PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[murgorx]

has anyone been able to mine on the Binance's ETH pool? I am getting really stuck with configuring the phoenixminer bat file..

[sohbetchar]

good +rep tx.

[rdluffy]

has anyone been able to mine on the Binance's ETH pool? I am getting really stuck with configuring the phoenixminer bat file..

Last week I did the tests and the correct config is:

PhoenixMiner.exe -pool stratum+tcp://ethash.poolbinance.com:1800 -pool2 stratum+tcp://ethash.poolbinance.com:25 -wal nameofworker.nameofworker

Look: There's the first pool with port 1800, the second pool port 25, and last is the name of the worker you'll create on Binance: https://www.binance.com/en/support/faq/9bd21a9536d74d1fb65c83f8e60ded93

Lets say you'll use the name murgorx, the line will be:

PhoenixMiner.exe -pool stratum+tcp://ethash.poolbinance.com:1800 -pool2 stratum+tcp://ethash.poolbinance.com:25 -wal murgorx.murgorx


And it's normal to have some delay until pool recognize your hashrate correctly, but don't worry, it's normal and they will pay from 1st share

[CGS_CC]

I am new to PhoenixMiner so please go easy on me as I have a couple questions

Is there a way to see when the last share was found?(besides scrolling back up the screen or looking at the log file)

I am running rx580 cards  -rxboost is working fine "xxxx.xx.xx:00:18:35.996: hwmc GPU1: set VRAM refresh rate -rxboost 30 (equal to -vmr 29)" but I see nothing indicating straps are being applied.  Will I get a notice or is it just working and I dont see it?

Thanks

[hustleman]

I am new to PhoenixMiner so please go easy on me as I have a couple questions

Is there a way to see when the last share was found?(besides scrolling back up the screen or looking at the log file)

I am running rx580 cards  -rxboost is working fine "xxxx.xx.xx:00:18:35.996: hwmc GPU1: set VRAM refresh rate -rxboost 30 (equal to -vmr 29)" but I see nothing indicating straps are being applied.  Will I get a notice or is it just working and I dont see it?

Thanks

What is the cards performance?  What MHS are/is it producing?

[CGS_CC]

I am new to PhoenixMiner so please go easy on me as I have a couple questions

Is there a way to see when the last share was found?(besides scrolling back up the screen or looking at the log file)

I am running rx580 cards  -rxboost is working fine "xxxx.xx.xx:00:18:35.996: hwmc GPU1: set VRAM refresh rate -rxboost 30 (equal to -vmr 29)" but I see nothing indicating straps are being applied.  Will I get a notice or is it just working and I dont see it?

Thanks

What is the cards performance?  What MHS are/is it producing?

I am getting 28.6-28.8 MHS on the cards @ 90w with settings of 1175mhz on GPU and 2150mhz on memory. Oh and stock BIOS.

[Seph213]

Hey guys

Been using phoenixminer and liking it , i’m hashing at 130mhs constantly on nanopool .Barely any stale share . I see my hashrate reported between 120-130 .

Now when i look on whattomine , i shpuld be generating .21 to .24eth a month but i seem to be getting .2 only .

Any of u guys have been in this situation and were able to fix it ?

Thanks

[hesido]

Hey guys

Been using phoenixminer and liking it , i’m hashing at 130mhs constantly on nanopool .Barely any stale share . I see my hashrate reported between 120-130 .

Now when i look on whattomine , i shpuld be generating .21 to .24eth a month but i seem to be getting .2 only .

Any of u guys have been in this situation and were able to fix it ?

Thanks

Try mining on a different pool, maybe Ethermine. Having said that I wouldn't say no if more people joined flexpool, it's a small pool with bigger variance but it's worth a shot. The PPLNS window is too long so don't worry about inial estimates being too low, you will be getting full rewards in a couple blocks found by pool and you will keep on receiving after you leave for a couple of blocks found.

[Seph213]

Hey guys

Been using phoenixminer and liking it , i’m hashing at 130mhs constantly on nanopool .Barely any stale share . I see my hashrate reported between 120-130 .

Now when i look on whattomine , i shpuld be generating .21 to .24eth a month but i seem to be getting .2 only .

Any of u guys have been in this situation and were able to fix it ?

Thanks

Try mining on a different pool, maybe Ethermine. Having said that I wouldn't say no if more people joined flexpool, it's a small pool with bigger variance but it's worth a shot. The PPLNS window is too long so don't worry about inial estimates being too low, you will be getting full rewards in a couple blocks found by pool and you will keep on receiving after you leave for a couple of blocks found.

I have 2 pools in mind to switch .

Starkpool that does pps and 2miners pool since they also opposed to eip 1559


Could consider flexpool , lots of buzz about it recently and they oppose eip 1559

Whats the difference in revenue between a big pool like starkpool and flexpool ?

[wolverine5pl]

3070 getting quiet few invalid shares. but using t-rex is all fine 100% correct. any clue why

[miner29]

Hey guys

Been using phoenixminer and liking it , i’m hashing at 130mhs constantly on nanopool .Barely any stale share . I see my hashrate reported between 120-130 .

Now when i look on whattomine , i shpuld be generating .21 to .24eth a month but i seem to be getting .2 only .

Any of u guys have been in this situation and were able to fix it ?

Thanks

Try mining on a different pool, maybe Ethermine. Having said that I wouldn't say no if more people joined flexpool, it's a small pool with bigger variance but it's worth a shot. The PPLNS window is too long so don't worry about inial estimates being too low, you will be getting full rewards in a couple blocks found by pool and you will keep on receiving after you leave for a couple of blocks found.

I could not like the Ethermine pool.
While the my miner softwares cannot find any errors, Ethermine shows bad shares on the site

Then pick another ETH pool...if you get similar results the issues not the pool.  I can go between nano & ethmine and not see any real difference in payout.  Sounds like you have an issue as Ethermine is showing bad shares.  Nano may not report them but that doesnt mean they are not occuring.  I generally earn more than Whattomine states for my hasih power.  I also regularly earn slightly more than the estimate on ethermine.  

Are you on 5.4c PhoenixMiner?  Bad internet connection?  

[Seph213]

Hey guys

Been using phoenixminer and liking it , i’m hashing at 130mhs constantly on nanopool .Barely any stale share . I see my hashrate reported between 120-130 .

Now when i look on whattomine , i shpuld be generating .21 to .24eth a month but i seem to be getting .2 only .

Any of u guys have been in this situation and were able to fix it ?

Thanks

Try mining on a different pool, maybe Ethermine. Having said that I wouldn't say no if more people joined flexpool, it's a small pool with bigger variance but it's worth a shot. The PPLNS window is too long so don't worry about inial estimates being too low, you will be getting full rewards in a couple blocks found by pool and you will keep on receiving after you leave for a couple of blocks found.

I could not like the Ethermine pool.
While the my miner softwares cannot find any errors, Ethermine shows bad shares on the site

Then pick another ETH pool...if you get similar results the issues not the pool.  I can go between nano & ethmine and not see any real difference in payout.  Sounds like you have an issue as Ethermine is showing bad shares.  Nano may not report them but that doesnt mean they are not occuring.  I generally earn more than Whattomine states for my hasih power.  I also regularly earn slightly more than the estimate on ethermine.  

Are you on 5.4c PhoenixMiner?  Bad internet connection?  

Out of curiosity why not mine on sparkpool ? Bigger pool , pps+ , wouldn't that be a better choice than nano/ether?

Would give it a try if i could simply put my wallet and point my miner at their pool but with the annoying registration , having to put ur phone number and authenticator for payments it gets complicated for nothing.

[x-dream]

Anyone know what these parameters do? Could not find the answer in the readme.txt

-epsw x
-mode 1
-Rmode 1
-mport 0
-etha 0

[alucard20724]

Anyone know what these parameters do? Could not find the answer in the readme.txt

-epsw x
-mode 1
-Rmode 1
-mport 0
-etha 0

Read the first post.  it's in the OP

https://bitcointalk.org/index.php?topic=2647654.0

[roony94]

Hi,
I'am getting this error since 10 days agora:

clSetKernelArg (-48)

@PhoenixMiner How can we solve this? I see that there are many other users on reddit experiencing the same issue.

[Geniusvzla]

Hey guys

Been using phoenixminer and liking it , i’m hashing at 130mhs constantly on nanopool .Barely any stale share . I see my hashrate reported between 120-130 .

Now when i look on whattomine , i shpuld be generating .21 to .24eth a month but i seem to be getting .2 only .

Any of u guys have been in this situation and were able to fix it ?

Thanks

Try mining on a different pool, maybe Ethermine. Having said that I wouldn't say no if more people joined flexpool, it's a small pool with bigger variance but it's worth a shot. The PPLNS window is too long so don't worry about inial estimates being too low, you will be getting full rewards in a couple blocks found by pool and you will keep on receiving after you leave for a couple of blocks found.

Greetings, I had that dilemma for a while and in the end after several tests I stayed in Nanopool because the payment was always higher.
In Ethermine I found more shares but we know that they are worth 3 times less than Nanopool shares and in the end the payment should be the same or very approximate in the 2 pools but in my case I have received a higher payment in Nanopool.

On the other hand, you should know that the information provided by whattomine is referenced by the Linux system.

[SirDruid]

hi I have a Gigabyte RX580 Windforce OC Rev 2.0, settings are cclock 1200, cvddc 850, mclock 2015 mvddc 875, currently it's giving me 27 MHs, come times reach 28.

I testes many different configurations but reaching the 30 MHs reported on many post.

Anyone else having this issue or a good config for this card?

Thanks

[waywoos]

hi I have a Gigabyte RX580 Windforce OC Rev 2.0, settings are cclock 1200, cvddc 850, mclock 2015 mvddc 875, currently it's giving me 27 MHs, come times reach 28.

I testes many different configurations but reaching the 30 MHs reported on many post.

Anyone else having this issue or a good config for this card?

Thanks

try 2150 for mclock

[kiki456]

Can you help me please. I have 4x Rx580 and 1x Rx5700, and amd driver randomly crashed. In log i can see hashrate of rx5700 jump high 469mh, and drop to 0mh.

The same thing happens on 20.9.1 and 20.11.2 version driver. I revert default clock for rx5700 and problem it happens again.

Do you have advice how to solve this problem.

i use 5.4c Phoenix miner.

[CGS_CC]

I am new to PhoenixMiner so please go easy on me as I have a couple questions.

Is there a way to see when the last share was found?(besides scrolling back up the screen or looking at the log file)

I am running rx580 cards  -rxboost is working fine "xxxx.xx.xx:00:18:35.996: hwmc GPU1: set VRAM refresh rate -rxboost 30 (equal to -vmr 29)" but I see nothing indicating straps are being applied.  Will I get a notice or is it just working and I dont see it?

Thanks

Im running about 28.6 -28.8 mhs at 1175mhz GPU and 2150mhz memory at 90w but feel i should be above 30mhz.