GoRDoN-ChoU
Newbie
 Offline
Activity: 39
Merit: 0
|
 |
December 23, 2014, 11:04:31 AM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! |
|
|
|
|
|
|
|
|
|
Transactions must be included in a block to be properly completed. When you send a transaction, it is broadcast to miners. Miners can then optionally include it in their next blocks. Miners will be more inclined to include your transaction if it has a higher transaction fee.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
Newar
Legendary
Offline
Activity: 1358
Merit: 1000
https://gliph.me/hUF
|
|
December 23, 2014, 11:06:10 AM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell  PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? |
|
|
|
GoRDoN-ChoU
Newbie
Offline
Activity: 39
Merit: 0
|
|
December 23, 2014, 11:23:33 AM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W |
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 11:33:51 AM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy |
|
|
|
GoRDoN-ChoU
Newbie
Offline
Activity: 39
Merit: 0
|
|
December 23, 2014, 11:51:48 AM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy 1.all 288w but only use 230~270w report from ASIC stats 2.no (but cable that of the picture is) 3.I cant tell, maybe 10AWG or 9AWG 4.32C report from another working SP20 i don't wanna go RMA because i think the problem is on my plugs, if you give me a new one that is really not fair to you, i just want to keep this miner cover in warranty after i replaced the socket myself. |
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 12:11:54 PM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy 1.all 288w but only use 230~270w report from ASIC stats 2.no (but cable that of the picture is) 3.I cant tell, maybe 10AWG or 9AWG 4.32C report from another working SP20 i don't wanna go RMA because i think the problem is on my plugs, if you give me a new one that is really not fair to you, i just want to keep this miner cover in warranty after i replaced the socket myself. Indeed, it's most probably a problem with your cables. Use of improper cables voids the warranty of course. However, we want to investigate to be 100% sure. Out of 1,000s of SP20 we sold, this is the first reported instance. I'm offering you free RMA nevertheless, all we want is the PSU and cables. Guy |
|
|
|
|
Subw
|
|
December 23, 2014, 12:45:53 PM |
|
only see the wrong design from the very first SP20 . There should be a 8x PCI-E.
true. maxing out power rating for the socket is very wrong decision Please continue SP20 related technical discussions in our thread. The manufacture takes 20% margines over the 288 Watt rating. 1. Where 288W per one molex came from? 2. Why video card manufacturers use two molex sockets? High end GPUs consume ~275w max |
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 12:49:31 PM |
|
only see the wrong design from the very first SP20 . There should be a 8x PCI-E.
true. maxing out power rating for the socket is very wrong decision Please continue SP20 related technical discussions in our thread. The manufacture takes 20% margines over the 288 Watt rating. 1. Where 288W per one molex came from? 2. Why video card manufacturers use two molex sockets? High end GPUs consume ~275w max From the Molex connector manufacturer. |
|
|
|
GoRDoN-ChoU
Newbie
Offline
Activity: 39
Merit: 0
|
|
December 23, 2014, 01:07:19 PM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy 1.all 288w but only use 230~270w report from ASIC stats 2.no (but cable that of the picture is) 3.I cant tell, maybe 10AWG or 9AWG 4.32C report from another working SP20 i don't wanna go RMA because i think the problem is on my plugs, if you give me a new one that is really not fair to you, i just want to keep this miner cover in warranty after i replaced the socket myself. Indeed, it's most probably a problem with your cables. Use of improper cables voids the warranty of course. However, we want to investigate to be 100% sure. Out of 1,000s of SP20 we sold, this is the first reported instance. I'm offering you free RMA nevertheless, all we want is the PSU and cables. Guy but the PSU is my friend's, could you send it back to me after the testing? |
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 01:09:49 PM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy 1.all 288w but only use 230~270w report from ASIC stats 2.no (but cable that of the picture is) 3.I cant tell, maybe 10AWG or 9AWG 4.32C report from another working SP20 i don't wanna go RMA because i think the problem is on my plugs, if you give me a new one that is really not fair to you, i just want to keep this miner cover in warranty after i replaced the socket myself. Indeed, it's most probably a problem with your cables. Use of improper cables voids the warranty of course. However, we want to investigate to be 100% sure. Out of 1,000s of SP20 we sold, this is the first reported instance. I'm offering you free RMA nevertheless, all we want is the PSU and cables. Guy but the PSU is my friend's, could you send it back to me after the testing? Sure. |
|
|
|
GoRDoN-ChoU
Newbie
Offline
Activity: 39
Merit: 0
|
|
December 23, 2014, 01:15:12 PM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy 1.all 288w but only use 230~270w report from ASIC stats 2.no (but cable that of the picture is) 3.I cant tell, maybe 10AWG or 9AWG 4.32C report from another working SP20 i don't wanna go RMA because i think the problem is on my plugs, if you give me a new one that is really not fair to you, i just want to keep this miner cover in warranty after i replaced the socket myself. Indeed, it's most probably a problem with your cables. Use of improper cables voids the warranty of course. However, we want to investigate to be 100% sure. Out of 1,000s of SP20 we sold, this is the first reported instance. I'm offering you free RMA nevertheless, all we want is the PSU and cables. Guy but the PSU is my friend's, could you send it back to me after the testing? Sure. Thanks! information please |
|
|
|
|
|
raskul
|
|
December 23, 2014, 01:17:58 PM |
|
one single voluntary RMA in thousands of orders and SP-Tech competitors seem to be having a party about it. it's good that this community are so congratulatory on the successes of SP-Tech |
tips 1APp826DqjJBdsAeqpEstx6Q8hD4urac8a
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 01:21:18 PM |
|
one single voluntary RMA in thousands of orders and SP-Tech competitors seem to be having a party about it. it's good that this community are so congratulatory on the successes of SP-Tech We had other RMAs of course, this is the first instance of such sort in the SP20. Guy |
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 01:21:58 PM |
|
[imghttps://i.imgur.com/3NeiVUI.jpg[/img]
modules and controller is fine, will it still cover in warranty if I replace the sockets my self?
How did that happen? everything is just fine for a week, but this morning smells like shit! I know that smell PSUs ok? What cable gauge? What PSU model? Cables came with the PSU? PSU is ok, because both PSU and cables is not mine so im not sure the cable gauge but im sure they is not came with PSU PSU:Super Flower Leadex Platinum 1200W Our connectors are subtitle for up to 24A each and were tested in such condition at ambient of 40C. Issue might be caused due to: 1. loose connectivity between the wire and the pin. 2. dis-connectivity of some of the wires causing over current on the connected wires. 3. over powering the PSU causing heat on wires to melt the connectors - can be for example due to wrong AWG or connectors that are not suitable for high power. 4. home made cables with long wires and unsuitable connector/wires. Can you reply the following: 1. what was the power limit per each of the 4 inputs? (this is defined at the GUI) 2. did you use the ATX original cables? 3. what is the cable AWG? 4. what was the ambient temperature? We'll check the PSU model you were using. Please contact support for RMA, don't attempt to fix yourself. We kindly ask that you'll the PSU and cables for us for further testing. Guy 1.all 288w but only use 230~270w report from ASIC stats 2.no (but cable that of the picture is) 3.I cant tell, maybe 10AWG or 9AWG 4.32C report from another working SP20 i don't wanna go RMA because i think the problem is on my plugs, if you give me a new one that is really not fair to you, i just want to keep this miner cover in warranty after i replaced the socket myself. Indeed, it's most probably a problem with your cables. Use of improper cables voids the warranty of course. However, we want to investigate to be 100% sure. Out of 1,000s of SP20 we sold, this is the first reported instance. I'm offering you free RMA nevertheless, all we want is the PSU and cables. Guy but the PSU is my friend's, could you send it back to me after the testing? Sure. Thanks! information please Contact support@ and Barbara will explain the process. Thanks, Guy |
|
|
|
|
Subw
|
|
December 23, 2014, 01:25:30 PM |
|
SP-Tech competitors seem to be having a party about it. competition is always good for us consumers. now SP20 competes against S4 & S5 and considering bitmain can cut S5's price in half what is SP going to offer us ? |
|
|
|
|
Guy Corem (OP)
Donator
Legendary
Offline
Activity: 1414
Merit: 1051
Spondoolies, Beam & DAGlabs
|
|
December 23, 2014, 01:26:34 PM |
|
SP-Tech competitors seem to be having a party about it. competition is always good for us consumers. now SP20 competes against S4 & S5 and considering bitmain can cut S5's price in half what is SP going to offer us ? |
|
|
|
|
Bicknellski
|
|
December 23, 2014, 01:26:48 PM |
|
SP-Tech competitors seem to be having a party about it. competition is always good for us consumers. now SP20 competes against S4 & S5 and considering bitmain can cut S5's price in half what is SP going to offer us ? How many would you buy to get half price Subw? 100? 200? Is shipping free? |
|
|
|
|
raskul
|
|
December 23, 2014, 01:27:25 PM |
|
SP-Tech competitors seem to be having a party about it. competition is always good for us consumers. now SP20 competes against S4 & S5 and considering bitmain can cut S5's price in half what is SP going to offer us ? How many would you buy to get half price Subw? 100? 200? on your marks... get set... |
tips 1APp826DqjJBdsAeqpEstx6Q8hD4urac8a
|
|
|
RoadStress
Legendary
Offline
Activity: 1904
Merit: 1007
|
|
December 23, 2014, 01:31:54 PM |
|
SP-Tech competitors seem to be having a party about it. competition is always good for us consumers. now SP20 competes against S4 & S5 and considering bitmain can cut S5's price in half what is SP going to offer us ? How many would you buy to get half price Subw? 100? 200? Is shipping free? Join my new GB: https://bitcointalk.org/index.php?topic=903286.0$1,000 for 2xSP20! |
|
|
|
|
Subw
|
|
December 23, 2014, 01:32:05 PM |
|
SP-Tech competitors seem to be having a party about it. competition is always good for us consumers. now SP20 competes against S4 & S5 and considering bitmain can cut S5's price in half what is SP going to offer us ? yeah funny. look at S3 price: 199 USD and S5 does not have second fan and expensive dc/dc circuits |
|
|
|
|
|
