minerstat: mining OS + ASIC monitoring + Windows mining

[ChaosGen]

Still not working for me. DNS flush works but not resolves the issue.

Could you please provide the IP address of the host so I can use it with the help of hosts file?

[1714949184]

1714949184

[1714949184]

1714949184

[1714949184]

1714949184

[coinscrow]

Still not working for me. DNS flush works but not resolves the issue.

Could you please provide the IP address of the host so I can use it with the help of hosts file?

its take time to be good for everyone as i see here.

https://www.uptrends.com/tools/uptime

few country always down, but need time for a full DNS change.

Thats the new DNS Host: 104.28.31.251

[Jamievs]

Mine just went down too. Nothing changed on my end, that is all I can see/say. Which is interestering because mine went down just now while others had this problems hours earlier.

WINDOWS:
On your keyboard, press Win+X to open the WinX Menu.
Right-click Command Prompt and select Run as Administrator.
Run the following command:

Code:

ipconfig /flushdns

OSX:

Code:

sudo dscacheutil -flushcache; sudo killall -HUP mDNSResponder; 

Can I just wait this out or reboot PC's? It is gonna be a b*tch to log into all rigs and have do this manually.

[mrde12]

Mine just went down too. Nothing changed on my end, that is all I can see/say. Which is interestering because mine went down just now while others had this problems hours earlier.

WINDOWS:
On your keyboard, press Win+X to open the WinX Menu.
Right-click Command Prompt and select Run as Administrator.
Run the following command:

Code:

ipconfig /flushdns

OSX:

Code:

sudo dscacheutil -flushcache; sudo killall -HUP mDNSResponder; 

not work for me

[twan69666]

I'm having the same issue as well, but my rig is remote.

I'd rather not try to reset the ip's or dns's remotely in case something goes down. I'm just going to wait it out until I can get back in front of it later today

[coinscrow]

i contacted the support with the old server the new server is working great.

C:/Windows/System32/drivers/etc/
edit hosts file

PUT

Code:

185.58.227.15 minerstat.com

thats fix the problem or the time will fix it later today..  

* you can't edit host file in its folder, copy to desktop edit, after put back.
* IP IS UPDATED

[magnoman]

i contacted the support with the old server the new server is working great.

C:/Windows/System32/drivers/etc/
edit hosts file

PUT

Code:

104.28.31.251 minerstat.com

thats fix the problem or the time will fix it later today..  

At work I can hit the site just fine but at home it still doesn't resolve to an IP.  DNS changes can take a few hours to go through everywhere so just have to be patient.

At least the miners are still mining.  

**Just don't reboot rigs or restart node until you can hit the website from one of your rigs.**. - Or be prepared to edit hosts file.

[coinscrow]

i contacted the support with the old server the new server is working great.

C:/Windows/System32/drivers/etc/
edit hosts file

PUT

Code:

185.58.227.15 minerstat.com

thats fix the problem or the time will fix it later today..  

At work I can hit the site just fine but at home it still doesn't resolve to an IP.  DNS changes can take a few hours to go through everywhere so just have to be patient.

At least the miners are still mining.  

**Just don't reboot rigs or restart node until you can hit the website from one of your rigs.**. - Or be prepared to edit hosts file.

Yes, not effect on mining just stats. When you can reach minerstat.com on your browser the client will work.

[Jamievs]

Just to confirm, I didn't do anything and all my rigs just turned up online again in the dashboard!

[coinscrow]

Just to confirm, I didn't do anything and all my rigs just turned up online again in the dashboard!

Need time to this, but will be good for everyone in a short time.

Also, if everyone notice the ZEN is listed on Bittrex or Coinmarketcap please tell me to i can finish the calculation.

[phila]

Maybe it can be made so it doesn't have to close and open clamore-eth miner every time when pool changes from one ethash coin to another and only open a new miner if the algo is different eg. Ethash coin to Equihash coin.

[magnoman]

Maybe it can be made so it doesn't have to close and open clamore-eth miner every time when pool changes from one ethash coin to another and only open a new miner if the algo is different eg. Ethash coin to Equihash coin.

Claymore would need to rebuild/load the DAG database anyway when switching from one Ethash coin to another Ethash coin.  That is the most time consuming part of the Eth miner startup.  Already Claymore is pretty fast compared to others.  One thing that might work is if the Claymore miner could be paused.  NiceHash does this with their Ethash miner so it doesn't have to rebuild DAG if it goes from Ethash to other coin and back to Ethash.

If you could pause Claymore then you could run two instances pause and switch between them and also start other miner if better profit.  That would probably use a lot of RAM/virtual mem though and require Claymore to make some changes to his miner to support it.  Might overly complicate the way the node runs and monitors.

[Namhsac]

on the graph max showed rigs is 8. Can you change it that i can see all of mine?

[olaf_d]

Just to confirm, I didn't do anything and all my rigs just turned up online again in the dashboard!

Need time to this, but will be good for everyone in a short time.

Also, if everyone notice the ZEN is listed on Bittrex or Coinmarketcap please tell me to i can finish the calculation.

It is on coinmarketcap now, https://coinmarketcap.com/currencies/zencash/

[insaniak]

I am unable to connnect to the website

[coinscrow]

We are under attack. I'm working on to get the site back from the overload..

*UPDATE The DDOS comed from the Czech Republic and North America from the ip's i checked. Just a few boring guys 

I'm trying to get a solution, how to prevent these attacks in the future. All data is safe and all miners is up and running.

[mrde12]

Ddos again? i cant access website

[cryptominer420]

Talk to the guys at cloudflare.com there paid solutions are pretty good.

Also a side note, the miner should connect to a remote SQL database for submitting, getting their data. This server should only allow X number of connections from 1 IP every minute so If I am paying to use 10 rigs I should be able to send 20 requests per minute before the IP being blocked as it takes 1 request to get the launch perimeters to the program and then It should send a packet out every Minute. I also have said 20 to allow some head room for rig tweaking (which should be done before the web configurations are ever set but we have to account for noobs). This would also help to prevent people from running multiple rigs under one Worker name.

[coinscrow]

Talk to the guys at cloudflare.com there paid solutions are pretty good.

Also a side note, the miner should connect to a remote SQL database for submitting, getting their data. This server should only allow X number of connections from 1 IP every minute so If I am paying to use 10 rigs I should be able to send 20 requests per minute before the IP being blocked as it takes 1 request to get the launch perimeters to the program and then It should send a packet out every Minute. I also have said 20 to allow some head room for rig tweaking (which should be done before the web configurations are ever set but we have to account for noobs). This would also help to prevent people from running multiple rigs under one Worker name.

I turned off apache right now.
I'm working an a possible permanent fix.

The website comes back in a few hours..

[magnoman]

Talk to the guys at cloudflare.com there paid solutions are pretty good.

Also a side note, the miner should connect to a remote SQL database for submitting, getting their data. This server should only allow X number of connections from 1 IP every minute so If I am paying to use 10 rigs I should be able to send 20 requests per minute before the IP being blocked as it takes 1 request to get the launch perimeters to the program and then It should send a packet out every Minute. I also have said 20 to allow some head room for rig tweaking (which should be done before the web configurations are ever set but we have to account for noobs). This would also help to prevent people from running multiple rigs under one Worker name.

I turned off apache right now.
I'm working an a possible permanent fix.

The website comes back in a few hours..

No big deal at all coinscrow.  Miners are still mining.

Thanks for keeping us informed.