for your inputs.

[Cryptonesia]

It's been several months I've been mining using Claymore (with only 1 GPU) and currently my shares are getting lower and lower due to the difficulties increase. But for the last week, my shares on dwarfpool are waaaay much lower than what Claymore shows me. As you can see on this picture attached, I should have to got apprx. 280 shares on my last 7 hours mining progress but what my pool shows is only 124 shares submited. I tried to move to another pool and it keep happens to me. I actually have 3 GPU (RX470 & RX570) and I tried each card and result are still the same. What should I do? Is it stale shares? Anyone can help me?

http://imgur.com/fVvTkUk
http://imgur.com/LfskcEs

[Vaas]

It's been several months I've been mining using Claymore (with only 1 GPU) and currently my shares are getting lower and lower due to the difficulties increase. But for the last week, my shares on dwarfpool are waaaay much lower than what Claymore shows me. As you can see on this picture attached, I should have to got apprx. 280 shares on my last 7 hours mining progress but what my pool shows is only 124 shares submited. I tried to move to another pool and it keep happens to me. I actually have 3 GPU (RX470 & RX570) and I tried each card and result are still the same. What should I do? Is it stale shares? Anyone can help me?

http://imgur.com/fVvTkUk
http://imgur.com/LfskcEs

same thing here

[tbly13]

Just looking for some opinions here:

I fired up 2 AMD 7950's Dual-Mining ETH and Sia Last night. Been sort of tweaking the settings and Overclock over the past 12H but wanted to see if I am getting proper results for my settings:


BAT:

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool us1.ethpool.org:3333 -ewal 0x9C242ad2B0cF40f58e01C7b8c3b79f83F792bD18  -dpool "http://siamining.com:9980/miner/header?
address=be71aa6e9ca5e046fde5c6fedc9a295bbf631acd300b57d7e20559bd53850f3d86442bc20ee8&worker=Work1" -dcoin sia

CLOCKS:

2 AMD 7950: 1050/1500

Haven't done much OC tweaking/testing with these - Just raised memory clocks mostly to see a little MH boost


MH:

Client Side - ETH: ~25MH (Accepting around 20-25 Valid Shares/hour on ethpool). Sia: ~385MH (75-80k Valid Shares/Hr on SiaMining)

Pool Side Screenshots- ETH: https://www.screencast.com/t/ySMnJBLuwE , SIA: https://www.screencast.com/t/qZyq9wv9


Wondering if these results seem normal, or if I could be doing something better?


Thanks!

[z0n0]

What's wrong with my .bat line?

Code:

EthDcrMiner64.exe -epool eth.coinmine.pl:4000 -ewal z0n0.1 -epsw x -esm 0 -dpool sia.suprnova.cc:7777 -dwal z0n0.1 -dpsw x -dcoin sia -allpools 1

This is what I get:

Code:

GPU0 t=47C fan=48%
ETH: 06/06/17-20:21:24 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.570 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.570 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:31 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 25.953 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 25.953 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed to connect, retry in 20 sec...
ETH: 06/06/17-20:21:34 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.654 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.654 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:49 - New job from eth.coinmine.pl:4000
GPU0 t=50C fan=48%
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
ETH - Total Speed: 26.581 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:01
ETH: GPU0 26.581 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed

[joosep]

What's wrong with my .bat line?

Code:

EthDcrMiner64.exe -epool eth.coinmine.pl:4000 -ewal z0n0.1 -epsw x -esm 0 -dpool sia.suprnova.cc:7777 -dwal z0n0.1 -dpsw x -dcoin sia -allpools 1

This is what I get:

Code:

GPU0 t=47C fan=48%
ETH: 06/06/17-20:21:24 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.570 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.570 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:31 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 25.953 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 25.953 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed to connect, retry in 20 sec...
ETH: 06/06/17-20:21:34 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.654 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.654 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:49 - New job from eth.coinmine.pl:4000
GPU0 t=50C fan=48%
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
ETH - Total Speed: 26.581 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:01
ETH: GPU0 26.581 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed

Try: -esm 3

[preda]

What's wrong with my .bat line?

Code:

EthDcrMiner64.exe -epool eth.coinmine.pl:4000 -ewal z0n0.1 -epsw x -esm 0 -dpool sia.suprnova.cc:7777 -dwal z0n0.1 -dpsw x -dcoin sia -allpools 1

This is what I get:

Code:

GPU0 t=47C fan=48%
ETH: 06/06/17-20:21:24 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.570 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.570 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:31 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 25.953 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 25.953 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed to connect, retry in 20 sec...
ETH: 06/06/17-20:21:34 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.654 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.654 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:49 - New job from eth.coinmine.pl:4000
GPU0 t=50C fan=48%
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
ETH - Total Speed: 26.581 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:01
ETH: GPU0 26.581 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed

Try: -esm 3

What is -esm 3?

[z0n0]

What's wrong with my .bat line?

Code:

EthDcrMiner64.exe -epool eth.coinmine.pl:4000 -ewal z0n0.1 -epsw x -esm 0 -dpool sia.suprnova.cc:7777 -dwal z0n0.1 -dpsw x -dcoin sia -allpools 1

This is what I get:

Code:

GPU0 t=47C fan=48%
ETH: 06/06/17-20:21:24 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.570 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.570 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:31 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 25.953 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 25.953 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed to connect, retry in 20 sec...
ETH: 06/06/17-20:21:34 - New job from eth.coinmine.pl:4000
ETH - Total Speed: 26.654 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 26.654 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
ETH: 06/06/17-20:21:49 - New job from eth.coinmine.pl:4000
GPU0 t=50C fan=48%
 SC: Stratum - connecting to 'sia.suprnova.cc' <46.105.118.15> port 7777
ETH - Total Speed: 26.581 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:01
ETH: GPU0 26.581 Mh/s
 SC - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 SC: GPU0 0.000 Mh/s
 SC: Stratum - Cannot connect to sia.suprnova.cc:7777
 SC: Stratum - Failed

Try: -esm 3

Same
Is suprnova maybe down currently?

[joosep]

What is -esm 3?

-esm   Ethereum Stratum mode. 0 - eth-proxy mode (for example, dwarpool.com), 1 - qtminer mode (for example, ethpool.org),
   2 - miner-proxy mode (for example, coinotron.com), 3 - nicehash mode. 0 is default.

[Emoclaw]

Do not use Crossfire for mining, disable it.
Set the core clock to 1200MHz or lower (just enough to not affect your hashrate by a significant amount), as well as the voltage, and the memory clock as high as you can without getting any GPU Memory errors in HWinfo.
Look into BIOS modding as well, only through that will you have a shot at getting 30MH/s.

I did some bios modding and tuning is msiAB last day. HWinfo was running and showed 0 errors, but I saw glitches on the screen, and after a few mins my system froze. Tried multiple times with multiple variations but no errors in HWinfo, just glitches and crashes.
I did find the almost optimal settings, but HWinfo did not help me.
I think I missed something. Can you help me pls?

What exactly did you tune? What's your memory vendor?
Try copying the 1750MHz strap to 2000MHz if you have Micron or Samsung.

[Claymore]

@Claymore,
I've now been able to replicate the EthMan bug with as few as 3 miner entries, tested on both Win 7 x64 and Win 10 machines.
Freshly generated config file with three local IPs added, only one of which has a running miner. (ETH 9.4)
Leave open for 5-10min, crashes every time. (all miners shown as red/offline)

Fixed too, I will release new version of the miner and EthMan within 24 hours.

[XManiac]

I dont understand, ETH difficulty groves up 2 times?