UniJo
Jr. Member
Offline
Activity: 60
Merit: 2
|
|
February 11, 2021, 07:43:06 AM |
|
Looking for tips on fan control. I am trying to set fan speeds and not sure I can do what I want. I know -tt 60 will set temperature target at 60 deg and -tt -70 will set fan speed to 70%. How do I implement more than one set of target temps? I am trying to set these values and fan speeds - 50deg at 60% - 63deg at 70% - 76deg at 80% I am thinking I need this in my config -tt 50 -tt -60 -tt 63 -tt -70 -tt 76 -tt -80 Is this correct or am I missing something? Thanks in advance for any input This is incorrect. -tt 60 sets the target temp to 60 degrees. So it sets the fan speeds at a variable setpoint to keep the card at 60 degrees. With some cards it needs a fan speed of 40% when other cards are set at 75% fan speed. So you can only set 1 target temp for each card.
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
zharow3
Newbie
Offline
Activity: 1
Merit: 0
|
|
February 11, 2021, 11:20:12 AM |
|
one of the best miners. thanks.
|
|
|
|
JeffJohnsonTheNameYouKnow
Jr. Member
Offline
Activity: 41
Merit: 2
|
|
February 11, 2021, 03:58:31 PM |
|
Please fix so it works for Windows 7 & 8
|
|
|
|
CGS_CC
Newbie
Offline
Activity: 11
Merit: 0
|
|
February 11, 2021, 03:59:17 PM |
|
Looking for tips on fan control. I am trying to set fan speeds and not sure I can do what I want. I know -tt 60 will set temperature target at 60 deg and -tt -70 will set fan speed to 70%. How do I implement more than one set of target temps? I am trying to set these values and fan speeds - 50deg at 60% - 63deg at 70% - 76deg at 80% I am thinking I need this in my config -tt 50 -tt -60 -tt 63 -tt -70 -tt 76 -tt -80 Is this correct or am I missing something? Thanks in advance for any input This is incorrect. -tt 60 sets the target temp to 60 degrees. So it sets the fan speeds at a variable setpoint to keep the card at 60 degrees. With some cards it needs a fan speed of 40% when other cards are set at 75% fan speed. So you can only set 1 target temp for each card. Thanks I will continue to run fan controls in OverdriveNTool then I suppose.
|
|
|
|
mrbugera2
Jr. Member
Offline
Activity: 85
Merit: 2
|
|
February 11, 2021, 04:00:27 PM |
|
Hey guys,
My miner was running fine for 4months, since today im getting this error in phoenix miner
"Allocating buffers failed with: clCreateBuffer (-61)
Also it says "Increase Windows Page file size to at least 29GB to avoid out of memory errors and unexpected crashes"
My windows Page file size is at 40GB but it still just gives me these errors.
Anybody got a solution? Any thoughts are appreciated.
|
|
|
|
batsonxl
Member
Offline
Activity: 1196
Merit: 26
|
|
February 11, 2021, 04:56:01 PM |
|
how many cards? Try give 50-60gb
|
|
|
|
batsonxl
Member
Offline
Activity: 1196
Merit: 26
|
|
February 11, 2021, 04:57:44 PM |
|
only 5.4c is stable for me. 5.5b and 5.5c are not stable they just crash with same bat file i used for 5.4c. only 10w 5.5c uses less than 5.4c, and gift is crash
|
|
|
|
Kiawpqe
Jr. Member
Offline
Activity: 63
Merit: 1
|
|
February 11, 2021, 06:02:51 PM |
|
Can someone spare me to send the sample config for binance pool, here??? Thanks. GPU1: 64C 77% 90W, GPU2: 65C 62% 81W, GPU3: 64C 57% 91W, GPU4: 65C 49% 87W, GPU5: 65C 25% 82W, GPU6: 65C 59% 83W, GPU7: 65C 47% 79W GPU1: cclock 1160 MHz, cvddc 868 mV, mclock 2112 MHz GPU2: cclock 1160 MHz, cvddc 868 mV, mclock 2112 MHz GPU3: cclock 1165 MHz, cvddc 868 mV, mclock 2112 MHz GPU4: cclock 1160 MHz, cvddc 868 mV, mclock 2112 MHz GPU5: cclock 1165 MHz, cvddc 868 mV, mclock 2112 MHz GPU6: cclock 1160 MHz, cvddc 868 mV, mclock 2112 MHz GPU7: cclock 1160 MHz, cvddc 868 mV, mclock 2112 MHz GPUs power: 593.5 W; cost: 2.14 USD/day Eth speed: 213.104 MH/s, shares: 3007/0/24, time: 2:10 GPUs: 1: 30.484 MH/s (385/12) 2: 30.393 MH/s (427) 3: 30.463 MH/s (420/7) 4: 30.517 MH/s (485) 5: 30.413 MH/s (445/2) 6: 30.385 MH/s (425/3) 7: 30.449 MH/s (420) *** 2:10 *** 11/14 11:19 ************************************** Eth: Mining ETH on ethash.poolbinance.com:8888 for 2:10 Eth: Accepted shares 3007 (1 stales), rejected shares 0 (0 stales) Eth: Incorrect shares 24 (0.79%), est. stales percentage 0.02% Eth: Maximum difficulty of found share: 547.6 GH (!) Eth: Average speed (5 min): 213.029 MH/s Eth: Effective speed: 205.05 MH/s; at pool: 205.05 MH/s Eth: GPU6: ETH share found! Eth: Share actual difficulty: 2598 MH Eth: Share accepted in 101 ms Eth: GPU4: ETH share found! Eth: Share actual difficulty: 1630 MH Eth: Share accepted in 275 ms Eth speed: 213.110 MH/s, shares: 3009/0/24, time: 2:10 GPUs: 1: 30.482 MH/s (385/12) 2: 30.394 MH/s (427) 3: 30.465 MH/s (420/7) 4: 30.517 MH/s (486) 5: 30.413 MH/s (445/2) 6: 30.389 MH/s (426/3) 7: 30.450 MH/s (420) Eth: GPU7: ETH share found! Eth: Share actual difficulty: 576 MH Eth: Share accepted in 71 ms Eth: New job #5b69f3d0 from ethash.poolbinance.com:8888; diff: 536MH Eth: New job #96e38a96 from ethash.poolbinance.com:8888; diff: 536MH Eth speed: 213.124 MH/s, shares: 3010/0/24, time: 2:10 GPUs: 1: 30.482 MH/s (385/12) 2: 30.396 MH/s (427) 3: 30.465 MH/s (420/7) 4: 30.518 MH/s (486) 5: 30.411 MH/s (445/2) 6: 30.403 MH/s (426/3) 7: 30.449 MH/s (421) Eth: GPU5: ETH share found! Eth: Share actual difficulty: 19.3 GH (!) Eth: Share accepted in 51 ms Eth: GPU4: ETH share found! Eth: Share actual difficulty: 820 MH Eth: Share accepted in 35 ms Eth: GPU2: ETH share found! Eth: Share actual difficulty: 6497 MH Eth: Share accepted in 289 ms DevFee: Connecting to ethash pool asia1.ethpool.org:3333 (proto: EthProxy) DevFee: Connected to ethash pool asia1.ethpool.org:3333 (172.65.215.159) DevFee: New job #cfbb698f from asia1.ethpool.org:3333; diff: 4000MH Eth: GPU4: ETH share found! Eth: Share actual difficulty: 1425 MH Eth: GPU3: ETH share found! Eth: Share actual difficulty: 2451 MH Eth speed: 213.121 MH/s, shares: 3013/0/24, time: 2:10 GPUs: 1: 30.483 MH/s (385/12) 2: 30.395 MH/s (428) 3: 30.464 MH/s (420/7) 4: 30.517 MH/s (487) 5: 30.412 MH/s (446/2) 6: 30.401 MH/s (426/3) 7: 30.449 MH/s (421) Eth: Share accepted in 217 ms Eth: Share accepted in 152 ms pool.binance.com wow 3000 shareds in 2 hours 3-msi Rx-580 8gb 3-gts xxx Rx-580 8gb 1 powercolor Rx-580 8gb hi, bro -pool ethash.poolbinance.com:3333 or -pool ethash.poolbinance.com:443 -pool ethash.poolbinance.com:25 -pool ethash.poolbinance.com:1800 -wal YourEthWalletAddress.WorkerName -proto 2 tutorial of binance https://www.binance.com/en/support/faq/9bd21a9536d74d1fb65c83f8e60ded93low diff= +shares accepted diff: 536MH shares: 3010 no good
|
|
|
|
Kiawpqe
Jr. Member
Offline
Activity: 63
Merit: 1
|
|
February 11, 2021, 06:08:58 PM |
|
Looking for tips on fan control. I am trying to set fan speeds and not sure I can do what I want. I know -tt 60 will set temperature target at 60 deg and -tt -70 will set fan speed to 70%. How do I implement more than one set of target temps? I am trying to set these values and fan speeds - 50deg at 60% - 63deg at 70% - 76deg at 80% I am thinking I need this in my config -tt 50 -tt -60 -tt 63 -tt -70 -tt 76 -tt -80 Is this correct or am I missing something? Thanks in advance for any input This is incorrect. -tt 60 sets the target temp to 60 degrees. So it sets the fan speeds at a variable setpoint to keep the card at 60 degrees. With some cards it needs a fan speed of 40% when other cards are set at 75% fan speed. So you can only set 1 target temp for each card. hi bro try: Gpu 1,Gpu2,Gpu3 -tt 50,63,76 -tt -60,-70,-80 or try MPT.(MorePowerTool) https://www.igorslab.de/
|
|
|
|
Kiawpqe
Jr. Member
Offline
Activity: 63
Merit: 1
|
|
February 11, 2021, 06:16:41 PM |
|
new rig
*** 5:18 *** 2/11 19:12 ************************************** Eth: Mining ETH on ssl://eu1.ethermine.org:5555 for 5:18 Available GPUs for mining: GPU1: AMD Radeon RX 6800 (pcie 11), OpenCL 2.0, 16 GB VRAM, 30 CUs GPU2: Radeon RX 580 Series (pcie 12), OpenCL 2.0, 8 GB VRAM, 36 CUs GPU3: Radeon RX 580 Series (pcie 13), OpenCL 2.0, 8 GB VRAM, 36 CUs GPU4: Radeon RX 580 Series (pcie 14), OpenCL 2.0, 8 GB VRAM, 36 CUs GPU5: Radeon RX 580 Series (pcie 21), OpenCL 2.0, 8 GB VRAM, 36 CUs GPU6: Radeon RX 580 Series (pcie 22), OpenCL 2.0, 8 GB VRAM, 36 CUs GPU7: Radeon RX 580 Series (pcie 23), OpenCL 2.0, 8 GB VRAM, 36 CUs GPU8: AMD Radeon RX 5700 XT (pcie 26), OpenCL 2.0, 8 GB VRAM, 40 CUs GPU1: 50C 43% 167W, GPU2: 60C 39% 88W, GPU3: 60C 40% 95W, GPU4: 57C 34% 86W, GPU5: 59C 33% 82W, GPU6: 60C 30% 82W, GPU7: 58C 30% 83W, GPU8: 48C 26% 90W GPU1: cclock 1176 MHz, cvddc 793 mV, mclock 2098 MHz, Tj 54C GPU2: cclock 1190 MHz, cvddc 862 mV, mclock 2090 MHz GPU3: cclock 1190 MHz, cvddc 862 mV, mclock 2090 MHz GPU4: cclock 1200 MHz, cvddc 862 mV, mclock 2090 MHz GPU5: cclock 1200 MHz, cvddc 856 mV, mclock 2110 MHz GPU6: cclock 1200 MHz, cvddc 856 mV, mclock 2113 MHz GPU7: cclock 1200 MHz, cvddc 856 mV, mclock 2110 MHz GPU8: cclock 1159 MHz, cvddc 750 mV, mclock 1816 MHz, mvddc 850 mV, Tj 53C, Tmem 80C GPUs power: 773.5 W; cost: 2.51 USD/day Current -gt 15,38,38,41,43,42,42,52 Eth: Accepted shares 1463 (0 stales), rejected shares 0 (0 stales) Eth: Incorrect shares 2 (0.14%), est. stales percentage 0.00% Eth: Maximum difficulty of found share: 4285.7 GH (!) Eth: Average speed (5 min): 305.976 MH/s Eth: Effective speed: 306.64 MH/s; at pool: 306.64 MH/s Eth: Estimated income: 33.82 USD/day
1000usd/month 75usd/month of 775watt net 925usd no bad
|
|
|
|
Kiawpqe
Jr. Member
Offline
Activity: 63
Merit: 1
|
|
February 11, 2021, 06:23:32 PM |
|
# # PhoenixMiner configuration file # # -rxboost 0,81,81,81,81,81,81,25 -gt 15,38,38,41,43,42,42,52 -rmode 1 -tt 50,60,60,60,60,60,60,48 -fanmin 30 -fanmax 100 -eres 100 -proto 3 -cdm 2 -hstats 2 -astats 1 -amd -acm -wdog 1 -gpow 100,100,100,100,100,100,100,100 -minRigSpeed 265 -coin eth -clf 1 -clNew 1 -clKernel 1 -prate 0.135 -gpus 1,2,3,4,5,6,7,8 -cclock 1195,1190,1190,1200,1200,1200,1200,1200 -cvddc 793,853,853,855,850,850,850,750 -mclock 2110,2090,2090,2090,2113,2113,2113,1825 -mvddc 850,860,860,860,853,853,853,850 -pool ssl://eu1.ethermine.org:5555 -pool2 ssl://us1.ethermine.org:5555 #GRAVIEX-WALLET #-wal 0x7**********************************.32******* #BINANCE-WALLET -wal 0x7**********************************.32******* -mt 0,0,0,0,0,0,0,0,1 #-pool eu1.ethermine.org:4444 -pool2 us1.ethermine.org:4444 #-wal YourEthWalletAddress.WorkerName #-proto 3 #-cdm 2
Eth: New job #b575c3a7 from ssl://eu1.ethermine.org:5555; diff: 4000MH GPU1: 50C 43% 167W, GPU2: 60C 39% 88W, GPU3: 60C 40% 95W, GPU4: 57C 34% 86W, GPU5: 59C 33% 83W, GPU6: 60C 30% 82W, GPU7: 58C 30% 83W, GPU8: 47C 28% 90W GPU1: cclock 1176 MHz, cvddc 793 mV, mclock 2098 MHz, Tj 55C GPU2: cclock 1190 MHz, cvddc 862 mV, mclock 2090 MHz GPU3: cclock 1190 MHz, cvddc 862 mV, mclock 2090 MHz GPU4: cclock 1200 MHz, cvddc 862 mV, mclock 2090 MHz GPU5: cclock 1200 MHz, cvddc 856 mV, mclock 2110 MHz GPU6: cclock 1200 MHz, cvddc 856 mV, mclock 2113 MHz GPU7: cclock 1200 MHz, cvddc 856 mV, mclock 2110 MHz GPU8: cclock 1159 MHz, cvddc 750 mV, mclock 1816 MHz, mvddc 850 mV, Tj 53C, Tmem 80C GPUs power: 773.1 W; cost: 2.50 USD/day Eth speed: 305.953 MH/s, shares: 1517/0/2, time: 5:28 GPUs: 1: 59.841 MH/s (312) 2: 32.312 MH/s (160) 3: 32.313 MH/s (152/1) 4: 32.281 MH/s (151) 5: 32.489 MH/s (175/1) 6: 32.489 MH/s (160) 7: 32.488 MH/s (163) 8: 51.741 MH/s (244)
|
|
|
|
skablast
Member
Offline
Activity: 476
Merit: 19
|
|
February 11, 2021, 08:25:34 PM |
|
kiawpqe, I tend not to believe that the power at the wall of that rig is 775w. I know that is what the software is reading, but its around 90 w / card.... Good setup e and results, btw
|
|
|
|
greasepit
Newbie
Offline
Activity: 28
Merit: 1
|
|
February 11, 2021, 09:23:19 PM |
|
After updating RX 580 driver from version Adrenalin 2020 Edition 20.4.2 Recommended (WHQL) to version Adrenalin 2020 Edition 20.11.2 Recommended (WHQL) on my 4 rigs, they are now kind of unstable, crashing so often like 2 days uptime maximum
Using Windows 10 PhoenixMiner 5.5c 6 cards each rig
I'll rollback to the oldest driver and see if they get more stable.
Anyone else having the same issue???
Hi everyone I downgraded the drivers version to 20.4.2 but it kept crashing! But after downgrading PhoenixMiner to 5.4c it has resolved. 5.5c is not stable for my Rx 580. A friend of mine is having the same issue with his single Rx 580.
|
|
|
|
Kiawpqe
Jr. Member
Offline
Activity: 63
Merit: 1
|
|
February 11, 2021, 09:30:56 PM |
|
kiawpqe, I tend not to believe that the power at the wall of that rig is 775w. I know that is what the software is reading, but its around 90 w / card.... Good setup e and results, btw
yes bro is PM reading(no wall) 8xgpu (6-RX580,1-RX5700 xt,1RX6800) 775w in PM is well it,nooo? only RX6800 165/175w 58/60MH/s
|
|
|
|
Kiawpqe
Jr. Member
Offline
Activity: 63
Merit: 1
|
|
February 11, 2021, 09:47:49 PM |
|
After updating RX 580 driver from version Adrenalin 2020 Edition 20.4.2 Recommended (WHQL) to version Adrenalin 2020 Edition 20.11.2 Recommended (WHQL) on my 4 rigs, they are now kind of unstable, crashing so often like 2 days uptime maximum
Using Windows 10 PhoenixMiner 5.5c 6 cards each rig
I'll rollback to the oldest driver and see if they get more stable.
Anyone else having the same issue???
Hi everyone I downgraded the drivers version to 20.4.2 but it kept crashing! But after downgrading PhoenixMiner to 5.4c it has resolved. 5.5c is not stable for my Rx 580. A friend of mine is having the same issue with his single Rx 580. i with Adrenalin 2020 Edition 20.12.1 win10
|
|
|
|
nsummy
|
|
February 12, 2021, 03:42:09 AM |
|
Does anyone have the issue of PhoenixMiner essentially locking up the windows system if one of the cards crashes? On mine, I get the notice "Waiting 15s for the previous instance to close" It is then impossible to manually close it, and it requires a full restart.
|
|
|
|
skablast
Member
Offline
Activity: 476
Merit: 19
|
|
February 12, 2021, 05:08:04 AM |
|
Just be aware of the message just before mine:
The official download of phoenix is the one in the first post of the threads not the one in the post before.
So, DO NOT USE that LINK
|
|
|
|
badgoodtime
Newbie
Offline
Activity: 1
Merit: 0
|
|
February 12, 2021, 05:08:28 AM |
|
Hello guys,
Can I ask here about my problem ?
I`m trying to mining eth with Phoenix Miner but i`m getting an error message
Phoenix Miner 5.5c Windows/msvc - Release build -----------------------------------------------
CUDA version: 11.0, CUDA runtime: 8.0 No OpenCL platforms found Available GPUs for mining: GPU1: GeForce GTX 1650 (pcie 1), CUDA cap. 7.5, 4 GB VRAM, 14 CUs Nvidia driver version: 461.40 Eth: Loading pools from epools.txt Eth: the pool list contains 6 pools (1 from command-line) Eth: primary pool: ssl://asia1.ethermine.org:5555 Starting GPU mining Eth: Connecting to ethash pool ssl://asia1.ethermine.org:5555 (proto: EthProxy) GPU1: 29C 50% 10W GPUs power: 10.3 W Eth: Connected to SSL ethash pool asia1.ethermine.org:5555 (2606:4700:90:0:d80c:ff8b:7d45:b70e) Listening for CDM remote manager at port 3333 in read-only mode Eth: New job #13a2e45f from ssl://asia1.ethermine.org:5555; diff: 4000MH GPU1: Starting up... (0) GPU1: Generating ethash light cache for epoch #392 Eth: New job #d160df6f from ssl://asia1.ethermine.org:5555; diff: 4000MH Light cache generated in 3.0 s (22.0 MB/s) Eth: New job #ed4217ec from ssl://asia1.ethermine.org:5555; diff: 4000MH Eth: New job #2009407e from ssl://asia1.ethermine.org:5555; diff: 4000MH GPU1: Allocating DAG for epoch #392 (4.06) GB CUDA error in CudaProgram.cu:388 : out of memory (2) GPU1: CUDA memory: 4.00 GB total, 3.25 GB free GPU1 initMiner error: out of memory Fatal error detected. Restarting. Eth speed: 0.000 MH/s, shares: 0/0/0, time: 0:00
Eth: New job #0d4111ed from ssl://asia1.ethermine.org:5555; diff: 4000MH Eth speed: 0.000 MH/s, shares: 0/0/0, time: 0:00
Phoenix Miner 5.5c Windows/msvc - Release build -----------------------------------------------
Waiting 15 s for previous instance to close
Any ideas about what can I do to fix that ?
Thank you
If it`s the wrong place I apologize
Hey guys. I got the same problem with GeForce GTX 1650 on my prestige 14 laptop, someone know how to fix it? :/ Any help is very appreciated, thanks for your time. Cheers
|
|
|
|
buraz11
Jr. Member
Offline
Activity: 115
Merit: 4
|
|
February 12, 2021, 05:19:37 AM |
|
4gb gpus cant mine eth anymore
|
|
|
|
bledos07
Newbie
Offline
Activity: 2
Merit: 0
|
|
February 12, 2021, 08:18:44 AM |
|
Hi guys, which program are you using for tweaking of rx 6800? Thanks
I receive my rx6800 tomorrow It would be a pleasure to share information about the configuration and other matters. I'm going to mount it on in rig amd full: Asus Rog Strix x570-E Gaming. Ryzen 9 3950x 4.7GHz Corsair iCUE H115i rgb PRO XT Alpha AMD DDR4-3200 AsRock RX-6800 PHANTOM Gaming D OC I already have SAM activated to test if it runs at + 80MH / s Hi, I have alredy rx 6800 and i never reach more then 60 Mhs, what about u? Guys can u help me someone, always if I start my Phoenix Miner then my windows system start lagging, it is really anoying, I never had this experience with previous 5700 mining...
|
|
|
|
|