ivanpop
Newbie
 Offline
Activity: 62
Merit: 0
|
 |
August 25, 2016, 12:51:08 PM |
|
They're not wrong. I mine and my PC is completely responsive, like it's not even mining. I can even play CS:GO while mining and I get decent FPS.
|
|
|
|
|
|
|
|
|
|
Bitcoin addresses contain a checksum, so it is very unlikely that mistyping an address will cause you to lose money.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
vapourminer
Legendary
Offline
Activity: 4326
Merit: 3519
what is this "brake pedal" you speak of?
|
|
August 25, 2016, 12:53:39 PM
Last edit: August 25, 2016, 01:50:30 PM by vapourminer |
|
They're not wrong. I mine and my PC is completely responsive, like it's not even mining. I can even play CS:GO while mining and I get decent FPS.
same here. simpler games as in 2-3 year old AAA titles, movies, youtube etc all play well with stock settings. just the system and gpu fans may ramp up a bit. r9 390. EDIT: eth only |
|
|
|
|
|
Tasty Potato
|
|
August 25, 2016, 01:20:03 PM |
|
They're not wrong. I mine and my PC is completely responsive, like it's not even mining. I can even play CS:GO while mining and I get decent FPS.
I checked them with my PC, no help. |
|
|
|
|
|
pwpwpw
|
|
August 25, 2016, 01:38:56 PM |
|
My PC stutters while mining thats why I use -ethi 4 or even -ethi 1, lower hashrate but everything works fine. I doubt you can play games while mining at full speed, normally gpu usage is 99%+, with ethi 1 its 95%, that remaining 5% won't be enough for games. I'm using dcri 80 so maybe with dcri 20, you could play some games.
|
|
|
|
|
xeridea
|
|
August 25, 2016, 02:27:18 PM |
|
Guys, how to decrease GPU load or some other setting in order to use PC for other stuff (surfing, movies, etc)?  I am using this code atm - ethdcrminer64.exe -epool coinotron.com:3344 -ewal X -esm 2 -epsw X -etha 0 -ethi 20 -estale 0 -allpools 1My GPU load is 99-100%, MCU load - 90-93% Is there a way to do it on the fly? Or do I have to ctrl+C the claymore miner all the time I want to run a change in command line code? P.S. I am running gtx 970 in P0 mode at ~3900MHz memory clock with ~19MH/s Default ethi is 8, lower is less load, you have it higher.... You can't change ethi or li on the fly (you can change dcri on the fly though...), but you could make 2 bat files... I mine on 470s, I can run them full out dual mining, and not even notice while working, watching movies etc. When had a 970 as display card though, it would lag the desktop while mining, not sure why the amd cards I have used don't lag. I can even (accidentally) mine on my cheap dual core APU without lag. If you have an APU, or Intel CPU with graphics, plug into that.... |
Profitability over time charts for many GPUs - http://xeridea.us/chartsBTC: bc1qr2xwjwfmjn43zhrlp6pn7vwdjrjnv5z0anhjhn LTC: LXDm6sR4dkyqtEWfUbPumMnVEiUFQvxSbZ Eth: 0x44cCe2cf90C8FEE4C9e4338Ae7049913D4F6fC24 |
|
|
|
Alubert
|
|
August 25, 2016, 03:59:15 PM |
|
Guys, how to decrease GPU load or some other setting in order to use PC for other stuff (surfing, movies, etc)? I am using this code atm - ethdcrminer64.exe -epool coinotron.com:3344 -ewal X -esm 2 -epsw X -etha 0 -ethi 20 -estale 0 -allpools 1My GPU load is 99-100%, MCU load - 90-93% Is there a way to do it on the fly? Or do I have to ctrl+C the claymore miner all the time I want to run a change in command line code? P.S. I am running gtx 970 in P0 mode at ~3900MHz memory clock with ~19MH/s Default ethi is 8, lower is less load, you have it higher.... You can't change ethi or li on the fly (you can change dcri on the fly though...), but you could make 2 bat files... I mine on 470s, I can run them full out dual mining, and not even notice while working, watching movies etc. When had a 970 as display card though, it would lag the desktop while mining, not sure why the amd cards I have used don't lag. I can even (accidentally) mine on my cheap dual core APU without lag. If you have an APU, or Intel CPU with graphics, plug into that.... I use the old 7970 to mine Ethereum with the Claymore miners. It has quite big lag when it is used as the main display. I do not know why. |
|
|
|
|
|
PovertyByte
|
|
August 25, 2016, 04:33:21 PM
Last edit: August 25, 2016, 05:58:50 PM by PovertyByte |
|
I can't get DCR to mine. Based on what I do in the config, dpools, and start files I either get "DCR: Authorization failed" on startup with all my shares rejected or I just hash at 0 for DCR
Try this: Claymore command for merged ETC + DCR: ethdcrminer64.exe -epool etc-eu.suprnova.cc:3333 -ewal suprnova.1 -epsw x -esm 3 -dpool dcr.suprnova.cc:2252 -dwal suprnova.1 -dpsw x -allpools 1 Will make you mine ETC at first and DCR as second coin, both on suprnova, make sure you have an account and worker set up. ( https://dcr.suprnova.cc) So I run this as my batch file with with exactly that as listed on the dcr.suprnova.cc page. Do I edit my wallet address over the "1" in the "-dwal suprnove.1"? Also it would seem that eth mining worked with my current ethermine.org in the batch file. I just want to make sure that it isn;t a necessity to run both of those on the suprnova pools. Do I just use suprnova.1 in the batch file and the decred wallet in the config? Far as suprnova I made a worker but I do not know what to do with that. edit: I think I get it. supernova.1 is supposed to be my pool username.workername. Figured it out while trying to get LBRY mining working. I read that there is improper fan and power controls for nvidia dual mining right now so I will get back to this later. |
|
|
|
|
bensam1231
Legendary
Offline
Activity: 1750
Merit: 1024
|
|
August 25, 2016, 04:46:33 PM |
|
it allows the dev fee to be mined at some predefined pools
As opposed to what? Disabling dev fee? |
I buy private Nvidia miners. Send information and/or inquiries to my PM box.
|
|
|
|
alevlaslo
|
|
August 25, 2016, 05:06:28 PM |
|
Coinotron pool has auto switch between ETH and ETC to more profit
|
Sale the first NFT of the first foto
|
|
|
|
Tasty Potato
|
|
August 25, 2016, 07:10:40 PM |
|
My PC stutters while mining thats why I use -ethi 4 or even -ethi 1, lower hashrate but everything works fine. I doubt you can play games while mining at full speed, normally gpu usage is 99%+, with ethi 1 its 95%, that remaining 5% won't be enough for games. I'm using dcri 80 so maybe with dcri 20, you could play some games.
yes, thank you for your time and possible solutions in my issue, i got them nailed. Gaming is out of the question or else I need to drop hashrate even further. |
|
|
|
|
|
Tasty Potato
|
|
August 25, 2016, 07:46:02 PM |
|
Guys, how to decrease GPU load or some other setting in order to use PC for other stuff (surfing, movies, etc)? I am using this code atm - ethdcrminer64.exe -epool coinotron.com:3344 -ewal X -esm 2 -epsw X -etha 0 -ethi 20 -estale 0 -allpools 1My GPU load is 99-100%, MCU load - 90-93% Is there a way to do it on the fly? Or do I have to ctrl+C the claymore miner all the time I want to run a change in command line code? P.S. I am running gtx 970 in P0 mode at ~3900MHz memory clock with ~19MH/s Default ethi is 8, lower is less load, you have it higher.... You can't change ethi or li on the fly (you can change dcri on the fly though...), but you could make 2 bat files... I mine on 470s, I can run them full out dual mining, and not even notice while working, watching movies etc. When had a 970 as display card though, it would lag the desktop while mining, not sure why the amd cards I have used don't lag. I can even (accidentally) mine on my cheap dual core APU without lag. If you have an APU, or Intel CPU with graphics, plug into that.... Thank you for your time and advice, I found solution with the help of the dev by using -li. That did a nice, fine and silky job ;] |
|
|
|
|
clipto
Member
Offline
Activity: 311
Merit: 10
|
|
August 25, 2016, 08:13:33 PM |
|
Been playing with some of the more advanced features of the miner.
Temp control, voltage control, etc.
One of my 4 cards gives me this error, how to fix this?
Failed to set new Power Control treshold for GPU #0
del *_log.txt
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xxxxxxxxxxx/MiningrigAMD -epsw x -dpool sia.suprnova.cc:7777 -dwal xxxx.gpu -dpsw x -dcoin sia -allpools 1 -powlim -18 -cvddc 1030 -tt -100 -ttdcr 80
Card #0 = a AMD 280x by the way.
Running at Crimson 16.3.2 driver by the way.
|
|
|
|
|
|
Tasty Potato
|
|
August 25, 2016, 08:23:58 PM |
|
Guys, how to decrease GPU load or some other setting in order to use PC for other stuff (surfing, movies, etc)? I am using this code atm - ethdcrminer64.exe -epool coinotron.com:3344 -ewal X -esm 2 -epsw X -etha 0 -ethi 20 -estale 0 -allpools 1My GPU load is 99-100%, MCU load - 90-93% Is there a way to do it on the fly? Or do I have to ctrl+C the claymore miner all the time I want to run a change in command line code? P.S. I am running gtx 970 in P0 mode at ~3900MHz memory clock with ~19MH/s try -li 10 or more That's what did the trick, thank you, I got the same advice from the dev. |
|
|
|
|
goofy73
Member
Offline
Activity: 65
Merit: 10
|
|
August 25, 2016, 09:24:11 PM |
|
Claymore, could you do some ethman modification: let ethman show "off" instead gpu temperature of those cards, wich was switched off by max temp reached or another reason
|
|
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
|
August 25, 2016, 09:30:22 PM |
|
Claymore, could you do some ethman modification: let ethman show "off" instead gpu temperature of those cards, wich was switched off by max temp reached or another reason
Ok, will be added in next update. |
|
|
|
mr.pacy.mf
Jr. Member
Offline
Activity: 408
Merit: 3
|
|
August 25, 2016, 09:43:54 PM |
|
to high power consumation on sia+eth 1215w vs 990w 4x390x eth + sia vs eth solo 1055/1500 -100mv
|
They say I act like I don't give a fuck...I tell them I'm not acting...It's just who I am...
|
|
|
|
nhando
|
|
August 26, 2016, 12:11:01 AM |
|
What are you guys getting hash rate wise for NVIDIA 1070 dual mining with SIA using Claymore?
|
Just "Mining" my own business.
|
|
|
SwedishBTC
Newbie
Offline
Activity: 34
Merit: 0
|
|
August 26, 2016, 01:11:38 AM |
|
I am having a problem with one of my rigs it is crashing all the time (sometimes I have to disconnect the power to all GPUs, uninstall the onboard graphics, and then connect the power to all cards again before rebooting the PC to get the PC to boot, and sometimes I even get THREAD_STUCK_IN_DEVICE_DRIVER error message when trying to boot the PC), and I did find out that if I turn off GPU 5 it seems to work better and not crashing.
I am running in Windows 10 x64 with Sappire Radeon RX 480, and I did try different drivers without any luck. And I got the same clock settings on all cards (I am running 4 more RX480 on another machine and that one did not crash one single time in over 3 weeks) This is how the logfile looks right before the crash if I run with GPU 5 on...
02:27:22:161 11f0 ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166 11f0 DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171 11f0 DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s
02:27:22:446 ca0 DCR: weak share, skip
02:27:23:291 6ac DCR: weak share, skip
02:27:23:761 408 GPU0 t=59C fan=44%, GPU1 t=84C fan=61%, GPU2 t=79C fan=53%, GPU3 t=79C fan=58%, GPU4 t=85C fan=61%, GPU5 t=85C fan=60%
02:27:23:766 408 em hbt: 0, dm hbt: 0, fm hbt: 0,
02:27:23:766 408 watchdog - thread 0, hb time 203
02:27:23:771 408 watchdog - thread 1, hb time 94
02:27:23:771 408 watchdog - thread 2, hb time 0
02:27:23:771 408 watchdog - thread 3, hb time 125
02:27:23:776 408 watchdog - thread 4, hb time 31
02:27:23:776 408 watchdog - thread 5, hb time 141
02:27:23:781 408 watchdog - thread 6, hb time 219
02:27:23:781 408 watchdog - thread 7, hb time 110
02:27:23:786 408 watchdog - thread 8, hb time 94
02:27:23:786 408 watchdog - thread 9, hb time 203
02:27:23:791 408 watchdog - thread 10, hb time 77656
02:27:23:791 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:23:796 408 watchdog - thread 11, hb time 77547
02:27:23:801 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:24:806 408 Restarting OK, exit...
This is how my *.bat file looks
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xMyEtherWalletAddress -epsw x -eworker miner2 -dpool stratum+tcp://dcr.coinmine.pl:2222 -dwal MyUsername.miner2 -dpsw MyPassword -dcri 40
What can be wrong, any advice?
|
|
|
|
|
Vetal_inside
Member
Offline
Activity: 78
Merit: 10
|
|
August 26, 2016, 01:22:31 AM |
|
Hi Claymore! At first - seems that it some built-in temp hysteresis parameter, what was set to 4 degr. At example on my rig, when tt limit set to 65 degr., and temp reach this value, fan begin work on 100%. And it continue working on 100%, till temp downs to 61 degr. It would be fine, if there were active option for temp hysteresis, which user can set manually for better configuration rigs. And second: are you planning to add static interface, like cgminer or sgminer? When I looking on moving, from down to top, lines with different colours, I worry that I will get epileptic fit  . But seriously, moving lines is anachronism from standart ethminer. It's time to make normal static interface. |
|
|
|
|
|
joaocha
|
|
August 26, 2016, 01:30:33 AM |
|
Hi Claymore! At first - seems that it some built-in temp hysteresis parameter, what was set to 4 degr. At example on my rig, when tt limit set to 65 degr., and temp reach this value, fan begin work on 100%. And it continue working on 100%, till temp downs to 61 degr. It would be fine, if there were active option for temp hysteresis, which user can set manually for better configuration rigs. And second: are you planning to add static interface, like cgminer or sgminer? When I looking on moving, from down to top, lines with different colours, I worry that I will get epileptic fit . But seriously, moving lines is anachronism from standart ethminer. It's time to make normal static interface. Static interface would be nice!!! |
|
|
|
|
|
