Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[ps_jb]

02:27:22:161   11f0   ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166   11f0    DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171   11f0    DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s

Your hashrate is very impressive for rx 480 in dual mining!

Again - could you please share the card stock settings and you Wattman parameters?

[1714672221]

1714672221

[adamvp]

Ethman issue:
Few ours after starting all rigs went red (indeed rigs work, but EthMan doesn't show it)
and I have :

Code:

Access violation at adress 00000000. Read of adress 00000000

error when I try to close the Ethman...

[akaloith]

can you please tell me mhash/sec for eth only on gtx 1060 + gtx 1070 for last version claymore ?

[thevictimofuktyranny]

v6.4:

- added "-etha 2" option value for gpu-pro Linux drivers.
- fixed issue with a bit lower mining speed of previous version (AMD cards).
- Improved speed by about 3% for NVIDIA 10xx cards in Windows 10 (CUDA 8.0 build).
- NVIDIA: added build with CUDA 8.0, it is default now, there are also CUDA 6.5 and 7.5 builds in separate folders.
- NVIDIA: added temperatures/fans monitoring. Note that fans management is not available, only monitoring is possible.
- EthMan now shows "off" or "stopped" status for disabled/stopped cards in detailed hashrate stats.

Great work, again Claymore

[Naimon]

OP updated with new info:

NVIDIA DRIVERS:
9xx cards in Windows 7 x64: just use latest/recent drivers from Nvidia website (for example, 368.81). Note that latest 372.54 is slower than 368.81.
9xx cards in Windows 10 x64: you have to use old drivers (for example, 352.xx) and miner built for cuda6.5.
10xx cards in Windows 7 x64: just use latest 372.54 drivers from Nvidia website.
10xx cards in Windows 10 x64: just use latest 372.54 drivers from Nvidia website, note that you must have Win10 Anniversary update.

For what it's worth, I'm noticing slightly faster speeds (about 0.1MH/s to 0.2MH/s per card) on my 1070s using Windows 10 x64 v369.09.  Anyone else notice this?

[alevlaslo]

Claymore

Monero good profit now but old miners is too cool, maybe need update there?

[peoples]

About ADL in GPU-PRO drivers, just found a beautiful answer:

https://bugs.freedesktop.org/show_bug.cgi?id=96786

...
ADL is not supported in the amdgpu-pro driver.  The same functionality can be accessed via standard Linux interfaces (e.g., hwmon for temperature and fan control, sysfs for clock control, etc..
...

So AMD decided not to worry about ADL support in new drivers for Linux. Excellent solution.

Hey, thanks for 6.3 release. Linux version looks smooth so far, no more VM fault errors.
One of your corefeatures in my opinion is the selectiv shutdown of cards in case of overheat, maybe you can implement this also with the new AMDGPU driver ?

You can query the temperature of the cards from: /sys/class/hwmon/hwmonX/temp1_input
To identify the cards that are useing amdgpu driver you can query the /sys/class/hwmon/hwmonX/name class ?

BTW: Overclocking is done by the keys  /sys/class/hwmon/hwmon1/pp_mclk_od (Memory Clock)  and /sys/class/hwmon/hwmon1/pp_sclk_od GPU Clock. +1 changes value by 20.

Just to clarify
For temperature just get it from /sys/class/hwmon/hwmon/hwmonX/temp1_unit, the result must divide by 1000 to get the correct celcius
and we can check whether the hardware is amdgpu or not by checking /sys/class/hwmon/hwmonX/name , If it is amdgpu then it's the right one.

Above file can be access without root.

For overclocking and setup fan speed currently the user has to be root, even sudo is not working. Maybe the user need to be included in specific group first. I leave this to the linux user, since we only need to set it once. Note that when using root user the path is no longer /sys/class/hwmon but change to /sys/class/drm/cardX/device/hwmon

For memory +1 increase 20Mhz, for core clock +1 increase 12MHz. To get the highest one use -1 instead.

Maybe for now just include the temperature so the watchdog can protect the miner in case something happen.

@claymore
what do you think about this ?

@claymore any plans for temperature under linux ?

[relm9]

I happened to give the Pascal Titan X a try with this,

Results at stock, ~30.8 Mh/s in ETH and 300 Mh/s in DCR

Bumped up memory to +400 and got

34 Mh/s in ETH and 331 Mh/s in DCR

Definitely not a cost effective card but thought I'd post the numbers if anyone was curious. This was done in Windows 10 with the v6.4 build btw

[LeChuckDE]

could you pls share your json syntax for the connection proccess  ?

{
  "id": 1,
   "worker": "RIG_ID",
  "jsonrpc": "2.0",
  "method": "eth_submitLogin",
  "params": ["0xb85150eb365e7df0941f0cf08235f987ba91506a"]
}

Looks like not working... with my pools

[QuintLeo]

I happened to give the Pascal Titan X a try with this,

Results at stock, ~30.8 Mh/s in ETH and 300 Mh/s in DCR

Bumped up memory to +400 and got

34 Mh/s in ETH and 331 Mh/s in DCR

Definitely not a cost effective card but thought I'd post the numbers if anyone was curious. This was done in Windows 10 with the v6.4 build btw

 No real shock there, but good to have hard numbers to be sure.

[ioglnx]

The new version often hung and stops working. Usually i do 20-28 Shares per H with my 1080 on Windows 10 x64 (1607) + 372.54.
It just recognizes it (assume the watchdog) when i press a key in the cmd and prints out that it detected a hung process and restarts...this should happen automatically if and it shouldn't happen anyway.
Also the memory runs below just at 75% if the max. speed when your miner is running..something wrong.
The previous version was running 1 week with the same config without any problem.

Some ideas why this happens?

Thanks in advance

[xeridea]

I happened to give the Pascal Titan X a try with this,

Results at stock, ~30.8 Mh/s in ETH and 300 Mh/s in DCR

Bumped up memory to +400 and got

34 Mh/s in ETH and 331 Mh/s in DCR

Definitely not a cost effective card but thought I'd post the numbers if anyone was curious. This was done in Windows 10 with the v6.4 build btw

Eth sounds about right, DCR seems low, did you change dcri?

[relm9]

I happened to give the Pascal Titan X a try with this,

Results at stock, ~30.8 Mh/s in ETH and 300 Mh/s in DCR

Bumped up memory to +400 and got

34 Mh/s in ETH and 331 Mh/s in DCR

Definitely not a cost effective card but thought I'd post the numbers if anyone was curious. This was done in Windows 10 with the v6.4 build btw

Eth sounds about right, DCR seems low, did you change dcri?

Ah, it was at default.

I tried -dcri 70 just now with my memory OC (+400), and got 775 Mh/s. Much better. ETH hashrate dropped to 33 with the DCR intensity raised.

[fr4nkthetank]

im getting quite a bit of incorrect shares with the latest versions.  About 1% in some cases, compared to 0% before.  running 6.4.  Should I run to a version prior to nvidia support ?  edit: could be nicehash too, idk, but these are incorrect shares when pressing >s<

[vapourminer]

[DAG fail on single r9 380 2 GB on ubuntu 15.10]

Miner creates DAG on every card. No transfers. If you get error it means that OpenCL cannot allocate enough buffer. Why? I don't know. Perhaps OS allocated some memory for itself. Or OpenCL drivers don't like your configuration for some reason and therefore don't allow to allocate max memory. Unfortunately I don't know drivers logic about max memory limits calculation, I only know that is not simple and that's the reason of many problems.

thats kinda what i thought too, which is why i shut down xorg. cdm reported vram went from 1.8 gb to 2 gb so just running the gui takes 256 mb vram. ill pick away at it, if i figure it out ill let you know.

ah well the evga will be here soon. just figured i would give the 380 alone a run till then.

got it running.

told ubuntu to not load the GUI and go straight to terminal. basically by uninstalling lighdm which is the GUI. that plus the environmental variables and now the 380 runs by itself.

i would imagine those who run the server additions of ubuntu would not run into this on 2 gig cards that also have a GUI to contend with. just seems faintly rediculous to run a computer in pure text mode when it has crazy powerful graphics cards. feels like im back in CP/M..

[calculatorduck]

On my GTX 1070 the 6.4 build is actually slightly slower with CUDA 8 which is strange because Genoil's miner with CUDA 8 is notably faster.

version 6.2 (CUDA 7.5) 26.6 ETH 710 SIA

version 6.4 (CUDA 8 ) 26.1 ETH 685 SIA

This is Win10 anniv with the latest nvidia drivers

[Claymore]

On my GTX 1070 the 6.4 build is actually slightly slower with CUDA 8 which is strange because Genoil's miner with CUDA 8 is notably faster.

version 6.2 (CUDA 7.5) 26.6 ETH 710 SIA

version 6.4 (CUDA 8 ) 26.1 ETH 685 SIA

This is Win10 anniv with the latest nvidia drivers

You can use v6.4 CUDA 7.5 if you don't like speed of CUDA 8.0. Speed depends on windows&drivers&gpu so I include cuda 6.5, 7.5 and 8.0 builds, you can select the best for you.

[kilmarnock]

I tried v. 6.4 on Ubuntu 16.04 64 bit, driver is amdgpu-pro_16.30.03-315407, kernel is 4.4.0-34-generic

the output is

Code:

./ethdcrminer64 -epool coinotron.com:3344 -ewal username.3 -esm 2 -epsw 3 -allpools 1 -mode 1 -etha 2

ͻ
�        Claymore's Dual ETH + DCR/SC GPU Miner v6.4 Beta        �
ͼ

ETH: 1 pool is specified
Main Ethereum pool is coinotron.com:3344
segmentation fault

Isn't this the target platform? Can I help debugging?
(genoil 110 does mine. radeon 480)
Felix

[Claymore]

I tried v. 6.4 on Ubuntu 16.04 64 bit, driver is amdgpu-pro_16.30.03-315407, kernel is 4.4.0-34-generic

the output is

Code:

./ethdcrminer64 -epool coinotron.com:3344 -ewal username.3 -esm 2 -epsw 3 -allpools 1 -mode 1 -etha 2
ͻ
�        Claymore's Dual ETH + DCR/SC GPU Miner v6.4 Beta        �
ͼ
ETH: 1 pool is specified
Main Ethereum pool is coinotron.com:3344
segmentation fault

Isn't this the target platform? Can I help debugging?
(genoil 110 does mine. radeon 480)
Felix

Just tried same configuration - it works fine for me.
PM me the full log.

[kridlak]

Hello.
For me 6.3 is stable, with tiny speed lost.
But 6.4 unstable. Fault every  1-3 hour with OpenCL error.
Ubuntu 14.04.5 LTS, kernel 4.2.0-27, fglrx 15.12 installed from source at amd site, two firm saphire r9 390x2 and gigabyte r9 390x2