T-Rex 0.26.8 ETHW, ETC (+dual mining) GPU miner

[EdgeOfSanity]

Can this dual mining mode be used with non-lhr cards? Are the hashrates higher?

[TheFreemancer]

Would be nice to have a low power consumption dual mining option.

3080 Ti is able to achieve 40 MH/s on ETH and 180 MH/s on ERGO at the same time but consuming 260 W.

3060 Ti can achieve 20 MH/s on ETH and 90 MH/s on ERGO at the same time but consuming 140 W.


I would say locking the core clock is a very bad idea using this new setting, open GPU-Z and under sensors you can see the hit the voltage regulators are taking if the core is locked.
If the core clock can fluctuate there is a minor mV difference ~0.2mV at load cycles but it would cause less stress to the GPU.

The optimum solution would be if a stable load, voltage, wattage and clock speed could be possible if the miner send bogus or random empty calculations to the GPU between cycles.

Also be sure to keep an eye on your power consumption, specially if you own a 3090, the driver isn't able to fully control the power delivery and you can have the same situation as the game New World.

[Dr_Victor]

Are you kidding? ETH+ERGO on 3080 Ti = 6,1$, ETH only = 6,3. Where is the reason?

[UsingMyName]

Not getting full unlock with eth/rvn 3060 12gb v2-win 10. With LHR at 29 im at 15eth/11rvn.  Missing something probably...anyone know...Here is my batch:

 t-rex.exe -a ethash --lhr-algo kawpow -o stratum+tcp://us1.ethermine.org:14444 -u [wallet] -p x -w 3060eth --url2 stratum+tcp://stratum-ravencoin.flypool.org:13333 --user2 [wallet].3060Raven --pass2 x
pause



TDP 60%, 100% w/ core-500/+1250

I should be looking for approximately 15eth/35rvn?

[TheFreemancer]

Are you kidding? ETH+ERGO on 3080 Ti = 6,1$, ETH only = 6,3. Where is the reason?

I get that you have free electricity?

It's not possible to have 80 MH/s of ETH under 260w.

[philipma1957]

Can this dual mining mode be used with non-lhr cards? Are the hashrates higher?

I would love to know this answer.

[demkd]

LHR dual mining not working at all on my palit 3080ti, GPU constantly get locked and hasrhate drops down.
Waste of time, switched back at ETH mining at 80mhz.

[sxemini]

LHR dual mining not working at all on my palit 3080ti, GPU constantly get locked and hasrhate drops down.
Waste of time, switched back at ETH mining at 80mhz.

  waste of time? how much you wasted? 5min? You can do it better? So why no miner from you?

It is the first version so no hate to the devs, only love for their hard work.

[Mishmear]

Anyone had problems with 3060ti just locking instantly? If so and you managed to fix it let me know please 😁 everything i try its just locking.

Thankssss

[g_man_g]

Anyone had problems with 3060ti just locking instantly? If so and you managed to fix it let me know please 😁 everything i try its just locking.

Thankssss

Same issue on most of my 3060ti EVGA SC2. Only a few are unlocking even after 30 min run time.  Tried changing the LHR tune to 32 but no difference.  Just keeps stepping down until LHR 10, never unlocks.  On the cards that do unlock it's great. On bench testing rig with 1 or 2 cards no problem.  Having issues on 6 card and 12 card rigs.

[Kikbow]

Hello newbie miner here how can I tell if I have a LHR card
Below is my current setup
https://i.imgur.com/YE0Zc3W.png

[philipma1957]

Hello newbie miner here how can I tell if I have a LHR card
Below is my current setup

96 mh for 1 3080 is not lhr it is full power

96 is close to the max you can get with a 3080.

[Kikbow]

Hello newbie miner here how can I tell if I have a LHR card
Below is my current setup
https://i.imgur.com/YE0Zc3W.png

96 mh for 1 3080 is not lhr it is full power

96 is close to the max you can get with a 3080.

sick

[guytechie]

Not sure of this was answered, but is the new GPU order the same as how nvidia-smi reports it now?  Both Windows and Linux?

[tbearhere]

Not sure of this was answered, but is the new GPU order the same as how nvidia-smi reports it now?  Both Windows and Linux?

As far as I know yes. I'm going to test it now. 

[Rickirs]

I can't get my cards to follow fan temperature directive. These are couple of 1060 6G, I am using json config, have set it as :

Code:

"fan" : "t:65",

Launched miner with "sudo" but no effect.

Any insight ?

Anyone ?

[trexminer]

I can't get my cards to follow fan temperature directive. These are couple of 1060 6G, I am using json config, have set it as :

Code:

"fan" : "t:65",

Launched miner with "sudo" but no effect.

Any insight ?

Anyone ?

sudo? Fan control is a windows-only feature

[trexminer]

T-Rex 0.24.2

* ("autolykos2") Enable LHR unlock functionality
  See https://github.com/trexminer/T-Rex/wiki/LHR#ergo for more details

* ("ethash", "autolykos2") Add LHR unlock "auto-tune" functionality (see "--lhr-autotune-mode" in readme)
  Now the miner will try increasing "--lhr-tune" if it is stable at the current value, so you'll find out what the maximum LHR tune your cards can sustain without trying a lot of values manually.
  If you want the miner to stay at the LHR tune value you set yourself no matter what, use "--lhr-autotune-mode off".

* Add ETH+ZIL mining mode with an arbitrary ETH pool (not proxying through a ZIL pool)
  See ETH+ZIL "*.bat/*.sh" file in miner archive

* New parameter "--no-new-block-info" to stop "new block" messages appearing in miner console
* (WebUI) Update interface to handle dual mining mode (algo switch button in the top right corner)

Bug fixes:
* ("kawpow") Hashrate degradation in version 0.24.0 on some configurations

[simplemining]

Tbh, I hardly see any marginal improvement while using dual LHR mining method over solo LHR method.
Am I doing something wrong?)

[Divinity666]

T-Rex 0.24.2

* New parameter "--no-new-block-info" to stop "new block" messages appearing in miner console

God bless You for that!