PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[vagmor]

hello, i just try to mining with phoenixminer but all what i can see after start it is :
2020.12.26:18:17:08.565: main Phoenix Miner 5.1c Windows/msvc - Release build
2020.12.26:18:17:08.565: main Cmd line: -pool eu1.ethermine.org:4444 -pool2 us1.ethermine.org:4444 -wal ........................ -coin eth
2020.12.26:18:17:08.615: main CUDA version: 11.0, CUDA runtime: 8.0
2020.12.26:18:17:08.649: main No OpenCL platforms found
2020.12.26:18:17:08.649: main Available GPUs for mining:
2020.12.26:18:17:08.649: main GPU1: GeForce GTX 1080 Ti (pcie 2), CUDA cap. 6.1, 11 GB VRAM, 28 CUs
2020.12.26:18:17:08.649: main GPU2: GeForce GTX 1080 Ti (pcie 3), CUDA cap. 6.1, 11 GB VRAM, 28 CUs
 and after this all waht i see is : Press any key to continue and close the software

I have similar problem but with version 5.4c i have post before but still no answer from anybody
the miner crashing on startup...

Phoenix Miner 5.4c Windows/msvc - Release build
-----------------------------------------------

CUDA version: 11.0, CUDA runtime: 8.0
No OpenCL platforms found
Available GPUs for mining:
GPU1: GeForce RTX 3060 Ti (pcie 3), CUDA cap. 8.6, 8 GB VRAM, 38 CUs

C:\Users\vag.TOTHEMA\Desktop\eth miner>pause
Press any key to continue . . .

latest drivers...
latest software version... no luck

[aloneforever]

hello, i just try to mining with phoenixminer but all what i can see after start it is :
2020.12.26:18:17:08.565: main Phoenix Miner 5.1c Windows/msvc - Release build
2020.12.26:18:17:08.565: main Cmd line: -pool eu1.ethermine.org:4444 -pool2 us1.ethermine.org:4444 -wal ........................ -coin eth
2020.12.26:18:17:08.615: main CUDA version: 11.0, CUDA runtime: 8.0
2020.12.26:18:17:08.649: main No OpenCL platforms found
2020.12.26:18:17:08.649: main Available GPUs for mining:
2020.12.26:18:17:08.649: main GPU1: GeForce GTX 1080 Ti (pcie 2), CUDA cap. 6.1, 11 GB VRAM, 28 CUs
2020.12.26:18:17:08.649: main GPU2: GeForce GTX 1080 Ti (pcie 3), CUDA cap. 6.1, 11 GB VRAM, 28 CUs
 and after this all waht i see is : Press any key to continue and close the software

I have similar problem but with version 5.4c i have post before but still no answer from anybody
the miner crashing on startup...

Phoenix Miner 5.4c Windows/msvc - Release build
-----------------------------------------------

CUDA version: 11.0, CUDA runtime: 8.0
No OpenCL platforms found
Available GPUs for mining:
GPU1: GeForce RTX 3060 Ti (pcie 3), CUDA cap. 8.6, 8 GB VRAM, 38 CUs

C:\Users\vag.TOTHEMA\Desktop\eth miner>pause
Press any key to continue . . .

latest drivers...
latest software version... no luck

yea i try all ... only on hiveos working
on windows 10 last update , last driver not working

[zorachus99]

did you (or the pc) reset some settings in nvidia controll pannel?

No, yesterday the hashrate was changed automatically while mining

I fixed this issue by upgrading win7 to win10. Linux is OK too.
no need for a new serial shit even if your win7 is weirdly registered

I upgraded one of my boxes to 10 and it fixed the problem without any other updates or anything else needed.  Thanks for the tip.

[ivvi30]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

[invicta]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

It's probably Windows as it reserves more memory. Linux (or HiveOS) will get the most out of your 4GB cards. The DAG is over the limit and you're already suffering losses each epoch. My 4GB cards are still getting 22-24MH/s on this epoch.

[DGBfanster]

Lower hashrate and more rejects on RTX 3070 since the new epoch.

[Digital_Seytan]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

why you not mining ETC ?

[hesido]

Increased hashrate on Ethash by an average of 10%

Lol at the scammers trying to lure thirsty miners into downloading malware. As if a 10% increase in ethash would come in a frigging hotfix 5.4d. Good job deleting these posts. I'm sure some people are falling for it as they keep on posting these.

[adaseb]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

why you not mining ETC ?

Because mining ETC yields less than half the profits. Mining ETH is still most profitable on the 4GB. I got a few running on that lolminer but it runs at 24MH/s. Every DAG the speed slows down by 1 MH/s per DAG, most likely going to use for another 2 weeks and just craiglist the GPUs.

Nothing really worth mining with 4GB cards anymore. There is KawPow which yields like $0.25 after 10 cent power costs. ETH profits are almost triple of that. Then there are days when the fees are high and you can easily make 50-100% more profits.

Just sad you cant mine ETH anymore on the 4GB cards.

[Metroid]

Because mining ETC yields less than half the profits. Mining ETH is still most profitable on the 4GB. I got a few running on that lolminer but it runs at 24MH/s. Every DAG the speed slows down by 1 MH/s per DAG, most likely going to use for another 2 weeks and just craiglist the GPUs.

Nothing really worth mining with 4GB cards anymore. There is KawPow which yields like $0.25 after 10 cent power costs. ETH profits are almost triple of that. Then there are days when the fees are high and you can easily make 50-100% more profits.

Just sad you cant mine ETH anymore on the 4GB cards.

Funny, for the past 2 years prior july eth has been in negative profit, $0.10 per day per 30mhs net would have been great on those past 2 years but it was not even that, now on the bullrun that is just not good enough hehe, people are getting spoiled again. I agree with you, do not bother using them to mine anything else because as we know is not worth it, better just sell those 4gb while you can get a good price for them, there are gamers that want them, you will be able to sell for $100 ~ $150 easily.

[Deafran]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

Compute mode 

[Deafran]

For my 1000 mh/s Nanopool shows that i receive 0.04526 ETH per day.    

My concern is that my current and average hashrate at the pool-side is always hovering between 520-740 mh/s while the reported hashrate is accurate at 950-1000 mh/s


Mining ETC has no issue with this at all.   Average hashrate is pretty spot on with my reported hashrate.

yeah, its a bit low (0.04526)

i got 0.17343 - 0.18 xxx for 3Gh/s, some time can be 0.2xxxx ETH per day
2 month ago can reach 0.25xxx ETH per day

[carloshd]

"wdog 0" (disable) not working on Linux HiveOS "PhoenixMiner 5.4c", any solution?

[rdbase]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

Whoa! That is low compared to what they were getting last week at 21mh/s.
There was a chart showing the dates of each epoch and what mh/s the 4gb should still be getting until they hit those target dates. Just like the one which just past on the 24th.
I am still able to mine with my lone 4gb card at 21.5mh/s but it was at 31.5mh/s a month ago.
So the hashrate has been dropping off very rapidly every week.

[Deafran]

hello, i just try to mining with phoenixminer but all what i can see after start it is :
2020.12.26:18:17:08.565: main Phoenix Miner 5.1c Windows/msvc - Release build
2020.12.26:18:17:08.565: main Cmd line: -pool eu1.ethermine.org:4444 -pool2 us1.ethermine.org:4444 -wal ........................ -coin eth
2020.12.26:18:17:08.615: main CUDA version: 11.0, CUDA runtime: 8.0
2020.12.26:18:17:08.649: main No OpenCL platforms found
2020.12.26:18:17:08.649: main Available GPUs for mining:
2020.12.26:18:17:08.649: main GPU1: GeForce GTX 1080 Ti (pcie 2), CUDA cap. 6.1, 11 GB VRAM, 28 CUs
2020.12.26:18:17:08.649: main GPU2: GeForce GTX 1080 Ti (pcie 3), CUDA cap. 6.1, 11 GB VRAM, 28 CUs
 and after this all waht i see is : Press any key to continue and close the software

here my bat file for my 1080ti

PhoenixMiner.exe -pool eth-eu2.nanopool.org:9999 -wal 0xxxxxx -worker Zinc -epsw x -mode 1 -powlim -20 -tt -85 -tmax 85 -cclock +100 -mclock +600 -straps 5 -ftime 55 -nvNew 1 -Rmode 1 -log 0 -mport 0 -etha 0 -retrydelay 1 -coin eth
pause

phoenixminer.exe-run as administrator
win10

and not using after burner

[dragonmike]

3060 Ti here - works well, unless...

- I set max overclock at start (only incorrect shares are generated - I need to start lower and increase)
- Epoch changes (same result as above)

Please fix.

happens to me as well (RTX3070), I thought it was a bug on the driver or the bios, I was updating/flashing for 2 hours before figured what you just said lol

Interesting.. thanks for reporting this.. did you try any other miner see if the same issue persists?
so it is not a driver issue, it is a general rtx 3000 series issue

If I start on +1200 mem clock I can survive  but I still get bunch of invalid shares ,  if i start under +1000mem clock and go up I get no invalid shares even up to 1500+for now I start them at +900 and go up to +1200 since you never know when the Epoch change happens and the whole thing goes down if you have it set above +1250 or so memory clock




I have an MSI and a Zotac  3060 ti ,   Zotac runs hotter and faster , but more prone to invalid shares, same story as above applies to both

I get 59-60 MH on the 900+ mem
and can get close to 64 MH if I go up to +1500 and give it some  power like 66% to 68%

Happens when dual-mining with ZIL too.
Have you tried another miner?

[ivvi30]

PhoenixMiner 5.4c: Asus rog strix RX570 4gb ETH 11,92mh
https://ibb.co/YP4X8V7

Compute mode 

so included!

[vagmor]

3060 Ti here - works well, unless...

- I set max overclock at start (only incorrect shares are generated - I need to start lower and increase)
- Epoch changes (same result as above)

Please fix.

happens to me as well (RTX3070), I thought it was a bug on the driver or the bios, I was updating/flashing for 2 hours before figured what you just said lol

Interesting.. thanks for reporting this.. did you try any other miner see if the same issue persists?
so it is not a driver issue, it is a general rtx 3000 series issue

If I start on +1200 mem clock I can survive  but I still get bunch of invalid shares ,  if i start under +1000mem clock and go up I get no invalid shares even up to 1500+for now I start them at +900 and go up to +1200 since you never know when the Epoch change happens and the whole thing goes down if you have it set above +1250 or so memory clock




I have an MSI and a Zotac  3060 ti ,   Zotac runs hotter and faster , but more prone to invalid shares, same story as above applies to both

I get 59-60 MH on the 900+ mem
and can get close to 64 MH if I go up to +1500 and give it some  power like 66% to 68%

Happens when dual-mining with ZIL too.
Have you tried another miner?

same here with 2 3060ti to 2 different rigs with exactly this behavior

[groovytechno]

For my 1000 mh/s Nanopool shows that i receive 0.04526 ETH per day.    

My concern is that my current and average hashrate at the pool-side is always hovering between 520-740 mh/s while the reported hashrate is accurate at 950-1000 mh/s


Mining ETC has no issue with this at all.   Average hashrate is pretty spot on with my reported hashrate.

yeah, its a bit low (0.04526)

i got 0.17343 - 0.18 xxx for 3Gh/s, some time can be 0.2xxxx ETH per day
2 month ago can reach 0.25xxx ETH per day

Interesting.   Mind if I ask what pool and mining software you're using?

[HappySwedishGuy]

Is it possible to do so it mines at another adress for an short period of time? Just like the devfee kinda but to another adress aswell