Call_Me_Bambi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2017, 10:38:17 PM |
|
I have 5x RX480 (Saphhire Nitro +) with Blockchain drivers and custom BIOS. I'm limited to 1000W power. I'm currently mining ETH + LBRY but I have some wierd errors. GPU stops every few minutes and then starts again... I tryed lowering dcri but no help. Now my settings are:
Clock: 1050 Voltage: 950 Memory: 2080 voltage: 950
Can you tell me what settings on GPU do you use for this combination?
I think others have replied to this but just to add my tuppence worth, I think you are sailing to close to the wind with a 1000 Watt PSU and dual mining. It can depend on the PSU you are using, I have a 1000 Watt EVGA Gold (6 card rig) and it worked OK at over 1000 Watts (long story, but put a quick stop to that as it is not recommended). If your rig works OK mining other coins then you are probably over stressing your PSU, remember the rig will take a little extra when it first starts up and if the GPU fans start to run at higher speeds. I found dual mining too stessful for my poor cards. Get a power monitor and check exactly how much the rig takes from the wall.
|
|
|
|
morgan-12l1
Newbie
Offline
Activity: 2
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 12:02:03 AM |
|
Пpoблeмa в тoм чтo xeшpeйт пaдaeт дo нyля и вылeтaeт c oшибкoй? Cyдя пo лoгaм, y тeбя пepepaзгoн, yмeньши чacтoтy пaмяти и нe paзгoняй ядpo.
y мeня 1 кapтa 1060 c чипaми caмcyнг. paзгoн cдeлaн пaмяти дo 1000 (мaкc), core cklock +98+110 гдe тo. питaниe нe paзгoнял, ceйчac ктo тo coвeтoвaл чтo чyть дoбaвил пepecтaли вpoдe oшибки быть. cyть былa в тoм, чтo чepeз вpeмя зaxoжy нa aвтoбepнepe пoкaзывaeтcя 0 гpaфичecкoe ядpo.. a дoбычa идeт. дo этoгo нa этoй жe вepcии мaйнepa 9.3 вce paбoтaлo oтличнo etc sia - мecяцaми нe тpoгaл. и чтo глaвнoe тeмпepaтypa кaк paньшe дo 66-68 в ocнoвнoм мaкc пoднимaeтcя (кoгдa paньшe cмoтpeл) и ceйчac. нo вcтaeт. кaк тoлькo нa decred пepeшeл нaчaлacь дaннaя cитyaция ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) p.s тoгдa кaкиe знaчeния лyчшe для paзгoнa мoeй кapты? eng: I have 1 map 1060 c chips Samsung. overclocking made the memory to 1000 (max), core cklock +98+110 somewhere. meals are not dispersed, now someone is advised that a little added stopped like mistakes to be made. the essence was that through the time I go on autobrennero shows 0 GPU.. and mining is done. before on the same version miner 9.3, everything is working fine etc sia - months did not touch. and most importantly, the temperature as before, until 66-68 basically max rises (when looking ahead) now. but it raises. as soon as decred passed began this situation:( p.s then what value is best for overclocking my card?
|
|
|
|
STT
Legendary
Offline
Activity: 4032
Merit: 1444
Exchange 250+ Coins With 0% Fees
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 08:46:39 AM |
|
I have 5x RX480 (Saphhire Nitro +) with Blockchain drivers and custom BIOS. I'm limited to 1000W power. I'm currently mining ETH + LBRY but I have some wierd errors. GPU stops every few minutes and then starts again... I tryed lowering dcri but no help. Now my settings are:
Clock: 1050 Voltage: 950 Memory: 2080 voltage: 950
Can you tell me what settings on GPU do you use for this combination?
I think others have replied to this but just to add my tuppence worth, I think you are sailing to close to the wind with a 1000 Watt PSU and dual mining. It can depend on the PSU you are using, I have a 1000 Watt EVGA Gold (6 card rig) and it worked OK at over 1000 Watts (long story, but put a quick stop to that as it is not recommended). If your rig works OK mining other coins then you are probably over stressing your PSU, remember the rig will take a little extra when it first starts up and if the GPU fans start to run at higher speeds. I found dual mining too stessful for my poor cards. Get a power monitor and check exactly how much the rig takes from the wall. Depends on the quality of the PSU and allegedly the ageing of the PSU also reduces its capacity (I think the pace of ageing depends on type of use also). The rough estimate is about 10% a year so a rough calculation for 6 years of PSU use would be 1000 (0.9^6) = 1000(0.531441) = 531w Ive wanted multiple PSU setups for ages and its more common now, probably an old deal on servers. Ive never heard of a PSU tester though, somebody knows no doubt
|
| | TheChange | | | | |
░░░░░░░░░░██▄ ▄▄▄▄▄▄▄▄▄▄▄███▄ ▀▀▀▀▀▀▀▀▀▀▀███▀ ░░░░░░░░░░██▀ ░░░▄▄ ▄██▀ ███████████████ ▀██▄ ░░░▀▀ | | | | +250 COINS | | ..Crypto Exchange.. | │ | ▄▄▄▄ ▄▄▄███▀▀███▄▄▄ ▄█████▀▀░▄▄▄▄░▀▀█████▄ ██▀░▄▄▄████████▄▄▄░▀██ ██░████████████████░██ ██░████████████████░██ ██░▀██████████████▀░██ ██░▀████████████▀░██ ▀██░▀██████████▀░██▀ ▀██▄░▀██████▀░▄██▀ ▀██▄▄░▀▀░▄▄██▀ ▀▀██▄▄██▀▀ ▀▀▀▀ | | | │ | |
|
|
|
stef_stef
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 09:30:22 AM |
|
Guys, what are you dual mining at the moment?
|
|
|
|
blue1984
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 75
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 10:13:03 AM |
|
Hello, I use the 470 (modded Bios - Timings / VCC Offset) with claymore 9.7 i get 27,5 MHS (100 Watt from the wall) before the DAG file Problem. now i get with Claymore 10.1 only 24,5 MHS - with the lattest driver and with the driver von 23.8 -> what driver do you use for BIOS modded AMD GPUS (Driversetting) to get again the 27,5 MHS?
|
|
|
|
bonuscrypto
Newbie
Offline
Activity: 6
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 11:21:53 AM |
|
Greetings! My first post here and a noob ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) It would be nice if someone can take a quick look at my start.bat and advise if I should tweak some parameters. There's just ONE line: EthDcrMiner64.exe -epool stratum+tcp://eth.suprnova.cc:5005 -ewal username.worker1 -esm 0 -epsw x -allpools 1 -mport -3333 -dpool stratum+tcp://dcr.suprnova.cc:3252 -dwal username.worker2 -dpsw x And it seems everything works well below.... Just 1x GPU on my work PC, PowerColor Radeon rx580 (8GB). I'm just starting to learn about mining with one card above. ╔════════════════════════════════════════════════════════════════╗ ║ Claymore's Dual ETH + DCR/SC/LBC/PASC GPU Miner v10.0 ║ ╚════════════════════════════════════════════════════════════════╝
ETH: 1 pool is specified Main Ethereum pool is eth.suprnova.cc:5005 DCR: 1 pool is specified Main Decred pool is dcr.suprnova.cc:3252 At least 16 GB of Virtual Memory is required for multi-GPU systems Make sure you defined GPU_MAX_ALLOC_PERCENT 100 Be careful with overclocking, use default clocks for first tests Press "s" for current statistics, "0".."9" to turn on/off cards, "r" to reload pools, "e" or "d" to select current pool OpenCL initializing...
AMD Cards available: 1 GPU #0: Ellesmere, 8192 MB available, 36 compute units GPU #0 recognized as Radeon RX 480/580 POOL/SOLO version GPU #0: algorithm ASM No NVIDIA CUDA GPUs detected. Total cards: 1 DUAL MINING MODE ENABLED: ETHEREUM+DECRED ETH: eth-proxy stratum mode "-allpools" option is set, default pools can be used for devfee, check "Readme" file for details. Watchdog enabled Remote management (READ-ONLY MODE) is enabled on port 3333
ETH: Stratum - connecting to 'eth.suprnova.cc' <149.202.76.194> port 5005 DCR: Stratum - connecting to 'dcr.suprnova.cc' <217.182.138.167> port 3252 ETH: Stratum - Connected (eth.suprnova.cc:5005) DCR: Stratum - Connected (dcr.suprnova.cc:3252) ETH: Authorized Setting DAG epoch #153... DCR: Authorized Setting DAG epoch #153 for GPU0 Create GPU buffer for GPU0 GPU0 DAG creation time - 5608 ms Setting DAG epoch #153 for GPU0 done GPU0 t=60C fan=31% DCR: 11/25/17-18:59:00 - New job from dcr.suprnova.cc:3252 DCR: 11/25/17-18:59:15 - New job from dcr.suprnova.cc:3252 GPU0 t=67C fan=46% ...Anything else I can do to improve or tweak it with the batch file parameters? Does the port number looks correct? I read I need to use 5000 instead of 5005 somewhere. Also, the default command line shown in suprnova.cc (below) is without the "stratrum" pre-fix, but I got lots of authorisation errors without it. ethdcrminer64.exe -epool eth.suprnova.cc:5000 -ewal username.worker1 -epsw x -esm 3 -dpool dcr.suprnova.cc:3252 -dwal username.worker2 -dpsw x -allpools 1BTW, I've also tried to mod my GPU BIOS, copying memory lane 1750 to 2000 using Bios editor/ATIwinflash, that's all. The hash rate still sucks at 20-24MHs, but maybe because I'm also using it as my work PC and connecting a monitor to the GPU for extra screens. These are the few questions I have so far, thanks in advance for any tips! Hans
|
|
|
|
kkourmousis
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 119
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 12:06:00 PM |
|
Guys, what are you dual mining at the moment?
I have always been dual mining Decred Not saying it"s the best choice, but it's my choice
|
Buy me a souvlaki: ETH: 0x22D1C05F89dbe036aABFFEc197949E635903C6FA BTC: 1FHwEyiCqUTpauGfvPg5czMYoWMKqYGBWx
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 12:46:20 PM |
|
v10.2:
- fixed critical issues in remote management feature (attacker could crash miner even in read-only mode). - now miner supports up to #299 epoch. - in rare cases ADL API calls can hang, now watchdog checks it as well. - improved "-minspeed" option, check readme for details. - added "miner_getstat2" command to remote management, check "API.txt" for details. - EthMan: added detailed stats mode in main window. - a few minor improvements in both miner and EthMan.
|
|
|
|
dwdhu
Newbie
Offline
Activity: 37
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 01:19:12 PM |
|
Hi, please submit your new hashrates to gpustats.com! https://gpustats.com Thank you!
|
|
|
|
davescream
Newbie
Offline
Activity: 50
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 01:36:10 PM |
|
Latest version is v10.2: - added "miner_getstat2" command to remote management, check "API.txt" for details.
- ETH accepted shares for every GPU. - ETH rejected shares for every GPU. - ETH invalid shares for every GPU. - DCR accepted shares for every GPU. - DCR rejected shares for every GPU. - DCR invalid shares for every GPU.
Claymore thank you so much for that!!! Good that you include this not only in json queries, but http://ip:3333 web requests too.
|
|
|
|
digimonx
Newbie
Offline
Activity: 4
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 02:09:22 PM |
|
v10.2:
- fixed critical issues in remote management feature (attacker could crash miner even in read-only mode). - now miner supports up to #299 epoch. - in rare cases ADL API calls can hang, now watchdog checks it as well. - improved "-minspeed" option, check readme for details. - added "miner_getstat2" command to remote management, check "API.txt" for details. - EthMan: added detailed stats mode in main window. - a few minor improvements in both miner and EthMan.
I can download "Claymore's Dual Ethereum+Decred_Siacoin_Lbry_Pasca...v10.1 - Catalyst 15.12-17.x - CUDA 8.0_7.5_6.5.zip" from google drive without any issues, but my Windows Defender deletes "Claymore's Dual Ethereum+Decred_Siacoin_Lbry_Pasca...v10.2 - Catalyst 15.12-17.x - CUDA 8.0_7.5_6.5.zip" as soon as it is downloaded with "This file contained a virus and was deleted". What is different in v10.2 that causes this issue?
|
|
|
|
leonix007
Sr. Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 1008
Merit: 297
Grow with community
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 03:47:42 PM |
|
v10.2:
- fixed critical issues in remote management feature (attacker could crash miner even in read-only mode). - now miner supports up to #299 epoch. - in rare cases ADL API calls can hang, now watchdog checks it as well. - improved "-minspeed" option, check readme for details. - added "miner_getstat2" command to remote management, check "API.txt" for details. - EthMan: added detailed stats mode in main window. - a few minor improvements in both miner and EthMan.
I can download "Claymore's Dual Ethereum+Decred_Siacoin_Lbry_Pasca...v10.1 - Catalyst 15.12-17.x - CUDA 8.0_7.5_6.5.zip" from google drive without any issues, but my Windows Defender deletes "Claymore's Dual Ethereum+Decred_Siacoin_Lbry_Pasca...v10.2 - Catalyst 15.12-17.x - CUDA 8.0_7.5_6.5.zip" as soon as it is downloaded with "This file contained a virus and was deleted". What is different in v10.2 that causes this issue? It's normal, some AV's and windows defender included will detect this as virus, just look at your windows settings and firewall to exclude the claymore exe or the entire directory for exemptions.
|
|
|
|
xeridea
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 04:55:57 PM |
|
v10.2:
- fixed critical issues in remote management feature (attacker could crash miner even in read-only mode). - now miner supports up to #299 epoch. - in rare cases ADL API calls can hang, now watchdog checks it as well. - improved "-minspeed" option, check readme for details. - added "miner_getstat2" command to remote management, check "API.txt" for details. - EthMan: added detailed stats mode in main window. - a few minor improvements in both miner and EthMan.
Thanks for making great miners and good updates. Another feature request, can you make ethman show total hashrate per algorithm? Have some doing Eth, some doing XMR. Currently my hack is run a second instance of RM and only have XMR rigs on it. No rush, I know you are busy with multiple miners.
|
Profitability over time charts for many GPUs - http://xeridea.us/chartsBTC: bc1qr2xwjwfmjn43zhrlp6pn7vwdjrjnv5z0anhjhn LTC: LXDm6sR4dkyqtEWfUbPumMnVEiUFQvxSbZ Eth: 0x44cCe2cf90C8FEE4C9e4338Ae7049913D4F6fC24
|
|
|
dragonmike
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 05:08:26 PM |
|
Pretty cool site, nicely done. I've uploaded my nvidia rig stats for Zcoin. Might add more results to enrich the database a little. You should create a separate thread to promote it, actually.
|
|
|
|
Delija93
Newbie
Offline
Activity: 4
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 09:21:29 PM |
|
Hey, please help.. I have radeon 580 8gb.. i start to mine with 21,5 mh/s, after 3days 21mh/s, after 2-3 days 20,800 mh/s, now 20,260 mh/s ? Why i lose Mh/s? Sorry for my bad English.
|
|
|
|
|
Delija93
Newbie
Offline
Activity: 4
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2017, 10:39:41 PM |
|
Really O.o My friend instal drivers for my pc i don't know which.. To download and install this driver my gpu be better?
|
|
|
|
|
leonix007
Sr. Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 1008
Merit: 297
Grow with community
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 26, 2017, 07:49:20 AM |
|
Driver Alone can't reached the 29-30mhs hashrate, you need to mod your GPU's in order to achieve this, a lot of guides out there, example below posted by Mattthev. you have to at least checked what type of memory you had and proper timings. https://bitcointalk.org/index.php?topic=1954245.0
|
|
|
|
Delija93
Newbie
Offline
Activity: 4
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 26, 2017, 11:06:05 AM |
|
Really O.o My friend instal drivers for my pc i don't know which.. To download and install this driver my gpu be better? Yes, AMD has released a unique driver to solve this DAG problem. Follow link to download: My CARD is ASUS RADEON RX580 8GB OC Edition.. How much Mhs is that card? I don't know how to delete old driver and instal this one -_- http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx Driver Alone can't reached the 29-30mhs hashrate, you need to mod your GPU's in order to achieve this, a lot of guides out there, example below posted by Mattthev. you have to at least checked what type of memory you had and proper timings. https://bitcointalk.org/index.php?topic=1954245.0
|
|
|
|
|