|
Bananana
|
 |
March 03, 2017, 01:59:28 PM |
|
I notice some gtx 1080 required 2-8 pin power connector but they have the same TPD (180w) as those that only have 1-8 pin connector. Can I just plug in 1-8 pin power connector and leave the other one of it empty?
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
bughatti
|
|
March 03, 2017, 04:35:55 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
|
|
|
|
|
|
xeridea
|
|
March 03, 2017, 05:18:05 PM |
|
I notice some gtx 1080 required 2-8 pin power connector but they have the same TPD (180w) as those that only have 1-8 pin connector. Can I just plug in 1-8 pin power connector and leave the other one of it empty?
some cards have more power connectors for increased overclocking headroom. If it has extra connectors you must plug them all in because the card is wired to use all of them. The 1080 doesn't really need more than one a pen but some cards have them anyway. |
Profitability over time charts for many GPUs - http://xeridea.us/chartsBTC: bc1qr2xwjwfmjn43zhrlp6pn7vwdjrjnv5z0anhjhn LTC: LXDm6sR4dkyqtEWfUbPumMnVEiUFQvxSbZ Eth: 0x44cCe2cf90C8FEE4C9e4338Ae7049913D4F6fC24 |
|
|
|
EWBF_ (OP)
|
|
March 03, 2017, 05:28:27 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Hi, can you send me the log file? Use option --log. |
|
|
|
|
m1n1ngP4d4w4n
Full Member
 Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
March 03, 2017, 05:32:06 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
The newest EWBF is a bit more effective, so it push your gpu's a bit more (1-2%) hence why if you had borderline OC's you may have to reduce it a bit (a few %) for your rig to become stable. |
|
|
|
|
|
bughatti
|
|
March 03, 2017, 05:37:31 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Hi, can you send me the log file? Use option --log. Hey EWBF, thanks for the response. I am back at work and cannot send them, it will not be until tonight, about 6 or so hours. I will say I dont have mine pushed very hard. I am using 6 x asus gtx 1060 3gb and using MSI I have power limit at 89 and max temp I think at 75-78. I will play around with the settings again when I get home. I first saw the issue when I went from flypool to nanopool. I would start dropping from just this multi rig ( I have another single 1060 card rig that is stable and fine) about every 6 hours. I went back to flypool since it ran on flypool for a week no issues. Now I started to see it happening there but it would drop after about an hour. |
|
|
|
|
|
EWBF_ (OP)
|
|
March 03, 2017, 05:59:25 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Hi, can you send me the log file? Use option --log. Hey EWBF, thanks for the response. I am back at work and cannot send them, it will not be until tonight, about 6 or so hours. I will say I dont have mine pushed very hard. I am using 6 x asus gtx 1060 3gb and using MSI I have power limit at 89 and max temp I think at 75-78. I will play around with the settings again when I get home. I first saw the issue when I went from flypool to nanopool. I would start dropping from just this multi rig ( I have another single 1060 card rig that is stable and fine) about every 6 hours. I went back to flypool since it ran on flypool for a week no issues. Now I started to see it happening there but it would drop after about an hour. Here most important is a first error code and gpu number, you can simply exclude this gpu, or set him to default settings and look what happens. Anyway would be great if you show me the log. |
|
|
|
|
kapsel
Member
Offline
Activity: 60
Merit: 10
|
|
March 03, 2017, 06:03:36 PM |
|
0.3.1b GTX 1080 FE
570 sol/s with max oc, 120% power limit, +200 core, +1000 mem,
490 sol/s with 65% power limit, +200 core, +0 mem
460 sol/s with 60% power limit, +200 core, +0 mem
450 sol/s with 60% power limit, +200 core, +500 mem
350 sol/s with 50% power, +200 core, +0 mem
330 sol/s with 50% power, +200 core, +500 mem
It seems that overclocking memory past 0 tends to give next to no performance increase, and overclocking it too much with low power causes core clock to be lower and actually slowing down speed. Sweet spot for me seems to be around 60% power limit, dropping below 60% causes very large drop in speed.
|
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
March 03, 2017, 07:21:53 PM |
|
sweet core OC !, indeed for zcash memory OC bring barely anything, good numbers there  |
|
|
|
|
minerx117
Sr. Member
Offline
Activity: 728
Merit: 256
NemosMiner-v3.8.1.3
|
|
March 03, 2017, 08:06:18 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
im getting exactly the same problems only happened after i upgraded from 0.3.0b to 0.3.1b havn't changed anything else 0.3.0b works fine so i am rolling back to 0.3.0b until this has been resolved (single 1050ti runs fine with 0.3.1b but the 1070x 5 rig doesnt like it at all .... |
NemosMiner-v3.8.1.3
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
March 03, 2017, 08:33:28 PM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
im getting exactly the same problems only happened after i upgraded from 0.3.0b to 0.3.1b havn't changed anything else 0.3.0b works fine so i am rolling back to 0.3.0b until this has been resolved (single 1050ti runs fine with 0.3.1b but the 1070x 5 rig doesnt like it at all .... Really weird, i have 60x 1070 running this version without a problem non stop since it has been released. what OC / tdp / nvidia smi reading, are you using ? |
|
|
|
|
minerx117
Sr. Member
Offline
Activity: 728
Merit: 256
NemosMiner-v3.8.1.3
|
|
March 03, 2017, 09:05:22 PM |
|
Really weird, i have 60x 1070 running this version without a problem non stop since it has been released. what OC / tdp / nvidia smi reading, are you using ? g1 gaming -30% power / +199mhz core / -1210mhz memory / temp 90 = 0.3.0b = 407sols for 99watt g1 gaming -30% power / +199mhz core / -1210mhz memory / temp 90 = 0.3.1b = 0sols could be my memory underclock yeh  works fine with all the ccminers and 0.3.0b tho .... Regards #Nemo |
NemosMiner-v3.8.1.3
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
March 03, 2017, 09:28:28 PM |
|
Yeah could be, also the core OC may be a little too aggressive, this new ewbf version really max out the gpu's more than before. try lowering it a bit to see how it goes.
|
|
|
|
|
minerx117
Sr. Member
Offline
Activity: 728
Merit: 256
NemosMiner-v3.8.1.3
|
|
March 03, 2017, 09:30:33 PM |
|
Yeah could be, also the core OC may be a little too aggressive, this new ewbf version really max out the gpu's more than before. try lowering it a bit to see how it goes.
what tdp and clocks are you using for your 1070 's |
NemosMiner-v3.8.1.3
|
|
|
|
EWBF_ (OP)
|
|
March 03, 2017, 09:36:39 PM |
|
Really weird, i have 60x 1070 running this version without a problem non stop since it has been released. what OC / tdp / nvidia smi reading, are you using ? g1 gaming -30% power / +199mhz core / -1210mhz memory / temp 90 = 0.3.0b = 407sols for 99watt g1 gaming -30% power / +199mhz core / -1210mhz memory / temp 90 = 0.3.1b = 0sols could be my memory underclock yeh works fine with all the ccminers and 0.3.0b tho .... Regards #Nemo Did you try solver 2? |
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
March 03, 2017, 09:42:45 PM |
|
Yeah could be, also the core OC may be a little too aggressive, this new ewbf version really max out the gpu's more than before. try lowering it a bit to see how it goes.
what tdp and clocks are you using for your 1070 's 150/595 @112w (60% tdp for me) 440sols/s per card |
|
|
|
|
minerx117
Sr. Member
Offline
Activity: 728
Merit: 256
NemosMiner-v3.8.1.3
|
|
March 03, 2017, 10:43:23 PM |
|
Yeah could be, also the core OC may be a little too aggressive, this new ewbf version really max out the gpu's more than before. try lowering it a bit to see how it goes.
what tdp and clocks are you using for your 1070 's 150/595 @112w (60% tdp for me) 440sols/s per card thanks ive sorted it ill update my miner to 1.6.1 again thankx for the help |
NemosMiner-v3.8.1.3
|
|
|
PressEnterNoaw
Newbie
Offline
Activity: 16
Merit: 0
|
|
March 03, 2017, 11:29:20 PM |
|
Yeah could be, also the core OC may be a little too aggressive, this new ewbf version really max out the gpu's more than before. try lowering it a bit to see how it goes.
I concur, 1070 core should be at ~2050Mhz~ for max stability/performance, and I keep my mem at +400-500mhz (afterburner settings, without tdp limit) |
|
|
|
|
kell234
Newbie
Offline
Activity: 17
Merit: 0
|
|
March 04, 2017, 01:44:17 AM |
|
Error 46 was only with last nvidai drivers
With 378 all ok
|
|
|
|
|
|
bughatti
|
|
March 04, 2017, 01:44:59 AM |
|
I have noticed over the last few days I keep getting this. I saw it with the newer version and then went back to 3b. The only other difference is I went from suprnova to flypool. I will put it back on suprnova to see if it resolves but wandered if you know why this is happening
INFO: GPU1 are restarted.
CUDA: Device: 0 User selected solver: 0
CUDA: Device: 1 User selected solver: 0
ERROR: Looks like GPU2 are stopped. Restart attempt.
INFO: GPU2 are restarted.
ERROR: Looks like GPU3 are stopped. Restart attempt.
INFO: GPU3 are restarted.
ERROR: Looks like GPU4 are stopped. Restart attempt.
INFO: GPU4 are restarted.
ERROR: Looks like GPU5 are stopped. Restart attempt.
INFO: GPU5 are restarted.
CUDA: Device: 1 Thread exited with code: 46
CUDA: Device: 0 Thread exited with code: 46
CUDA: Device: 2 User selected solver: 0
CUDA: Device: 5 User selected solver: 0
CUDA: Device: 4 User selected solver: 0
CUDA: Device: 3 User selected solver: 0
CUDA: Device: 2 Thread exited with code: 46
CUDA: Device: 3 Thread exited with code: 46
CUDA: Device: 4 Thread exited with code: 46
CUDA: Device: 5 Thread exited with code: 46
Temp: GPU0: 28C GPU1: 29C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Temp: GPU0: 28C GPU1: 28C GPU2: 30C GPU3: 28C GPU4: 24C GPU5: 30C
GPU0: 0 Sol/s GPU1: 0 Sol/s GPU2: 0 Sol/s GPU3: 0 Sol/s GPU4: 0 Sol/s GPU5: 0 Sol/s
Total speed: 0 Sol/s
Hi, can you send me the log file? Use option --log. Hey EWBF, I will hold off for a bit on sending log. My miner seems to be acting much more stable on suprnova. I will watch it for a few days to see if it errors. |
|
|
|
|
|
