[ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs

[Zelek Uther]

Guy, I would be interested in your thoughts on this:
http://www.coindesk.com/kncminer-plans-16nm-bitcoin-mining-asic-launch-2015/

Does ST have plans for a competing product launch at about the same timeframe?

[1714904654]

1714904654

[1714904654]

1714904654

[philipma1957]

Guy, I would be interested in your thoughts on this:
http://www.coindesk.com/kncminer-plans-16nm-bitcoin-mining-asic-launch-2015/

Does ST have plans for a competing product launch at about the same timeframe?

I can bet you it won't be a 16nm.  the article has  typo some times  it reads 16nm other times it reads 14nm they have been bragging about the new chip since sept. 2014.

I also think based on everything I have seen  the 14/16nm chip  will not go from .7w to .07w .

I think they are bs ing a whole lot saying they can do a 10x improvement .   they will be lucky to get to .5w or .4w .   but what do I know.

Now if they build a solid .4 watt miner and no one else has one doing better then .6w they will have a decent edge over everyone until others make good a good .4w miner.

[Marvell1]

So you are saying four connectors pulling 300watts per for the sp20 is the the issue ?  

I don't see how that could be the issue I think its either an issue with the firmware or the Asics themselves.

If a sp31 does 4.8 - 5 TH using the same chips at 2800 watts.  

A sp20 should be able to do at least 1.8 TH using 1200 watts of power unless something is seriously goofed, since it is the same silicon basically.



If you are right and it is an issue of Maybe it is an issue of the SP20 needing to be able to pull a bit more juice  say 330watts vs 300 thats a different issue I guess.

Either way 1650 TH is not good for 1200 Watts and that is what the majority of folks are seeing.  I'm leaning to maybe canceling my order if this is something set in stone.

Yes I think they did a design flaw since most current/watts  sent on 4 connectors = 4 x 288 or 1152 watts.  that is the max rating.  so when you try to send 1200 watts over a 1152 rated connection you waste power.  I

 In my case I do not care about this issue since I plan to use 250 setting not the 288 setting.  but any one wanting to send 288 or more is just wasting money.
I would love to see clear testing from some one that used an evga 1300 or an evga 1600 set at watts of 225 to 250.
I am pretty sure those will be the best watt to gh settings.

I am going to have a lot of fun with this gear in the underclock undervolt world should be fun for me.   but if you are an oc dude/dudette this may be bad gear.

I will be posting that info shortly, including evga 1200, 1600 as well as a few others....

 I will also post my evga g2 1300 and my evga p2 1600 when I get the sp20

My opinion is this 250 watts should be your max setting  and underclocking should be what you want to do.

Basically  due to the 4 jack setup since the jacks rate at 288/300 watts and you want a margin of safety so 250 should be ideal.  maybe 225 or 240 but I do not know if 225 or 240 can be set.

This is strictly based on the rating for those jacks and for evga 1300/1600 wires .   I will be happy with 1000 watts and 1400 hash

you have to be kidding me 1.4 TH at 1000 watts is a joke. you get better performance out of an sp10.  Why even buy the unit if that is your target.

[ManeBjorn]

The thing that bothers me with any KnC claims is the fact they said they are not going to sell miners anymore so they can claim any numbers they want and reviewers like Me and Dogie will not get our hands on the to fact check.  Any business they sell to will most likely be under an NDA so it will be hard to verify for sure.

I have an interview with Guy from Spondoolies going live tomorrow.  No matter what the others do SP-Tech is not stopping.  Pretty cool actually to see so many companies doing well and working hard for improvements.

Guy impressed me a lot when I met him in person.  

Guy, I would be interested in your thoughts on this:
http://www.coindesk.com/kncminer-plans-16nm-bitcoin-mining-asic-launch-2015/

Does ST have plans for a competing product launch at about the same timeframe?

I can bet you it won't be a 16nm.  the article has  typo some times  it reads 16nm other times it reads 14nm they have been bragging about the new chip since sept. 2014.

I also think based on everything I have seen  the 14/16nm chip  will not go from .7w to .07w .

I think they are bs ing a whole lot saying they can do a 10x improvement .   they will be lucky to get to .5w or .4w .   but what do I know.

Now if they build a solid .4 watt miner and no one else has one doing better then .6w they will have a decent edge over everyone until others make good a good .4w miner.

[Guy Corem]

Guy, I would be interested in your thoughts on this:
http://www.coindesk.com/kncminer-plans-16nm-bitcoin-mining-asic-launch-2015/

Does ST have plans for a competing product launch at about the same timeframe?

Some comments on https://www.kncminer.com/news/news-118:

- When you don't intend to ship anything, you can come out with whatever FUD numbers you want
- 16ff+ will be ready for mass production in Q3
- 0.07 J/GH is nothing special on 16ff+. It's achievable even on 28, if you employ extreme non standard design techniques (which I won't get into) and under-volt the ASIC considerably. The real questions are what will be the GHs/mm^2 (hashing silicon density) and $/GHs (total system cost) when achieving it.

Guy

[philipma1957]

So you are saying four connectors pulling 300watts per for the sp20 is the the issue ?  

I don't see how that could be the issue I think its either an issue with the firmware or the Asics themselves.

If a sp31 does 4.8 - 5 TH using the same chips at 2800 watts.  

A sp20 should be able to do at least 1.8 TH using 1200 watts of power unless something is seriously goofed, since it is the same silicon basically.



If you are right and it is an issue of Maybe it is an issue of the SP20 needing to be able to pull a bit more juice  say 330watts vs 300 thats a different issue I guess.

Either way 1650 TH is not good for 1200 Watts and that is what the majority of folks are seeing.  I'm leaning to maybe canceling my order if this is something set in stone.

Yes I think they did a design flaw since most current/watts  sent on 4 connectors = 4 x 288 or 1152 watts.  that is the max rating.  so when you try to send 1200 watts over a 1152 rated connection you waste power.  I

 In my case I do not care about this issue since I plan to use 250 setting not the 288 setting.  but any one wanting to send 288 or more is just wasting money.
I would love to see clear testing from some one that used an evga 1300 or an evga 1600 set at watts of 225 to 250.
I am pretty sure those will be the best watt to gh settings.

I am going to have a lot of fun with this gear in the underclock undervolt world should be fun for me.   but if you are an oc dude/dudette this may be bad gear.

I will be posting that info shortly, including evga 1200, 1600 as well as a few others....

 I will also post my evga g2 1300 and my evga p2 1600 when I get the sp20

My opinion is this 250 watts should be your max setting  and underclocking should be what you want to do.

Basically  due to the 4 jack setup since the jacks rate at 288/300 watts and you want a margin of safety so 250 should be ideal.  maybe 225 or 240 but I do not know if 225 or 240 can be set.

This is strictly based on the rating for those jacks and for evga 1300/1600 wires .   I will be happy with 1000 watts and 1400 hash

you have to be kidding me 1.4 TH at 1000 watts is a joke. you get better performance out of an sp10.  Why even buy the unit if that is your target.

1000/1400 = 0.714 watts

  max rating for this unit is 1152/1700 = 0.677 watts

 I am okay with 0.714 vs 0.677 watts .

    frankly I did not expect  them to make spec as almost no one make spec.  but the price drop down to 795 sold me.
As long as they are pretty quick with shipping I am fine.

[Guy Corem]

So are the SP20's shipping today the 18th or the 26th now?

Due to the huge demand, some of the miners will be shipped late.
We'll compensate for the diff from later of the (18th,  day of payment received) until the day of actually shipping.

Guy

[philipma1957]

So are the SP20's shipping today the 18th or the 26th now?

Due to the huge demand, some of the miners will be shipped late.
We'll compensate for the diff from later of the (18th,  day of payment received) until the day of actually shipping.

Guy

thanks

   at  a rate of :

1400gh = 0.01747 a day
1500gh = 0.01872 a day
1600gh = 0.01997 a day
1700gh = 0.02121 a day

I used https://bitcoinwisdom.com/bitcoin/difficulty

I purchased early around the 12th so my clock starts on the 18th  it is now the 19th so 1 day so far.

[Guy Corem]

So are the SP20's shipping today the 18th or the 26th now?

Due to the huge demand, some of the miners will be shipped late.
We'll compensate for the diff from later of the (18th,  day of payment received) until the day of actually shipping.

Guy

thanks

   at  a rate of :

1400gh = 0.01747 a day
1500gh = 0.01872 a day
1600gh = 0.01997 a day
1700gh = 0.02121 a day

I used https://bitcoinwisdom.com/bitcoin/difficulty

I purchased early around the 12th so my clock starts on the 18th  it is now the 19th so 1 day so far.

0.02125 BTC per day

[notlist3d]

So are the SP20's shipping today the 18th or the 26th now?

Due to the huge demand, some of the miners will be shipped late.
We'll compensate for the diff from later of the (18th,  day of payment received) until the day of actually shipping.

Guy

Thank you Guy! Top notch support to do this.

You guys had me wanting to buy a SP gear since the Chicago BTC conference.  Looking forward to getting to us a SP made hardware.

[stan258]

So are the SP20's shipping today the 18th or the 26th now?

Due to the huge demand, some of the miners will be shipped late.
We'll compensate for the diff from later of the (18th,  day of payment received) until the day of actually shipping.

Guy

Thank you Guy! Top notch support to do this.

You guys had me wanting to buy a SP gear since the Chicago BTC conference.  Looking forward to getting to us a SP made hardware.

Spondoolies-Tech did ok with compensation last batch. I'm not worried. 

[zvisha]

Hi Guys,
We have a heap of SP30 miners, all working pretty great thanks.
Tonight one miner shows an error on the ASIC page
disabled (Asic all engines fail BIST)
I have restarted miner gate, this doesn't make any difference
I have disabled and enabled in the Settings > ASICS Control Panel, this also makes no difference
I have rebooted the miner at the mains, this again makes no difference.
Yesterday I upgraded all miners to version 2.5.12. 
The settings on this miner are as follows
Fan Speed 80
Start Volts Top 0.64
Start Volts Bottom 0.64
Max Volts 0.79
Max PSU Top 1360
Max PSU Bottom 1360
Temp Front / Back T,B 16c / 52,53c
Socket Voltage 222/221 volt
Any assistance would be gratefully received.  Thanks Guys

What is the effect on the hash rate of the unit, and what ASIC (number) is that?

[ilikemining]

please help, i'm very new to mining and not very computer literate. i have sp10 dawson. i have windows. I DOWNLOADED bfgminer and dhcp online. When i plug in miner i go to network, right click, then to properties. I have tried going to "change adapter settings", then right clicking local area connection and clicking on properties. Then highlight internet protocol version 6, click on properties button.  Not really sure what to do from here or if i'm even close. Is dhcp working? or Should the sp10 be showing up in network connections?

[raskul]

please help, i'm very new to mining and not very computer literate. i have sp10 dawson. i have windows. I DOWNLOADED bfgminer and dhcp online. When i plug in miner i go to network, right click, then to properties. I have tried going to "change adapter settings", then right clicking local area connection and clicking on properties. Then highlight internet protocol version 6, click on properties button.  Not really sure what to do from here or if i'm even close. Is dhcp working? or Should the sp10 be showing up in network connections?

www.myminer.io

[zvisha]

Hi All
We have now new support team.
You can see them online as spond.support.1 (Sonya) and spond.support.2 (Michael).
They accept direct Skype calls between 14:00-16:00 and 19:00-21:00 Israel time.

You can also send mail like always, to support@spondoolies-tech.com.

If they can not help, they will redirect you to me.

[philipma1957]

So are the SP20's shipping today the 18th or the 26th now?

Due to the huge demand, some of the miners will be shipped late.
We'll compensate for the diff from later of the (18th,  day of payment received) until the day of actually shipping.

Guy

thanks

   at  a rate of :

1400gh = 0.01747 a day
1500gh = 0.01872 a day
1600gh = 0.01997 a day
1700gh = 0.02121 a day

I used https://bitcoinwisdom.com/bitcoin/difficulty

I purchased early around the 12th so my clock starts on the 18th  it is now the 19th so 1 day so far.

0.02125 BTC per day

 

 that looks better then my numbers thanks.

[ilikemining]

please help, i'm very new to mining and not very computer literate. i have sp10 dawson. i have windows. I DOWNLOADED bfgminer and dhcp online. When i plug in miner i go to network, right click, then to properties. I have tried going to "change adapter settings", then right clicking local area connection and clicking on properties. Then highlight internet protocol version 6, click on properties button.  Not really sure what to do from here or if i'm even close. Is dhcp working? or Should the sp10 be showing up in network connections?

www.myminer.io

I had tried this and i logged in one time. i was able to change the password. Somehow i logged out and i dont know what my username is? I did not see my username anywhere on the page.  I remember the password, but I can not log back in now.

[ilikemining]

is there anyway to find my username? is there anyway to get back to the first login where admin/admin works?

[raskul]

is there anyway to find my username? is there anyway to get back to the first login where admin/admin works?

username is admin

www.myminer.io and click the bit that says 'go to miner'

 

[ilikemining]

lol  thank you so much!