Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[ildotoress]

Thanks for the details, hopefully tomorrow I have some time to try it out.

What about the fan RPM, has anyone made MSI AB work at least for fan control in Win 10 1709 (FCU) with latest official AM driver (11.3)?

[thx333]

Hello, in this moment I use 10.0 Version
Better upgrade to 10.2?

[Swiped]

I have 5x RX480 (Saphhire Nitro +) with Blockchain drivers and custom BIOS. I'm limited to 1000W power.  I'm currently mining ETH + LBRY but I have some wierd errors. GPU stops every few minutes and then starts again... I tryed lowering dcri but no help.
Now my settings are:

Clock: 1050
Voltage: 950
Memory: 2080
voltage: 950

Can you tell me what settings on GPU do you use for this combination?

I run the same set up to the following numbers:


Clock: 1160
Voltage: 900
Memory: 2020
Voltage: 920
Powlim: -10

I get 28-29 Mhs with this setting and run my machines at 1000W with 6 cards.
Good luck

[Ryuh]

Guys i have a problem with the miner and cant figure what is causing it exactly.
On my personal PC i have one nvidia 1070 for testing purposes. When i run Claymore Miner there, the whole computer start to work really slow.
The mining is fine, there is no problem there, but i can barely use the computer for anything else.
Its Windows 7 pro 64 bit, i7 2500k, 16 gb ram and SSD samsung 840 pro. Its a pretty decent computer.

On all of my rigs which have the cheapest processors possible, running Claymore's Miner is not problem for the computer. It's not noticeable at all.
You can browse the internet or whatever. The have Windows 10 pro 64 bit.

So tell me what you think, is this the OS difference thing? Or is it something else?
Please help!

[dexterop]

I only able to get 8 MH/s ETH with my Gigabyte GTX 970 regardless the miner I use. And every time I start mining I get "PerfCap Reason:VRel" in GPU-Z while the "Power Consumption" is around 45% TDP. Most people get from 14 to 23 MH/s on GTX 970
Windows 7 64 bit sp1
miner the latest version
NVidia Drivers 388

[Call_Me_Bambi]

Hi!

my problem is very strange and i cant find a solution to it. The miner starts up great checks my Graphics Card and says all is well. R9 270 btw ... then it starts mining the GPU goes to 100% BUT Core and Memory clock stay at 300 MHz instead of 1400 which is defined in the card settings .. so the card starts but only in low power mode how do i get it to work correctly???

This may not fix the problem but ensure that the swap file is at least 16GB . Some more information on your setup would also help, such as OS, Drivers used and miner config.

[g0lddi99er]

Hey guys,

Just a quick question to see if any of you came across such issue:

After the latest Windows 10 Pro upgrade I started having this wierd issue with one of my cards (MSI RX580 8GB) in PCIE_16x slot 0 (ASUS Z270-P). The miner would get stuck at POOL/SOLO output and mining would never start. I tried a few things and noticed that when I disabled GPU 0 (using the -di argument) the remaining cards would start mining without any issues. I suspected some issue with the card, raiser or the motherboard. I did some troubleshooting and noticed that any card inserted in that PCIE slot was having the issues so that ruled out the raisers or cards. Provided that the only change made was the windows upgrade, I tried to download and install latest chipset and ME drivers, latest BIOS and did a fresh install of the blockchain drivers (using DDU). None of that helped so I thought the slot is faulty or something but then I noticed something very strange...when I plug in a monitor into the impacted card, everything started working (or at least for the past 48 hours). The monitor does not even need to be turned on as long as the DVI cable is plugged in on both ends.

Has anybody experienced such issue or am I going crazy here 😂

[Nazgu1]

So, I have a 980ti that gives me a hashrate of a little over 21 MHz/s when running in benchmark mode. But once I start actual mining using Nanopool, it drops to ~14 MHz/s, which is roughly a 33% drop. Now, I know that one should expect a certain drop in performance (e.g. 1% pool fee +1% miner fee), but a drop of 33% is too much!

Any reasons for that?

[BoostOrDie]

Hey guys,

Just a quick question to see if any of you came across such issue:

After the latest Windows 10 Pro upgrade I started having this wierd issue with one of my cards (MSI RX580 8GB)....

Has anybody experienced such issue or am I going crazy here 😂

Return question - WHY?
Why upgrade or update windows? especialy on mining rig? It works good - leave it as it is!
Updates wont give you hasgrate increase. Honestly speaking you wont see any difference at all. You have about 70% of seeng new problems instead of any improvements..


Trying Clay 10.2 will see how it goes. 10.1 was highly unstable and unusable..

So, I have a 980ti that gives me a hashrate of a little over 21 MHz/s when running in benchmark mode. But once I start actual mining using Nanopool, it drops to ~14 MHz/s, which is roughly a 33% drop. Now, I know that one should expect a certain drop in performance (e.g. 1% pool fee +1% miner fee), but a drop of 33% is too much!

Any reasons for that?

Benchmark is not the same as real minig. it will never have the same result.
Also as far as I remember you have to specify difficulty or epoch for benchmark.
In your case it looks like you are starting benchmark with a lower difficulty than it is at the moment in real mining

[lankyman]

I have 3 AMD GPUs and for some reason i only get half speed on my 3rd GPU.
Anybody have this issue ?
Ive tried different motherboard windows 7 pro 64bit.

[leonix007]

Guys i have a problem with the miner and cant figure what is causing it exactly.
On my personal PC i have one nvidia 1070 for testing purposes. When i run Claymore Miner there, the whole computer start to work really slow.
The mining is fine, there is no problem there, but i can barely use the computer for anything else.
Its Windows 7 pro 64 bit, i7 2500k, 16 gb ram and SSD samsung 840 pro. Its a pretty decent computer.

On all of my rigs which have the cheapest processors possible, running Claymore's Miner is not problem for the computer. It's not noticeable at all.
You can browse the internet or whatever. The have Windows 10 pro 64 bit.

So tell me what you think, is this the OS difference thing? Or is it something else?
Please help!

You may look at your task manager to check your cpu, memory, hdd utilization, you may find application or processes that may caused it, you may also kill those unwanted process if there's any

I have 3 AMD GPUs and for some reason i only get half speed on my 3rd GPU.
Anybody have this issue ?
Ive tried different motherboard windows 7 pro 64bit.

check the other GPU if has high temps? is this a modded? you may check also your risers

[kkourmousis]

Trying Clay 10.2 will see how it goes. 10.1 was highly unstable and unusable..

A clean Windows install+FCU, AMD 17.11.2 and Claymore's v.10.1 is the most stable setup I have ever had. 1 month now with no problems at all

Btw, 17.11.4 got released, did anyone try it out?

[okane818]

Hello Guys,
I want to go mining with ELLAISM coin, I need your help to setup my GTX 1080,
Can anyone share the configuration to connect with the server.

Thanks

[leonix007]

Hello Guys,
I want to go mining with ELLAISM coin, I need your help to setup my GTX 1080,
Can anyone share the configuration to connect with the server.

Thanks

This is an Ethash Algo, same configuration with Ethereum ETH and ETC, you may use the pool below for mining.

https://ellaism.org/mining/

that coin is worth a try I guess, might be helpful if you let us know if this is profitable.

[rramires]

I love Decred.

Tip:
I mine Decred using Claymore's with Ethereum, sell ETH and investing in PoS mining that yield about 1.8% every 28 days:
https://docs.decred.org/mining/proof-of-stake

[EmilioMann]

I love Decred.

Tip:
I mine Decred using Claymore's with Ethereum, seeing ETH and investing in PoS mining that yield about 1.8% every 28 days:
https://docs.decred.org/mining/proof-of-stake

I also do that and I'm getting richer and richer.
Decred my lov 

[BoostOrDie]

Trying Clay 10.2 will see how it goes. 10.1 was highly unstable and unusable..

A clean Windows install+FCU, AMD 17.11.2 and Claymore's v.10.1 is the most stable setup I have ever had. 1 month now with no problems at all

Btw, 17.11.4 got released, did anyone try it out?

Im on GTX1060's

[Ryuh]

You may look at your task manager to check your cpu, memory, hdd utilization, you may find application or processes that may caused it, you may also kill those unwanted process if there's any

Yeah, i already did that, the only thing that works is killing the miner task.

[AlainC]

Hi, it seems @claymore repo on github is disabled
https://github.com/nanopool/Claymore-Dual-Miner

https://www.reddit.com/r/EtherMining/comments/7gmngy/claymore_dual_miner_repository_has_been_disabled/
Hope this helps.

[P00P135]

Hi, it seems @claymore repo on github is disabled
https://github.com/nanopool/Claymore-Dual-Miner

https://www.reddit.com/r/EtherMining/comments/7gmngy/claymore_dual_miner_repository_has_been_disabled/
Hope this helps.

That is nanopool its nothing to worry about or even use.  Just get it directly from the OP.