PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[BitKingRoss]

Im using 5 x Nvidia P104-100 4GB, havent used these rigs for well over 2 years.
Now I installed PhoenixMiner 5.4c and when I run the "start_miner" file, it quickly close the cmd window (I managed to printscreen) before they close each time I run. Any idea what seems to be the problem and solution would be very much appreciated.
https://imgur.com/3zKkh6u

It basically says "No OpenCL platforms found"

Try 4.9c. None of the 5.x versions work for my Evga p104s. But 4.9c ive had running for about 10 days since I switched form 5 to 4.9.

[1714793958]

1714793958

[1714793958]

1714793958

[1714793958]

1714793958

[duplj30]

0x00007FFC3FB499E9 (0x00000261DBA3A5D8 0x00000261DC62A190 0x000000820BFFF989 0x0000000000000000), aclWriteToMem() + 0x14E6AA9 bytes(s)
0x00007FFC3E3D217E (0x0000000000000000 0x000000820BFFF968 0x00000261DC62A190 0x0000000000000020), clGetPipeInfo() + 0x2114E bytes(s)
0x00007FFC3E46DF6B (0x0000000000000100 0x00000261DC629FC0 0x000000820BFFF989 0x000000820BFFFB18), clGetPipeInfo() + 0xBCF3B bytes(s)
Eth: Mining ETH on eu1.ethermine.org:4444 for 0:00
0x00007FFC3E48EC0C (0x0000000000000020 0x00000261DC4FC3D5 0x00000261DC584850 0x000000820BFFFB18), clGetPipeInfo() + 0xDDBDC bytes(s)
0x00007FFC3E48EFFD (0x00000261DC584908 0x00000261DC629FD8 0x000000820BFFFB49 0x0000000000000020), clGetPipeInfo() + 0xDDFCD bytes(s)
0x00007FFC3E480756 (0x00000261EB539B40 0x00000261DC4FD000 0x0000000000000000 0x000000820BFFFC69), clGetPipeInfo() + 0xCF726 bytes(s)
0x00007FFC3E3C1F8B (0x00000261EB8930B0 0x00000261DC629FC0 0x00000261EB8930B0 0x00000261DC2A2180), clGetPipeInfo() + 0x10F5B bytes(s)
0x00007FFC3E3C208B (0x0000000000000000 0x0000000000000000 0x00000261DC4E7A60 0x00000261DC4E7A60), clGetPipeInfo() + 0x1105B bytes(s)
0x00007FFC3E3B1CB5 (0x00000261DC4E7A60 0x0000000000000001 0x0000000000000000 0x0000000000000000), clGetPipeInfo() + 0xC85 bytes(s)
0x00007FFC3E3D2149 (0x0000000000000000 0x0000000000000000 0x0000000000000000 0x0000000000000000), clGetPipeInfo() + 0x21119 bytes(s)
0x00007FFC74057034 (0x0000000000000000 0x0000000000000000 0x0000000000000000 0x0000000000000000), BaseThreadInitThunk() + 0x14 bytes(s)
0x00007FFC751DD0D1 (0x0000000000000000 0x0000000000000000 0x0000000000000000 0x0000000000000000), RtlUserThreadStart() + 0x21 bytes(s)
Eth: Accepted shares 0 (0 stales), rejected shares 0 (0 stales)

D:\üretim\mining\PhoenixMiner_5.4c_Windows_AMD_NVIDIA.Password-phoenix (1)\PhoenixMiner_5.4c_Windows_AMD_NVIDIA (Password-phoenix)>pause
Press any key to continue . . .

help me  asrock rx 5700 xt phantom gaming

this is a memory overclocking error
you need to either reduce the memory frequency
or step by step increase the memory voltage (mvdd) and a little SOC voltage and test further

[deluk0]

Hi, I am using Phoenix Miner 5.4c Linux/gcc - Release build on Ubuntu 20.04.1 with Asus dual-rx5700xt-o8g-evo. Installed AMD drivers 20.45, for which had to downgrade the kernel to 5.4.0-54-generic. However the miner does not seem to recognize the drivers:

2021.01.10:05:17:20.716: main Unknown OpenCL driver version! Hashrate and stale shares may suffer
2021.01.10:05:17:20.716: main OpenCL platform: OpenCL 2.0 AMD-APP (3188.4)
2021.01.10:05:17:20.716: main Available GPUs for mining:
2021.01.10:05:17:20.716: main GPU1: AMD Radeon RX 5700 XT (pcie 25), OpenCL 2.0, 8 GB VRAM, 40 CUs
2021.01.10:05:17:20.717: main AMD sysfs monitor initialized

I am getting 53-54 Mh/s, which seems normal for rx5700xt. Would it get any better if the miner recognized the drivers? Should I worry about drivers not being recognized?

[seantcm]

Im using 5 x Nvidia P104-100 4GB, havent used these rigs for well over 2 years.
Now I installed PhoenixMiner 5.4c and when I run the "start_miner" file, it quickly close the cmd window (I managed to printscreen) before they close each time I run. Any idea what seems to be the problem and solution would be very much appreciated.
https://imgur.com/3zKkh6u

It basically says "No OpenCL platforms found"

Try 4.9c. None of the 5.x versions work for my Evga p104s. But 4.9c ive had running for about 10 days since I switched form 5 to 4.9.

Thanks mate. I'm lucky to have your answer =) Wil try em out now.

Btw another rig of mine has 4xP104-100 (4GB) and 1xRX580. May I know how do it set them up to mine without issues? Do i have to use dual mining only able to maximise them?

[badassmf]

Hi.
I Install PhoenixMiner For The First Time. I'm trying with PhoenixMiner 5.1c. The miner does not manage the video cards correctly according to the settings in the config file, in particular the control of the fans and the downclock of the memory and GPU frequencies. I tried different versions of the drivers listed here as "Good Drivers", but with all the problem is the same. What do I need to do to get the miner himself to manage the cards and to override the video card bios?

My Rig: 14xRX580 Asus Rog Strix 8Gb GDDR5 Samsung on ASUS 250 Mining Expert. My VBIOS are overclocked - GPU on 1350 MHz and Memory on 2000 MHz. I use Windows 10 64 Pro 2002 - MBR-CSM and AMD Radeon Software Adrenalin 20.4.2-may25.
These are my config file settings:
-coin eth
-amd
-acm
-allpools 1
-stales 1
-ftimeout 10
-bench
-altinit
-resetoc
-mi 12
-tt 50
-ttli 75
-tstop 85
-tstart 50
-fcm 2
-ethi 8
-fanmin 40
-fanmax 100
-gser 1
-eres 6
-estale 1
-mode 1
-rxboost 1
-cclock 1160
-cvddc 860
-mclock 1800
-mvddc 860

[batsonxl]

Hi.
I Install PhoenixMiner For The First Time. I'm trying with PhoenixMiner 5.1c. The miner does not manage the video cards correctly according to the settings in the config file, in particular the control of the fans and the downclock of the memory and GPU frequencies. I tried different versions of the drivers listed here as "Good Drivers", but with all the problem is the same. What do I need to do to get the miner himself to manage the cards and to override the video card bios?

My Rig: 14xRX580 Asus Rog Strix 8Gb GDDR5 Samsung on ASUS 350 Mining Expert. My VBIOS are overclocked - GPU on 1350 MHz and Memory on 2000 MHz. I use Windows 10 64 Pro 2002 - MBR-CSM and AMD Radeon Software Adrenalin 20.4.2-may25.
These are my config file settings:
-coin eth
-amd
-acm
-allpools 1
-stales 1
-ftimeout 10
-bench
-altinit
-resetoc
-mi 12
-tt 50
-ttli 75
-tstop 85
-tstart 50
-fcm 2
-ethi 8
-fanmin 40
-fanmax 100
-gser 1
-eres 6
-estale 1
-mode 1
-rxboost 1
-cclock 1160
-cvddc 860
-mclock 1800
-mvddc 860

wooow you should add more commands. just kidding.why dont you delete all this and start step by step, no commands just a pool and wallet.

[dummyminer]

Hi.
I Install PhoenixMiner For The First Time. I'm trying with PhoenixMiner 5.1c. The miner does not manage the video cards correctly according to the settings in the config file, in particular the control of the fans and the downclock of the memory and GPU frequencies. I tried different versions of the drivers listed here as "Good Drivers", but with all the problem is the same. What do I need to do to get the miner himself to manage the cards and to override the video card bios?

My Rig: 14xRX580 Asus Rog Strix 8Gb GDDR5 Samsung on ASUS 350 Mining Expert. My VBIOS are overclocked - GPU on 1350 MHz and Memory on 2000 MHz. I use Windows 10 64 Pro 2002 - MBR-CSM and AMD Radeon Software Adrenalin 20.4.2-may25.
These are my config file settings:
-coin eth
-amd
-acm
-allpools 1
-stales 1
-ftimeout 10
-bench
-altinit
-resetoc
-mi 12
-tt 50
-ttli 75
-tstop 85
-tstart 50
-fcm 2
-ethi 8
-fanmin 40
-fanmax 100
-gser 1
-eres 6
-estale 1
-mode 1
-rxboost 1
-cclock 1160
-cvddc 860
-mclock 1800
-mvddc 860

wooow you should add more commands. just kidding.why dont you delete all this and start step by step, no commands just a pool and wallet.

PhoniexMiner cannot correctly manage it because Asus never released 350 Mining Expert mono.

[duplj30]

Hi.
I Install PhoenixMiner For The First Time. I'm trying with PhoenixMiner 5.1c. The miner does not manage the video cards correctly according to the settings in the config file, in particular the control of the fans and the downclock of the memory and GPU frequencies. I tried different versions of the drivers listed here as "Good Drivers", but with all the problem is the same. What do I need to do to get the miner himself to manage the cards and to override the video card bios?

My Rig: 14xRX580 Asus Rog Strix 8Gb GDDR5 Samsung on ASUS 350 Mining Expert. My VBIOS are overclocked - GPU on 1350 MHz and Memory on 2000 MHz. I use Windows 10 64 Pro 2002 - MBR-CSM and AMD Radeon Software Adrenalin 20.4.2-may25.
These are my config file settings:
-coin eth
-amd
-acm
...

wooow you should add more commands. just kidding.why dont you delete all this and start step by step, no commands just a pool and wallet.

PhoniexMiner cannot correctly manage it because Asus never released 350 Mining Expert mono.

apparently we are talking about a b250 mining expert
But has Windows already learned to understand more than 12 video cards?
I have the same system board with ten cards for Windows 10 and drivers 20.5.1, everything works fine

-coin eth -amd -acm -mi 14 -gt 0,0,56,62,65,67,66,68,65,62 -clkernel 1 -clNew 1 -retrydelay 10 -fret 10 -gsi 10 -gswin 30 -ftimeout 180 -ptimeout 10 -stales 1 -eres 10 -clf 1 -gser 0 -lidag 0 -dbg 0 -log 1 -cvddc 718,712,893,1006,881,1000,1012,1006,881,993 -mvddc 0,0,800,800,800,800,800,800,899,800 -cclock 0,0,1260,1240,1240,0,1240,1240,1240,0 -wdog 0 -wdtimeout 120 -tt 61 -tstop 65 -ttli 63 -tstart 50 -astats 1 -hstats 2 -gbase 0 -ppf 100 -fcm 0 -fanmin 0,0,50,50,50,50,50,50,50,50 -clGreen 0 -rate 1 -rxboost 0 -daglim 0 -vmr 0,0,25,20,20,25,25,25,25,20

[Toughit]

how does PM calculate effect hash and at pool stats?

Why are both of those numbers so much lower than my hash rate even with zero rejects?

[STAT303954]

Has anyone had an issue mixing 580s with Vega 56 together on the same rig??? Just tried today adding a 56 to my 580s and can not control the fan speed either in Afterburner or the miner...its the strangest thing because my 580s fan just stay off after starting Windows

[duplj30]

how does PM calculate effect hash and at pool stats?

Why are both of those numbers so much lower than my hash rate even with zero rejects?

Q007: What is the meaning of "effective speed" shown by PhoenixMiner's statistics?
   A: This is a measure of the actually found shares, which determines how the pool sees your
   miner hashrate. This number should be close to the average hashrate of your rig (usually a 2-4%
   lower than it) depending you your current luck in finding shares. This statistic is meaningless
   in the first few hours after the miner is started and will level off to the real value with
   time.
 
Q008: Why is the effective hashrate shown by the pool lower than the one shown by PhoenixMiner?
   A: There are two reasons for this: stale shares and luck. The stale shares are rewarded at only
   about 50-70% by most pools. The luck factor should level itself off over time but it may take
   a few days before it does. If your effective hashrate reported by the pool is consistently lower
   than the hashrate of your rig by more than 5-7% than you should look at the number of stale shares
   and the average share acceptance time - if it is higher than 100 ms, try to find a pool that is
   near to you geographically to lower the network latency. You can also restart your rig, or
   try another pool.

[ZZSiro]

Dear mining fellows,
I spend some time testing this miner using Asus Vega64. Neither ubuntu nor windows platform was stable mining and not even talking about performance.
If someone figured it out please post your configuration. I guess I am not the only one...

OS / OS Version / driver version / (kernel version) / (kernel mods) / miner parameters

Cheers, ZZSiro
---

[miner29]

Dear mining fellows,
I spend some time testing this miner using Asus Vega64. Neither ubuntu nor windows platform was stable mining and not even talking about performance.
If someone figured it out please post your configuration. I guess I am not the only one...

OS / OS Version / driver version / (kernel version) / (kernel mods) / miner parameters

Cheers, ZZSiro
---

My Vegas go 50-56mhs on mmpos and trm.

Vegas are different beasts for sure.  But with mmpos and trm super stable

[dummyminer]

how does PM calculate effect hash and at pool stats?

Why are both of those numbers so much lower than my hash rate even with zero rejects?

Q007: What is the meaning of "effective speed" shown by PhoenixMiner's statistics?
   A: This is a measure of the actually found shares, which determines how the pool sees your
   miner hashrate. This number should be close to the average hashrate of your rig (usually a 2-4%
   lower than it) depending you your current luck in finding shares. This statistic is meaningless
   in the first few hours after the miner is started and will level off to the real value with
   time.
 
Q008: Why is the effective hashrate shown by the pool lower than the one shown by PhoenixMiner?
   A: There are two reasons for this: stale shares and luck. The stale shares are rewarded at only
   about 50-70% by most pools. The luck factor should level itself off over time but it may take
   a few days before it does. If your effective hashrate reported by the pool is consistently lower
   than the hashrate of your rig by more than 5-7% than you should look at the number of stale shares
   and the average share acceptance time - if it is higher than 100 ms, try to find a pool that is
   near to you geographically to lower the network latency. You can also restart your rig, or
   try another pool.

It’s shocking how a newbie member reads and understands how mining works - but a full member does not!

I’m going to give you your 1st well-deserved trust.

[mrbugera2]

what this means?

[miner29]

what this means?

Its the date Jan 11th...and time miner has been running and time.

[scryptr]

DOES ANYONE KNOW HOW TO RUN PHOENIXMINER AS ROOT ON ETHOS? --

I run ethOS mining system, a hybrid of Ubuntu 14.04 and 16.04.  PhoenixMiner is very stable in this system, and will run literally for months without crashing.  But, I cannot run PM with straps unless it runs with root priviledges.

Does anyone know how?   Thanks in advance...       --scryptr

[Deafran]

DOES ANYONE KNOW HOW TO RUN PHOENIXMINER AS ROOT ON ETHOS? --

I run ethOS mining system, a hybrid of Ubuntu 14.04 and 16.04.  PhoenixMiner is very stable in this system, and will run literally for months without crashing.  But, I cannot run PM with straps unless it runs with root priviledges.

Does anyone know how?   Thanks in advance...       --scryptr

https://github.com/cynixx3/third-party-miner-installer-for-ethos

https://miningclub.info/threads/miner-manager-dlja-ethos.59413/

[scryptr]

THANKS--

But that does not answer my question.  I use Miner-Manager often, but it does not do anything to launch a miner.  It will update a miner or add a new miner to the system.

It may take a system mod to do what I want.  I want to launch and run PhoenixMiner as root.       --scryptr

[br2459]

THANKS--

But that does not answer my question.  I use Miner-Manager often, but it does not do anything to launch a miner.  It will update a miner or add a new miner to the system.

It may take a system mod to do what I want.  I want to launch and run PhoenixMiner as root.       --scryptr

This might sound stupid but have you tried sudo and the start_miner.sh? or su and start_miner.sh?