bgibso01
Legendary
Offline
Activity: 1218
Merit: 1001
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 02:34:25 AM |
|
Can anyone tell me how much watts I'm using if on the advanced tab it's roughly showing 1460W? Also, anyone running a lot of TH with the Neptune?
I've got a little over 7th of neptunes running. Several bad cubes laying around. I haven't been able to figure out where all the excess watts would be coming from either. I'm sure that's showing chip level, but I run 220v so I don't have a kill-a-watt meter for the wall watts.
|
|
|
|
Phoenix1969
Legendary
Offline
Activity: 938
Merit: 1000
LIR DEV
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 03:04:16 AM |
|
Can anyone tell me how much watts I'm using if on the advanced tab it's roughly showing 1460W? Also, anyone running a lot of TH with the Neptune?
I didn't bring my crystal ball.... darnit!
|
|
|
|
Phoenix1969
Legendary
Offline
Activity: 938
Merit: 1000
LIR DEV
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 03:06:16 AM |
|
Someone already got this problem ? Seem that one of my 5 cube doesnt receive power as the others... My 4 cubes are at 240 W + and cube 2 is always at 6-7 watts... ? Ive tried all possible combinaisons and i noticed that's really the problem of this cube and not wires. Thank you
I would say take the ribbon cords out from the controller board one by one until you figure out what cord belongs to that cube. Then i would say unplug the rest of the cubes the same way and only leave that one cube plugged in. Then i would say turn it on and mine and see if its still doing it. If it is, then try the power cord from a known working cube and if its still doing it. Then try a ribbon cord from a known working cube and if its still doing it. Try a different slot for the ribbon cord on the controller board. And if its still doing it then email knc for RMA after you have reflashed the micro sd card with firmware from scratch and the problem still exists. If it at some point in the trial it starts working then you know it has to do with that part. My initial guess would be a power issue. I tried everything and ive noticed thats really a power problem of this cube. Does someone have a home solution? If not, gonna need to deal with Knc to get a new one :S Then rip the band aid off and RMA it. Some of mine arrive back today. Thats a turnaround of less then two weeks. support@kncminer.comOMG congrats dude. That's usually unheard of in here.... thanks for the info... What Country?
|
|
|
|
LongAndShort
Legendary
Offline
Activity: 1078
Merit: 1050
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 06:06:56 AM Last edit: April 13, 2015, 09:39:28 AM by LongAndShort |
|
Someone already got this problem ? Seem that one of my 5 cube doesnt receive power as the others... My 4 cubes are at 240 W + and cube 2 is always at 6-7 watts... ? Ive tried all possible combinaisons and i noticed that's really the problem of this cube and not wires. Thank you
I would say take the ribbon cords out from the controller board one by one until you figure out what cord belongs to that cube. Then i would say unplug the rest of the cubes the same way and only leave that one cube plugged in. Then i would say turn it on and mine and see if its still doing it. If it is, then try the power cord from a known working cube and if its still doing it. Then try a ribbon cord from a known working cube and if its still doing it. Try a different slot for the ribbon cord on the controller board. And if its still doing it then email knc for RMA after you have reflashed the micro sd card with firmware from scratch and the problem still exists. If it at some point in the trial it starts working then you know it has to do with that part. My initial guess would be a power issue. I tried everything and ive noticed thats really a power problem of this cube. Does someone have a home solution? If not, gonna need to deal with Knc to get a new one :S Then rip the band aid off and RMA it. Some of mine arrive back today. Thats a turnaround of less then two weeks. support@kncminer.comOMG congrats dude. That's usually unheard of in here.... thanks for the info... What Country? Australia. All the cubes work as intended as they did the day i bought them all... For now
|
|
|
|
teslaman
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 65
Merit: 15
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 09:17:53 AM |
|
Can anyone tell me how much watts I'm using if on the advanced tab it's roughly showing 1460W? Also, anyone running a lot of TH with the Neptune?
Based on the calculations done on the R.I.P. KnC forum, I would say that's roughly around 1982W at the wall. I used the same calculations to see if I could run 3 Neptune miners on one 30A, 240V breaker and it came out right around the recommended max 80% load. I went ahead and did it and it worked out fine. So, the numbers can't be too far off. I also use it for calculating how much of the electric bill the miners account for. Subtracting the miners puts me around what the average usage was pre-mining. If I ever get a clamp meter, I'll be sure to post how the actual numbers compare. ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
notthematrix
Legendary
Offline
Activity: 980
Merit: 1000
CryptoTalk.Org - Get Paid for every Post!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 05:50:56 PM |
|
Can anyone tell me how much watts I'm using if on the advanced tab it's roughly showing 1460W? Also, anyone running a lot of TH with the Neptune?
Based on the calculations done on the R.I.P. KnC forum, I would say that's roughly around 1982W at the wall. I used the same calculations to see if I could run 3 Neptune miners on one 30A, 240V breaker and it came out right around the recommended max 80% load. I went ahead and did it and it worked out fine. So, the numbers can't be too far off. I also use it for calculating how much of the electric bill the miners account for. Subtracting the miners puts me around what the average usage was pre-mining. If I ever get a clamp meter, I'll be sure to post how the actual numbers compare. ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I pull around +/- 1900 watt @ all 500 mhz knc defaults with 470 mhz so running ~1900w at @ 500 is quite good.
|
|
|
|
notthematrix
Legendary
Offline
Activity: 980
Merit: 1000
CryptoTalk.Org - Get Paid for every Post!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 05:53:54 PM |
|
Someone already got this problem ? Seem that one of my 5 cube doesnt receive power as the others... My 4 cubes are at 240 W + and cube 2 is always at 6-7 watts... ? Ive tried all possible combinaisons and i noticed that's really the problem of this cube and not wires. Thank you
I would say take the ribbon cords out from the controller board one by one until you figure out what cord belongs to that cube. Then i would say unplug the rest of the cubes the same way and only leave that one cube plugged in. Then i would say turn it on and mine and see if its still doing it. If it is, then try the power cord from a known working cube and if its still doing it. Then try a ribbon cord from a known working cube and if its still doing it. Try a different slot for the ribbon cord on the controller board. And if its still doing it then email knc for RMA after you have reflashed the micro sd card with firmware from scratch and the problem still exists. If it at some point in the trial it starts working then you know it has to do with that part. My initial guess would be a power issue. I tried everything and ive noticed thats really a power problem of this cube. Does someone have a home solution? If not, gonna need to deal with Knc to get a new one :S Then rip the band aid off and RMA it. Some of mine arrive back today. Thats a turnaround of less then two weeks. support@kncminer.comOMG congrats dude. That's usually unheard of in here.... thanks for the info... What Country? Australia. All the cubes work as intended as they did the day i bought them all... For now RMA at KNC works quite well its the scammers who do not have a miner at all that PRETEND to have a miner and create the messages about failing parts at forums like theese.
|
|
|
|
bbuser
Newbie
Offline
Activity: 34
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 07:00:01 PM |
|
I've got a little over 7th of neptunes running. Several bad cubes laying around. I haven't been able to figure out where all the excess watts would be coming from either. I'm sure that's showing chip level, but I run 220v so I don't have a kill-a-watt meter for the wall watts.
I didn't bring my crystal ball.... darnit!
Based on the calculations done on the R.I.P. KnC forum, I would say that's roughly around 1982W at the wall. I used the same calculations to see if I could run 3 Neptune miners on one 30A, 240V breaker and it came out right around the recommended max 80% load. I went ahead and did it and it worked out fine. So, the numbers can't be too far off. I also use it for calculating how much of the electric bill the miners account for. Subtracting the miners puts me around what the average usage was pre-mining. If I ever get a clamp meter, I'll be sure to post how the actual numbers compare. ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I pull around +/- 1900 watt @ all 500 mhz knc defaults with 470 mhz so running ~1900w at @ 500 is quite good.
Thanks guys. I'm assuming everyone is also running fans with these miners, right? I've got a fan but it uses like 84watts. Any recommendations on high efficiency fans?
|
|
|
|
notthematrix
Legendary
Offline
Activity: 980
Merit: 1000
CryptoTalk.Org - Get Paid for every Post!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 13, 2015, 08:27:36 PM |
|
I've got a little over 7th of neptunes running. Several bad cubes laying around. I haven't been able to figure out where all the excess watts would be coming from either. I'm sure that's showing chip level, but I run 220v so I don't have a kill-a-watt meter for the wall watts.
I didn't bring my crystal ball.... darnit!
Based on the calculations done on the R.I.P. KnC forum, I would say that's roughly around 1982W at the wall. I used the same calculations to see if I could run 3 Neptune miners on one 30A, 240V breaker and it came out right around the recommended max 80% load. I went ahead and did it and it worked out fine. So, the numbers can't be too far off. I also use it for calculating how much of the electric bill the miners account for. Subtracting the miners puts me around what the average usage was pre-mining. If I ever get a clamp meter, I'll be sure to post how the actual numbers compare. ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I pull around +/- 1900 watt @ all 500 mhz knc defaults with 470 mhz so running ~1900w at @ 500 is quite good.
Thanks guys. I'm assuming everyone is also running fans with these miners, right? I've got a fan but it uses like 84watts. Any recommendations on high efficiency fans? just replaced the fanes of the bonus miners. with a noctua 3000 rpm fan 4 wire fan. and a room with an open chimney.
|
|
|
|
teslaman
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 65
Merit: 15
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 07:17:11 AM |
|
Thanks guys. I'm assuming everyone is also running fans with these miners, right? I've got a fan but it uses like 84watts. Any recommendations on high efficiency fans?
I wasn't running any during the winter, but I am now that it's getting warmer here. I'm not sure how much luck you'll have trying to find a high efficiency fan that has good airflow. Usually, you just size it to your needs, how big you want/need it, how much air you need it to move, etc, then find a brand with good reviews. I just ended up getting a 20" Box fan to blow the heat out the window and that is working well for my 3 Neptunes. That's moving a lot of air though, so it's rated at 120W or so on High. That only costs me less than $10 a month to run 24/7 though, so I can definitely live with that. Is yours moving a good amount of air at 84W?
|
|
|
|
Hunyadi
Legendary
Offline
Activity: 1281
Merit: 1000
☑ ♟ ☐ ♚
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 08:58:40 AM |
|
3 out of 4 dies of one 1st batch Titan-cube died o while a go. Do you guys have any tricks to bring them back? I can't remember how to exactly power cycle them. Was it to just start the miner without the power cable or something like that?
|
▂▃▅▇█▓▒░B**-Cultist░▒▓█▇▅▃▂
|
|
|
mishax1
Legendary
Offline
Activity: 2898
Merit: 1017
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 10:27:30 AM |
|
3 out of 4 dies of one 1st batch Titan-cube died o while a go. Do you guys have any tricks to bring them back? I can't remember how to exactly power cycle them. Was it to just start the miner without the power cable or something like that?
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
|
|
|
|
Hunyadi
Legendary
Offline
Activity: 1281
Merit: 1000
☑ ♟ ☐ ♚
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 10:44:39 AM |
|
3 out of 4 dies of one 1st batch Titan-cube died o while a go. Do you guys have any tricks to bring them back? I can't remember how to exactly power cycle them. Was it to just start the miner without the power cable or something like that?
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$ Yes they stopped working around 2 weeks ago. I updated fw to 2.0 and it helped, unfortunately, now nothing seems to work.
|
▂▃▅▇█▓▒░B**-Cultist░▒▓█▇▅▃▂
|
|
|
cryptodevil
Legendary
Offline
Activity: 2240
Merit: 1254
Thread-puller extraordinaire
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 11:02:06 AM |
|
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
Careful, you'll invoke that twat notthematrix to start posting his sermon about how everybody who complains about KnC is an idiot who isn't deserving of KnC's love and how he took a gamble and won while everybody who didn't win is an asshole who took a gamble and lost so, you know, stfu dumb bitches . . .etc. etc.
|
WARNING!!! Check your forum URLs carefully and avoid links to phishing sites like 'thebitcointalk' 'bitcointalk.to' and 'BitcointaLLk'
|
|
|
notthematrix
Legendary
Offline
Activity: 980
Merit: 1000
CryptoTalk.Org - Get Paid for every Post!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 01:17:13 PM |
|
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
Careful, you'll invoke that twat notthematrix to start posting his sermon about how everybody who complains about KnC is an idiot who isn't deserving of KnC's love and how he took a gamble and won while everybody who didn't win is an asshole who took a gamble and lost so, you know, stfu dumb bitches . . .etc. etc. exactly you r getting it. Its just like the insiders of banks... https://ipsofactodotme.wordpress.com/2015/03/05/dit-kan-niet-waar-zijn-this-cant-be-true/if yoiu are not tech shavvy , you are a muppet , and muppets sould not take the gamble , but if you can replace a beagle bone black , its quite easy to restart the miner , go for beagle bone black rev C (for neptune) and you can find how to re-flash it in previous posts.... if done restore the settings and you are online again. saw some titan boards with raspberry pi if yours have a raspberry you can also replace that easaly.
|
|
|
|
Hunyadi
Legendary
Offline
Activity: 1281
Merit: 1000
☑ ♟ ☐ ♚
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 01:22:30 PM |
|
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
Careful, you'll invoke that twat notthematrix to start posting his sermon about how everybody who complains about KnC is an idiot who isn't deserving of KnC's love and how he took a gamble and won while everybody who didn't win is an asshole who took a gamble and lost so, you know, stfu dumb bitches . . .etc. etc. exactly you r getting it. Its just like the insiders of banks... https://ipsofactodotme.wordpress.com/2015/03/05/dit-kan-niet-waar-zijn-this-cant-be-true/if yoiu are not tech shavvy , you are a muppet , and muppets sould not take the gamble , but if you can replace a beagle bone black , its quite easy to restart the miner , go for beagle bone black rev C (for neptune) and you can find how to re-flash it in previous posts.... if done restore the settings and you are online again. ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) Re-flashin is not a problem. The problem is, it doesn't work.
|
▂▃▅▇█▓▒░B**-Cultist░▒▓█▇▅▃▂
|
|
|
notthematrix
Legendary
Offline
Activity: 980
Merit: 1000
CryptoTalk.Org - Get Paid for every Post!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 01:27:46 PM |
|
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
Careful, you'll invoke that twat notthematrix to start posting his sermon about how everybody who complains about KnC is an idiot who isn't deserving of KnC's love and how he took a gamble and won while everybody who didn't win is an asshole who took a gamble and lost so, you know, stfu dumb bitches . . .etc. etc. exactly you r getting it. Its just like the insiders of banks... https://ipsofactodotme.wordpress.com/2015/03/05/dit-kan-niet-waar-zijn-this-cant-be-true/if yoiu are not tech shavvy , you are a muppet , and muppets sould not take the gamble , but if you can replace a beagle bone black , its quite easy to restart the miner , go for beagle bone black rev C (for neptune) and you can find how to re-flash it in previous posts.... if done restore the settings and you are online again. ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) Re-flashin is not a problem. The problem is, it doesn't work. what Does not work? ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) .... The beagle bone , the board youy cant see the cubes etc .... no electicity etc etc ,, so thats what you have to check..... I did the same. you can RMA it only if cubes are realy broken. but for the board its easy to fix. make a puic of the controler board so people can see what Micro computer is on it.
|
|
|
|
Hunyadi
Legendary
Offline
Activity: 1281
Merit: 1000
☑ ♟ ☐ ♚
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 01:34:37 PM |
|
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
Careful, you'll invoke that twat notthematrix to start posting his sermon about how everybody who complains about KnC is an idiot who isn't deserving of KnC's love and how he took a gamble and won while everybody who didn't win is an asshole who took a gamble and lost so, you know, stfu dumb bitches . . .etc. etc. exactly you r getting it. Its just like the insiders of banks... https://ipsofactodotme.wordpress.com/2015/03/05/dit-kan-niet-waar-zijn-this-cant-be-true/if yoiu are not tech shavvy , you are a muppet , and muppets sould not take the gamble , but if you can replace a beagle bone black , its quite easy to restart the miner , go for beagle bone black rev C (for neptune) and you can find how to re-flash it in previous posts.... if done restore the settings and you are online again. ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) Re-flashin is not a problem. The problem is, it doesn't work. what Does not work? ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) .... The beagle bone , the board youy cant see the cubes etc .... no electicity etc etc ,, so thats what you have to check..... I did the same. you can RMA it only if cubes are realy broken. but for the board its easy to fix. make a puic of the controler board so people can see what Micro computer is on it. 3 out of 4 dies of one 1st batch Titan-cube died o while a go. Do you guys have any tricks to bring them back? I can't remember how to exactly power cycle them. Was it to just start the miner without the power cable or something like that?
|
▂▃▅▇█▓▒░B**-Cultist░▒▓█▇▅▃▂
|
|
|
Prelude
Legendary
Offline
Activity: 1596
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 02:04:06 PM |
|
I'm possibly picking up a used bonus Neptune, and my understanding is they were shipped without the VRM heat transfer pads that were factory installed on the original Neptunes and Titans. Has anyone found a suitable replacement for them? I assume they're needed for stable operation at 3~3.3 TH/s? I also need to RMA a Titan cube that has 2 dead dies. Also have another cube with 1 dead die, but KNC won't RMA that one since I can overclock my cubes to reach 300MH/s anyways. ![Roll Eyes](https://bitcointalk.org/Smileys/default/rolleyes.gif) What kind of turn around times have you guys experienced lately with Titan cube RMAs?
|
|
|
|
s1gs3gv
Legendary
Offline
Activity: 1316
Merit: 1014
ex uno plures
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 14, 2015, 02:49:37 PM |
|
Oh god, do they just stop working even after all the firmware updates ? who else experience this ? can't believe they sent alpha state miners for 10,000$
Careful, you'll invoke that twat notthematrix to start posting his sermon about how everybody who complains about KnC is an idiot who isn't deserving of KnC's love and how he took a gamble and won while everybody who didn't win is an asshole who took a gamble and lost so, you know, stfu dumb bitches . . .etc. etc. +1
|
|
|
|
|