|
bytiges
|
|
October 10, 2017, 04:22:27 PM |
|
So, is your girlfriend mining on another pool ? Which one ? How are earnings ?
|
|
|
|
Tai_Pan
|
|
October 10, 2017, 06:18:15 PM |
|
Can someone who updated the firmware post here a screen shot from the dashboard's "system \ overview" please?
Thank you.
You doubt about people do this upgrade ? It seems safe to do since is a official release. Here is your screenshot, IP is hyde. Thanks. I don't doubt anyone, I just wanted to see the numbers / the versions and so on
|
|
|
|
VoskCoin
|
|
October 10, 2017, 07:03:42 PM |
|
So, is your girlfriend mining on another pool ? Which one ? How are earnings ? Personally I / we are worried about the rising diff so unfortunately we decided to sell the D3's - I think the outlook is grim O_O
|
|
|
|
Dopert
|
|
October 10, 2017, 08:22:56 PM |
|
Yup, like said, 2 bullets in the chamber, but i purchashed 4x for november batch. Presold 3x and get 0.45 deposit. Hope he will make no trouble if diffc. Gose up more. I hold 1 to play, maybe mine a little x11 coin for the hold and pray
|
|
|
|
RealKariverson
|
|
October 10, 2017, 10:21:44 PM |
|
Can someone who updated the firmware post here a screen shot from the dashboard's "system \ overview" please?
Thank you.
What they did with my l3+ back in July was an email some days before shipping for shipping confirmation. Then an email that it shipped with a commercial invoice attached. About VAT, when it arrives, you have to talk to your customs office and/or the courier service. Has anyone gotten shipping confirmation for October 15th?
|
|
|
|
CryptoDj
Newbie
Offline
Activity: 12
Merit: 0
|
|
October 10, 2017, 11:01:46 PM |
|
Hello Guys, someone can recommend me a PSU for the D3 since I could not buy mine in bitmain with my order.
|
|
|
|
shaninium
|
|
October 11, 2017, 12:30:08 AM |
|
Does anyone have problem when some miners losing 3rd board and hashing 10-11 Ghs? This happens on many D3 miners, not just on one. Miners works on default settings, temperatures are good, max board temperatures are 65-70C. After I restart D3, all boards working normally again for some time. Is there some firmware upgrade for this problem, anyone have solution for this? D3 is not stable miner at all. L3+ is a lot better device.
I have same problem here even after firmware update unless there's been a new update in past week.
|
|
|
|
kodokbuduk
|
|
October 11, 2017, 03:22:29 AM |
|
Does anyone have problem when some miners losing 3rd board and hashing 10-11 Ghs? This happens on many D3 miners, not just on one. Miners works on default settings, temperatures are good, max board temperatures are 65-70C. After I restart D3, all boards working normally again for some time. Is there some firmware upgrade for this problem, anyone have solution for this? D3 is not stable miner at all. L3+ is a lot better device.
got the same problem with mine. Would appreciate some infos. Yea same. Anyone upgraded firmware and solve the problem?
|
|
|
|
kodokbuduk
|
|
October 11, 2017, 03:23:54 AM |
|
Can someone who updated the firmware post here a screen shot from the dashboard's "system \ overview" please?
Thank you.
You doubt about people do this upgrade ? It seems safe to do since is a official release. Here is your screenshot, IP is hyde. Thanks. I don't doubt anyone, I just wanted to see the numbers / the versions and so on my hardware ver 1.0.0.6
|
|
|
|
digital$
Member
Offline
Activity: 287
Merit: 18
|
|
October 11, 2017, 03:59:53 AM |
|
hoping this is a firmware issue...perhaps bitmain are aware of the problem hence upgrade/update. thanks for posting and hope its resolved soon
|
|
|
|
AriesIV10
Legendary
Offline
Activity: 1260
Merit: 1006
Mine for a Bit
|
|
October 11, 2017, 06:38:19 AM |
|
Hello Guys, someone can recommend me a PSU for the D3 since I could not buy mine in bitmain with my order.
This is where I buy some of my PSUs: www.parallelminer.comThey are reliable and have a good lead-time.
|
|
|
|
Maicol792
Legendary
Offline
Activity: 1260
Merit: 1010
|
|
October 11, 2017, 09:20:36 AM |
|
hi, anyone mining dash in solo on nicehash? ... what is the best _diff value?? for D3 miner? thanks
|
|
|
|
lashatatu
|
|
October 11, 2017, 09:37:32 AM |
|
can this be used to mine any coin with any algo?
any coin on x11 algo
|
|
|
|
micairvas
|
|
October 11, 2017, 10:02:54 AM |
|
Does anyone have problem when some miners losing 3rd board and hashing 10-11 Ghs? This happens on many D3 miners, not just on one. Miners works on default settings, temperatures are good, max board temperatures are 65-70C. After I restart D3, all boards working normally again for some time. Is there some firmware upgrade for this problem, anyone have solution for this? D3 is not stable miner at all. L3+ is a lot better device.
got the same problem with mine. Would appreciate some infos. I think is a common issue ... I have this problem to, it happen sometime after some days. I update firmware, reset hardware etc ... Nothing fix this issue, he just happen. Other problem i get, on one of my D3, on board get error on launch like they cant reach correct submitted work, it chain 40-50 HW error and show some xxx on this board. After 1 minute, board launch like is ok, remove all xxx and accept submitted work. Tried this firmware? https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E
|
|
|
|
thiec
|
|
October 11, 2017, 12:05:52 PM |
|
Does anyone have problem when some miners losing 3rd board and hashing 10-11 Ghs? This happens on many D3 miners, not just on one. Miners works on default settings, temperatures are good, max board temperatures are 65-70C. After I restart D3, all boards working normally again for some time. Is there some firmware upgrade for this problem, anyone have solution for this? D3 is not stable miner at all. L3+ is a lot better device.
got the same problem with mine. Would appreciate some infos. I think is a common issue ... I have this problem to, it happen sometime after some days. I update firmware, reset hardware etc ... Nothing fix this issue, he just happen. Other problem i get, on one of my D3, on board get error on launch like they cant reach correct submitted work, it chain 40-50 HW error and show some xxx on this board. After 1 minute, board launch like is ok, remove all xxx and accept submitted work. Tried this firmware? https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066EIs it upgrading or changing firmware without bitmain's permission will void the warranty?
|
|
|
|
digital$
Member
Offline
Activity: 287
Merit: 18
|
|
October 11, 2017, 12:21:04 PM |
|
Does anyone have problem when some miners losing 3rd board and hashing 10-11 Ghs? This happens on many D3 miners, not just on one. Miners works on default settings, temperatures are good, max board temperatures are 65-70C. After I restart D3, all boards working normally again for some time. Is there some firmware upgrade for this problem, anyone have solution for this? D3 is not stable miner at all. L3+ is a lot better device.
got the same problem with mine. Would appreciate some infos. I think is a common issue ... I have this problem to, it happen sometime after some days. I update firmware, reset hardware etc ... Nothing fix this issue, he just happen. Other problem i get, on one of my D3, on board get error on launch like they cant reach correct submitted work, it chain 40-50 HW error and show some xxx on this board. After 1 minute, board launch like is ok, remove all xxx and accept submitted work. Tried this firmware? https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066EIs it upgrading or changing firmware without bitmain's permission will void the warranty? any firmware update has to be "bitmain" firmware..ie. they release new version and you update(then all is good) only firmware by bitmain can be used if under warranty. upgrade?? any other means of upgrade will void warranty
|
|
|
|
mdude77
Legendary
Offline
Activity: 1540
Merit: 1001
|
|
October 11, 2017, 12:24:25 PM |
|
Does anyone have problem when some miners losing 3rd board and hashing 10-11 Ghs? This happens on many D3 miners, not just on one. Miners works on default settings, temperatures are good, max board temperatures are 65-70C. After I restart D3, all boards working normally again for some time. Is there some firmware upgrade for this problem, anyone have solution for this? D3 is not stable miner at all. L3+ is a lot better device.
It's always risky getting batch one items from Bitmain. They don't have a stellar reputation for the first batch working the greatest. M
|
I mine at Kano's Pool because it pays the best and is completely transparent! Come join me!
|
|
|
Mr_Snipes
|
|
October 11, 2017, 12:44:09 PM |
|
regarding these outages some of you have: i had it once as the ambient temp in the romm hit ~26C° Chiptemp was 70C° to 72C° when i had this issue. So i manually set the fan to 100% - had no problems since that fix.
|
|
|
|
BenRickert
|
|
October 11, 2017, 12:54:53 PM |
|
Hello Guys, someone can recommend me a PSU for the D3 since I could not buy mine in bitmain with my order.
This is where I buy some of my PSUs: www.parallelminer.comThey are reliable and have a good lead-time. This is an EXTREMELY USEFUL link. THANK YOU! Crypto Accepted.
|
|
|
|
|