BitJunkie556
|
|
December 15, 2016, 04:42:26 AM |
|
hopely this will help you, if all your hardware don't have a problem from PSU,cable, and riser, instal the lastest driver ( in my experience for multiple GPU wait until finish all instal the driver), restart, and run MAB set default for all setting accept fan speed as you needed at your temp room, and then run claymore v.9.1. If still get hang try setting your intensity one by one from 5, 6,7 or 8.
I did all those steps, but no use. And yes, I have latest catalyst 16.11.2, I even low intensity to 4. May I ask about your hardware, like CPU, Mobo, PSU, RAM, and OS? I read from above that it need 80 bronze cert PSU, im not sure if that's the problem, or from my OS. Just my .02, but I believe the default intensity is 4. I could be wrong, but I have set -i 4 and my hashrate is same as default without setting intensity. Try backing it down to 1 or 2, then try to get up to 3 and see what runs stable. Also, suppose you have a 1000 watt bronze psu and 4 RX 480's running. 150 watts per card. They actually use much less, but that would be 600 watts. Then your cpu is maybe going to be pulling 100 max, and that's if it ever gets to any kind of load... You'd have lots of headroom. Unless you're trying to run a 6 card rig on 1000 watt psu lol.
|
|
|
|
|
|
|
|
You get merit points when someone likes your post enough to give you some. And for every 2 merit points you receive, you can send 1 merit point to someone else!
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
Nthused
Legendary
Offline
Activity: 1554
Merit: 1001
|
|
December 15, 2016, 05:18:00 AM |
|
I use intensity set to -2 all the time when I do mine Equihash with my 280x's and have no invalid reds or any of that, Version 9 and 9.1 works perfectly for me although I haven't done power readings on each version yet compared to Version 8.
|
|
|
|
maxrena
Newbie
Offline
Activity: 23
Merit: 0
|
|
December 15, 2016, 05:35:49 AM |
|
hopely this will help you, if all your hardware don't have a problem from PSU,cable, and riser, instal the lastest driver ( in my experience for multiple GPU wait until finish all instal the driver), restart, and run MAB set default for all setting accept fan speed as you needed at your temp room, and then run claymore v.9.1. If still get hang try setting your intensity one by one from 5, 6,7 or 8.
I did all those steps, but no use. And yes, I have latest catalyst 16.11.2, I even low intensity to 4. May I ask about your hardware, like CPU, Mobo, PSU, RAM, and OS? I read from above that it need 80 bronze cert PSU, im not sure if that's the problem, or from my OS. Just my .02, but I believe the default intensity is 4. I could be wrong, but I have set -i 4 and my hashrate is same as default without setting intensity. Try backing it down to 1 or 2, then try to get up to 3 and see what runs stable. Also, suppose you have a 1000 watt bronze psu and 4 RX 480's running. 150 watts per card. They actually use much less, but that would be 600 watts. Then your cpu is maybe going to be pulling 100 max, and that's if it ever gets to any kind of load... You'd have lots of headroom. Unless you're trying to run a 6 card rig on 1000 watt psu lol. I have 2 x 750W PSU, each PSU runs 3 cards. I dont blame Claymore 9.0 or 9.1, I had this problem since the first time I use claymore, since 5.0. There will be 1 card always not working, will hash 0 H/s. After a certain of time, watchdog says that GPU hangs and reset. No matter how many GPU I use, there will be 1 not working. My temporary fix was keep rebooting until all GPUs working, but now that ways seems not work anymore.
|
|
|
|
imunisasi
Member
Offline
Activity: 86
Merit: 10
|
|
December 15, 2016, 05:39:56 AM |
|
gpu showing 0.00 is there something wrong with it ? but they booting normally must i reinstall video driver again ?
thank you
|
|
|
|
ivcelmik
|
|
December 15, 2016, 05:57:00 AM |
|
yep 5 hours no block this is realy bad luck for today. Never see this before They are about 10 to 11 blocks under predicted by their 5% hash. It should be a funny catch up ahead. Some people play the mountains and valleys for an extra income edge. Now is too late for me to switch flypool 18.000 Msol/s => 183 blocks per day => 7.625 blocks per hour dwarfpool 2.500 Msol/s => 25 blocks per day = 1 block per hour 7 hours without a block will not be catched up the next 24 hours ..... Try Dwarfpool and u;ll see the reward difference
|
|
|
|
bolt1909
Member
Offline
Activity: 65
Merit: 10
|
|
December 15, 2016, 07:20:27 AM Last edit: December 15, 2016, 07:41:14 AM by bolt1909 |
|
Wtf is going on with flypool...4 hours (00:47-04:45) without one (ONE = 1) shares??? http://imgur.com/a/32hBJedit: -zpool eu1-zcash.flypool.org:3333 and I checked 3 times my network connection, was ok
|
|
|
|
TR8888
|
|
December 15, 2016, 07:22:41 AM |
|
Working fine here with no dropouts, EU1.
|
|
|
|
QuintLeo
Legendary
Offline
Activity: 1498
Merit: 1030
|
|
December 15, 2016, 08:52:51 AM |
|
I use intensity set to -2 all the time when I do mine Equihash with my 280x's and have no invalid reds or any of that, Version 9 and 9.1 works perfectly for me although I haven't done power readings on each version yet compared to Version 8.
Tried a fresh download of 9.1 tonight, as I'd been having some issues trying to copy it over my network - turns out that the HD on the machine I originally downloaded it to had a bad sector in one of the .bin files that appears to have been causing some of my problems with it. Dual 280x machine went from 370 sol/s to 400 - one card I have to run at -i 4 or it gets constant rejects/invalid data errors the other is fine at -i 8 (v8 used -i 3 and 6 respectively). The fameous HD 7870 test rig went from 105ish to 130ish. Another rig with a 7870 and a 7750 went from 105/42 to 130ish/55ish The dual RX 470s though were already on 9.1 so no change. 8-P v9 on the other hand STILL didn't work on the 2 machines I tried THAT on tonight - but 9.1 DID so forget v9.0 I DID see some connection issue with flypool on the usa node tonight, but nothing long lasting. Might have been a glitch/outage on the backbone somewhere.
|
I'm no longer legendary just in my own mind! Like something I said? Donations gratefully accepted. LYLnTKvLefz9izJFUvEGQEZzSkz34b3N6U (Litecoin) 1GYbjMTPdCuV7dci3iCUiaRrcNuaiQrVYY (Bitcoin)
|
|
|
oslak
|
|
December 15, 2016, 09:16:58 AM |
|
Read Zec whitepaper and equihash. Not impressed. Ethereum offers better ingenuity in tech terms.
|
|
|
|
Havane
Jr. Member
Offline
Activity: 76
Merit: 3
|
|
December 15, 2016, 09:22:08 AM |
|
For me, payout take a lot of time with Dwarfpool
|
|
|
|
ghostfaceuk
|
|
December 15, 2016, 09:33:40 AM |
|
For me, payout take a lot of time with Dwarfpool
I'm happy with teh the payout times as long as I'm getting what I should for my hashrate (in fact as I stated earlier in thread I am at time getting more so no complaints from me)
|
|
|
|
QuintLeo
Legendary
Offline
Activity: 1498
Merit: 1030
|
|
December 15, 2016, 09:38:33 AM |
|
X11 is done due to some Chinese ASICs that are dominating all the hashpower and flooding the market with X11 chips.
Russian, actually, as far as the Baikal goes.
|
I'm no longer legendary just in my own mind! Like something I said? Donations gratefully accepted. LYLnTKvLefz9izJFUvEGQEZzSkz34b3N6U (Litecoin) 1GYbjMTPdCuV7dci3iCUiaRrcNuaiQrVYY (Bitcoin)
|
|
|
Yaunfitda
|
|
December 15, 2016, 09:41:29 AM |
|
Read Zec whitepaper and equihash. Not impressed. Ethereum offers better ingenuity in tech terms.
But it is anonymous.
|
|
|
|
HardSign
|
|
December 15, 2016, 09:42:11 AM |
|
Atrides (dwarfpool's developer) has fixed a lot rejects problem with Claymores miner 9.1. For last day I've received +25% profit comparing with flypool, and 1 (only one) rejected share for each rig (~0.01%)
|
|
|
|
c2n14
Newbie
Offline
Activity: 50
Merit: 0
|
|
December 15, 2016, 10:36:08 AM |
|
Atrides (dwarfpool's developer) has fixed a lot rejects problem with Claymores miner 9.1. It would be nice if he would fix the EU server connection problem once for all - now, the EU server is again @ 3000ms+
|
|
|
|
adorid
|
|
December 15, 2016, 10:47:04 AM |
|
try russian server, for me its 40-80ms
|
|
|
|
c2n14
Newbie
Offline
Activity: 50
Merit: 0
|
|
December 15, 2016, 10:55:33 AM |
|
try russian server, for me its 40-80ms
Yeah, I know. Just sad that after 3 days this problem still exists... Really, it would be nice if @Claymore would add a switch to his miner to change pools based on connection lag...
|
|
|
|
tistis96
Newbie
Offline
Activity: 8
Merit: 0
|
|
December 15, 2016, 11:00:33 AM |
|
Hi!
Can you please tell me what is this and why it happens:
socket was closed remotely ZEC: Connection lost, retry in 20 sec...
I have this problem just in v9.1
|
|
|
|
DStefanov
|
|
December 15, 2016, 11:10:31 AM |
|
Hi, Claymore! Will drop you in the near future a new version of your miner ZCash? Can a little more detail about the stability of version 10? Thanks
|
|
|
|
jenci
Newbie
Offline
Activity: 17
Merit: 0
|
|
December 15, 2016, 11:34:35 AM |
|
I have 2 x 750W PSU, each PSU runs 3 cards. I dont blame Claymore 9.0 or 9.1, I had this problem since the first time I use claymore, since 5.0. There will be 1 card always not working, will hash 0 H/s. After a certain of time, watchdog says that GPU hangs and reset. No matter how many GPU I use, there will be 1 not working. My temporary fix was keep rebooting until all GPUs working, but now that ways seems not work anymore.
if you overclock your GPUs try downclock it little or increase core voltage. i use claymore zcash miner from the first version. never had problem but after v9.0 i have problem with psu and gpu hangs. after adding second PSU and changing overclock settings problems is gone
|
|
|
|
|