PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[Mullah.Ahmed]

Rig with 5 rx 5700 xt with settings vram clock speed 1800 to 1810, core 1300 to 1350 MHz and voltage 725 to 800 mv , win 10, amd driver ver 20.4.2. Test it at f2pool, ethermine and nicehase. With teamredminer had no problem at all, no problem at all for 5 days continuously. With phoenix miner 5.4c and 5.3b I had the same problem, when the phoenix was starting after a while (from 1 or 2 min to few hours) 1 or 2 gpus they showed 0 mh while the phoenix continued mining with the other gpus without any message and the volt from the gpu that shows 0 Mh drops to 20 watt at the software and about –100 from the wall.
Any idea why it does this and how I can fix it?

yes I have an idea how you can fix it - stick with your teamredminer - continuously.

[markoz]

@phoenixminer

im having trouble when mining on linux with 20.10 drivers on 5700xt. TRM works normal but wht i start your miner i get

GPU5: Allocating buffers failed with: clCreateBuffer (-4).

 -rmode 2 -stales 1 -daglim 0 -eres 0 -rvram 1

[markoz]

@phoenixminer

im having trouble when mining on linux with 20.10 drivers on 5700xt. TRM works normal but wht i start your miner i get

GPU5: Allocating buffers failed with: clCreateBuffer (-4).

 -rmode 2 -stales 1 -daglim 0 -eres 0 -rvram 1

im mining on nanopool. etc works but when i try eth i get this buffer error or "connection closed by pool"

https://imgur.com/vF7vIoU

[drsimkein]

Last week I have moved from claymore to phoenix, so is there a way to run straps or some similarl command to "-strap POL8E8@2250"
ty

[doctorman]

is there a way to be notified by email or something when invalid shares go above certain percentage?

would be a great feature

Do you know how to setup to bi notified when worker is offline?

no, but I am more concerned about getting invalid shares as a high rate due to a mess up on OC or a new EPOCh.

[josh1095]

1 hour in and wow, switching from claymore to phoenix was a breeze. Almost a copy and paste affair. I mean, gotta setup your powershell:startup and paste in some new info but it was super simple and so far, looking good.
I would've never switched but, for whatever reasons, the devs behind claymore must not have written working miner for the DAG increase the other morning(it was a day ago i think).

Just wanted to say thanks

*Rig is running 1 rx580 8g and 7 1060 6Gb cards at a solid 185mH. The 1060s have all been going for 3 years straight by the way. Hardly any failures since i switched to using a rack server type 12v supply. Also, they're $25! super efficient and very very powerful

hello can you give me your oc parameters for 1060 6Gb tdp cclok mclok thank you

No problem.I use Afterburner. Currently my zotac 1060 6gb cards are :   
Power:    65
CPU:       55
Memory: 800

There are a couple cards that can't do 800 memory OC. so a couple are, around 650. I used to have 8 total 1060s, all identical and for a couple years they could handle 850 mem stable.
I keep a box fan on my rig, on low, barely draws any power. Keeps my hottest card below 61. Most are 55 to 57.
Hope this helps.

[devivier]

1 hour in and wow, switching from claymore to phoenix was a breeze. Almost a copy and paste affair. I mean, gotta setup your powershell:startup and paste in some new info but it was super simple and so far, looking good.
I would've never switched but, for whatever reasons, the devs behind claymore must not have written working miner for the DAG increase the other morning(it was a day ago i think).

Just wanted to say thanks

*Rig is running 1 rx580 8g and 7 1060 6Gb cards at a solid 185mH. The 1060s have all been going for 3 years straight by the way. Hardly any failures since i switched to using a rack server type 12v supply. Also, they're $25! super efficient and very very powerful

hello can you give me your oc parameters for 1060 6Gb tdp cclok mclok thank you

No problem.I use Afterburner. Currently my zotac 1060 6gb cards are :   
Power:    65
CPU:       55
Memory: 800

Yes thanks
I have p0 activate and -starps 1 active and I run at 24 mh / s
tdp 55 cclk 75 memory 280
+ - 40 hour validation


There are a couple cards that can't do 800 memory OC. so a couple are, around 650. I used to have 8 total 1060s, all identical and for a couple years they could handle 850 mem stable.
I keep a box fan on my rig, on low, barely draws any power. Keeps my hottest card below 61. Most are 55 to 57.
Hope this helps.

[bobben2]

Do you guys still mining with rx470?
Planning to rebuild this rig. I want to know if still worth mining with rx470.

If someone still mining with this cards can you share your power consumption. Thanks.

Of course you can mine with RX 470.   Mine are doing 30 MH/s.  They are the Sapphire variant with Samsung 8Gb.

[lionkos]

Rig with 5 rx 5700 xt with settings vram clock speed 1800 to 1810, core 1300 to 1350 MHz and voltage 725 to 800 mv , win 10, amd driver ver 20.4.2. Test it at f2pool, ethermine and nicehase. With teamredminer had no problem at all, no problem at all for 5 days continuously. With phoenix miner 5.4c and 5.3b I had the same problem, when the phoenix was starting after a while (from 1 or 2 min to few hours) 1 or 2 gpus they showed 0 mh while the phoenix continued mining with the other gpus without any message and the volt from the gpu that shows 0 Mh drops to 20 watt at the software and about –100 from the wall.
Any idea why it does this and how I can fix it?

yes I have an idea how you can fix it - stick with your teamredminer - continuously.

The thing is that with the same settings and the same watts from the wall, the phoenix has 55.5 mh on each card and the teamred has 54 to 54.3. I have seen that what the miners report in software is also reported in the pools. 1 to 1.5 mh per cart per day for 5 gpu may not say much, but over time it is a significant difference. So if I manage to stabilize phoenix it would be good. Of course I will prefer stability from the few mh above.
So anyone some idea?

[chinh.daongoc]

Does phoenix miner have something like "hashrate watchdog"?

I want to execute reboot.bat when hashrate of any GPU falls below 20MH/s

Thanks

[abrgeza]

Rig with 5 rx 5700 xt with settings vram clock speed 1800 to 1810, core 1300 to 1350 MHz and voltage 725 to 800 mv , win 10, amd driver ver 20.4.2. Test it at f2pool, ethermine and nicehase. With teamredminer had no problem at all, no problem at all for 5 days continuously. With phoenix miner 5.4c and 5.3b I had the same problem, when the phoenix was starting after a while (from 1 or 2 min to few hours) 1 or 2 gpus they showed 0 mh while the phoenix continued mining with the other gpus without any message and the volt from the gpu that shows 0 Mh drops to 20 watt at the software and about –100 from the wall.
Any idea why it does this and how I can fix it?

yes I have an idea how you can fix it - stick with your teamredminer - continuously.

The thing is that with the same settings and the same watts from the wall, the phoenix has 55.5 mh on each card and the teamred has 54 to 54.3. I have seen that what the miners report in software is also reported in the pools. 1 to 1.5 mh per cart per day for 5 gpu may not say much, but over time it is a significant difference. So if I manage to stabilize phoenix it would be good. Of course I will prefer stability from the few mh above.
So anyone some idea?

Don't use cvddc, cclock and mvddc. Set it to 0 for each card and use only mclock and powlim. If you use msi ab use it only for fan control.

-cclock 0,0,0,0,0
-cvddc 0,0,0,0,0
-mclock 1800,1800,1800,1800,1800
-mvddc 0,0,0,0,0
-powlim -40,-40,-40,-40,-40 (some gpu can work with -45 or -50 but some gpu can't work even wit -40)

[dubignyp]

@al3rbee and @AL4HA error. 1080 Ti = 32 Mh/h

[wizwiz316]

Hi newbie here,

I have just tried to run the PhenoixMiner and got this error can anyone help me fix it?

Phoenix Miner 5.4c Windows/msvc - Release build
-----------------------------------------------

Waiting 15 s for previous instance to close
CUDA version: 11.0, CUDA runtime: 8.0
No OpenCL platforms found
Available GPUs for mining:
GPU1: GeForce GTX 1050 Ti (pcie 1), CUDA cap. 6.1, 4 GB VRAM, 6 CUs
Nvidia driver version: 460.89
Eth: Loading pools from epools.txt
Eth: the pool list contains 3 pools (0 from command-line)
Eth: primary pool: eu1.ethermine.org:4444
Starting GPU mining
Eth: Connecting to ethash pool eu1.ethermine.org:4444 (proto: EthProxy)
GPU1: 40C 0% 24W
GPUs power: 23.5 W
Eth: Connected to ethash pool eu1.ethermine.org:4444 (172.65.207.xxx)
Eth: New job #18430768 from eu1.ethermine.org:4444; diff: 4000MH
GPU1: Starting up... (0)
GPU1: Generating ethash light cache for epoch #383
Listening for CDM remote manager at port 3333 in read-only mode
Eth: New job #d715a735 from eu1.ethermine.org:4444; diff: 4000MH
Light cache generated in 4.4 s (14.6 MB/s)
GPU1: Allocating DAG (4.01) GB; good for epoch up to #385
CUDA error in CudaProgram.cu:388 : out of memory (2)
GPU1: CUDA memory: 4.00 GB total, 3.30 GB free
GPU1 initMiner error: out of memory
Fatal error detected. Restarting.
Eth speed: 0.000 MH/s, shares: 0/0/0, time: 0:00
Eth: New job #3f576799 from eu1.ethermine.org:4444; diff: 4000MH
Eth: New job #b691a7b3 from eu1.ethermine.org:4444; diff: 4000MH



Eth: New job #13ca4a33 from eu1.ethermine.org:4444; diff: 4000MH
Eth speed: 0.000 MH/s, shares: 0/0/0, time: 0:00



Thanks

[abg00]

Does phoenix miner have something like "hashrate watchdog"?

I want to execute reboot.bat when hashrate of any GPU falls below 20MH/s

Thanks

-minrigspeed option

[Wisbrown]

What is the level of its security and its network.

[sirgod]

Hello guys, i have 5 gtx 1080ti and im getting 210MH/s (42MH/s each and consuming 160w each) with power75% +50 +650 clocksettings. im just using the miner and the PILL, and basically 0 configs
Any hints to pump these rookie numbers ?  

[lionkos]

Rig with 5 rx 5700 xt with settings vram clock speed 1800 to 1810, core 1300 to 1350 MHz and voltage 725 to 800 mv , win 10, amd driver ver 20.4.2. Test it at f2pool, ethermine and nicehase. With teamredminer had no problem at all, no problem at all for 5 days continuously. With phoenix miner 5.4c and 5.3b I had the same problem, when the phoenix was starting after a while (from 1 or 2 min to few hours) 1 or 2 gpus they showed 0 mh while the phoenix continued mining with the other gpus without any message and the volt from the gpu that shows 0 Mh drops to 20 watt at the software and about –100 from the wall.
Any idea why it does this and how I can fix it?

yes I have an idea how you can fix it - stick with your teamredminer - continuously.

The thing is that with the same settings and the same watts from the wall, the phoenix has 55.5 mh on each card and the teamred has 54 to 54.3. I have seen that what the miners report in software is also reported in the pools. 1 to 1.5 mh per cart per day for 5 gpu may not say much, but over time it is a significant difference. So if I manage to stabilize phoenix it would be good. Of course I will prefer stability from the few mh above.
So anyone some idea?

Don't use cvddc, cclock and mvddc. Set it to 0 for each card and use only mclock and powlim. If you use msi ab use it only for fan control.

-cclock 0,0,0,0,0
-cvddc 0,0,0,0,0
-mclock 1800,1800,1800,1800,1800
-mvddc 0,0,0,0,0
-powlim -40,-40,-40,-40,-40 (some gpu can work with -45 or -50 but some gpu can't work even wit -40)

Thanks for the reply.
I do not use any of them in the bat file. For gpu control I use only AMD software. In the bat file I have only the main points such as pool, wallet and worker. The power limit of all gpus is at 0%. Should I add clock, cvddc and mvddc at bat file with 0?

[Deafran]

Do you guys still mining with rx470?
Planning to rebuild this rig. I want to know if still worth mining with rx470.

If someone still mining with this cards can you share your power consumption. Thanks.

using ethOS, RX 470 4GB

ram amount:     3.7G   used: 3.5G   free: 219M
cpu usage / temp / load: 95.2% / 50C / 2.54 2.14 1.17

53°C  Fan: 2.7    Hash: 22.03    03 Ellesmere RX 470 113-WE353FU-M73 Samsung
57°C  Fan: 2.8    Hash: 22.01    05 Ellesmere RX 470 113-WE353FU-M73 Samsung
57°C  Fan: 2.8    Hash: 22.02    09 Ellesmere RX 470 113-WE353FU-M73 Samsung
57°C  Fan: 2.8    Hash: 22.03    0a Ellesmere RX 470 113-WE353FU-M73 Samsung
48°C  Fan: 2.7    Hash: 22.03    0b Ellesmere RX 470 113-WE353FU-M73 Samsung
57°C  Fan: 2.8    Hash: 22.03    0c Ellesmere RX 470 113-WE353FU-M73 Samsung
50°C  Fan: 2.7    Hash: 22.03    0d Ellesmere RX 470 113-WE353FU-M73 Samsung
54°C  Fan: 2.8    Hash: 22.03    0e Ellesmere RX 470 113-WE353FU-M73 Samsung

176.2 hash: miner active


GPU1: 52C 80% 84W, GPU2: 56C 80% 88W, GPU3: 57C 80% 85W, GPU4: 57C 80% 84W, GPU5: 48C 80% 84W, GPU6: 57C 80% 85W, GPU7: 50C 80% 85W, GPU8: 53C 80% 81W
GPUs power: 676.0 W
Eth: New job #e652962b from eth-asia1.nanopool.org:9999; diff: 10000MH
Eth: New job #10c86f7b from eth-asia1.nanopool.org:9999; diff: 10000MH
Eth speed: 176.210 MH/s, shares: 5/0/0, time: 0:06
GPUs: 1: 22.030 MH/s (0) 2: 22.015 MH/s (0) 3: 22.020 MH/s (0) 4: 22.029 MH/s (1) 5: 22.035 MH/s (1) 6: 22.029 MH/s (0) 7: 22.033 MH/s (1) 8: 22.019 MH/s (2)

Hi newbie here,

I have just tried to run the PhenoixMiner and got this error can anyone help me fix it?

Phoenix Miner 5.4c Windows/msvc - Release build
-----------------------------------------------

Waiting 15 s for previous instance to close
CUDA version: 11.0, CUDA runtime: 8.0
No OpenCL platforms found
Available GPUs for mining:
GPU1: GeForce GTX 1050 Ti (pcie 1), CUDA cap. 6.1, 4 GB VRAM, 6 CUs
Nvidia driver version: 460.89
Eth: Loading pools from epools.txt
Eth: the pool list contains 3 pools (0 from command-line)
Eth: primary pool: eu1.ethermine.org:4444
Starting GPU mining
Eth: Connecting to ethash pool eu1.ethermine.org:4444 (proto: EthProxy)
GPU1: 40C 0% 24W
GPUs power: 23.5 W
Eth: Connected to ethash pool eu1.ethermine.org:4444 (172.65.207.xxx)
Eth: New job #18430768 from eu1.ethermine.org:4444; diff: 4000MH
GPU1: Starting up... (0)
GPU1: Generating ethash light cache for epoch #383
Listening for CDM remote manager at port 3333 in read-only mode
Eth: New job #d715a735 from eu1.ethermine.org:4444; diff: 4000MH
Light cache generated in 4.4 s (14.6 MB/s)
GPU1: Allocating DAG (4.01) GB; good for epoch up to #385
CUDA error in CudaProgram.cu:388 : out of memory (2)
GPU1: CUDA memory: 4.00 GB total, 3.30 GB free
GPU1 initMiner error: out of memory
Fatal error detected. Restarting.
Eth speed: 0.000 MH/s, shares: 0/0/0, time: 0:00
Eth: New job #3f576799 from eu1.ethermine.org:4444; diff: 4000MH
Eth: New job #b691a7b3 from eu1.ethermine.org:4444; diff: 4000MH



Eth: New job #13ca4a33 from eu1.ethermine.org:4444; diff: 4000MH
Eth speed: 0.000 MH/s, shares: 0/0/0, time: 0:00



Thanks

try this :

-dagrestart 2 -gser 2

[abrgeza]

Rig with 5 rx 5700 xt with settings vram clock speed 1800 to 1810, core 1300 to 1350 MHz and voltage 725 to 800 mv , win 10, amd driver ver 20.4.2. Test it at f2pool, ethermine and nicehase. With teamredminer had no problem at all, no problem at all for 5 days continuously. With phoenix miner 5.4c and 5.3b I had the same problem, when the phoenix was starting after a while (from 1 or 2 min to few hours) 1 or 2 gpus they showed 0 mh while the phoenix continued mining with the other gpus without any message and the volt from the gpu that shows 0 Mh drops to 20 watt at the software and about –100 from the wall.
Any idea why it does this and how I can fix it?

yes I have an idea how you can fix it - stick with your teamredminer - continuously.

The thing is that with the same settings and the same watts from the wall, the phoenix has 55.5 mh on each card and the teamred has 54 to 54.3. I have seen that what the miners report in software is also reported in the pools. 1 to 1.5 mh per cart per day for 5 gpu may not say much, but over time it is a significant difference. So if I manage to stabilize phoenix it would be good. Of course I will prefer stability from the few mh above.
So anyone some idea?

Don't use cvddc, cclock and mvddc. Set it to 0 for each card and use only mclock and powlim. If you use msi ab use it only for fan control.

-cclock 0,0,0,0,0
-cvddc 0,0,0,0,0
-mclock 1800,1800,1800,1800,1800
-mvddc 0,0,0,0,0
-powlim -40,-40,-40,-40,-40 (some gpu can work with -45 or -50 but some gpu can't work even wit -40)

Thanks for the reply.
I do not use any of them in the bat file. For gpu control I use only AMD software. In the bat file I have only the main points such as pool, wallet and worker. The power limit of all gpus is at 0%. Should I add clock, cvddc and mvddc at bat file with 0?

set all to default in amd software and add settings in bat file, maybe amd software cause problems.
PM5.3b and 20.4.2 drivers should work fine.
if it doesn't work use trm or lolminer.

[Vladegg]

Does phoenix miner have something like "hashrate watchdog"?

I want to execute reboot.bat when hashrate of any GPU falls below 20MH/s

Thanks

Try this https://bitcointalk.org/index.php?topic=2071108.0

Working still.