The problem doesn't lie in struggling to make constructive posts the problem is in putting forth the effort to learn enough to make a contribution to the forum that people find constructive.
They are free to post in local boards until such a time that the poster can make a coherent English sentence, it doesn't have to be perfect but should get the idea across.
Also if the Junior member is just here to "earn" then they will be stuck where they belong. Earning here is a privilege not a right.


This is designed to allow the Merit system to outlive it's initial launch. Other than Merit sources you will need to be deemed a quality poster by the community to have the privilege to send out merit. You can always nominate someone else in the threads offering Merit for quality if you really think they deserve it


I think you are trying to say that the higher ranked members should be sending Merits to lower ranked members??? If so they do when they feel a post has earned it. They also send it to high ranked members. That's the system at play, if anyone feels a post is "quality" in their mind then they can send Merit.


I broke it down into parts and went with what I thought they meant. No one but OP really know what they meant and it will probably be a while before they can clearly explain it to us

Hi there,

Anyone who was scammed should proceed to open up a scam accusation against the account involved. You can do so here

https://bitcointalk.org/index.php?board=83.0

Make sure to include your PM's and any other information you have to prove your case. If it appears to have been a scam a DT member will usually come along and tag OP as their tags are more visible to the community.
Also tag them with your feedback, as some people ( Not enough people) do actually read these.

As a rule of thumb you should always use Escrow, the cost may not seem worth it but then you see a case like this that serves as a reminder.

Good call

I think you can I remember reading about it somewhere. The problem lies in the fact that you can't daisy chain in any other Miners. I might be wrong but That's how I remember it being laid out.

What's the problem is your AUC3 defective?

Here is the hardware thread on the 841; HAggs has had some training at Canaan and may be able to shed more light on that question.

https://bitcointalk.org/index.php?topic=3191702.0

Which way is the air exhausting out of the unit? I don't have an 841 but I think they still exhaust the same as the 741, air leaves on the fan side.

I remember a few units that had the fan installed backwards, from previous generations. Now it doesn't explain the fan RPM changing especially if the speed is set at minimum of 100. EDIT: although the backpressure from pushing through the unit as opposed to pulling through might affect the RPM that the fan can spin at.

Just something to check on before swapping fans out. If it is the fan it's a simple fix of removing the shroud and flipping it around.

When something like that happens. Check the miner status page.

This will tell you if you are still hashing away and whether or not you are on your primary/secondary or tertiary pool.

Mine on

You should inquire in the active thread for the dragonmint.

bitcointalk.org/index.php?topic=2443327.1800

I think some people have received some but the information about the product and company is patchy at best.

BTC talk name: Steamtyme
Rank: Full member
Post count: 767
Btw address: 3L13YFDBYjF87xBUde7wV97yA1C2AyM5EN
Wear signature: yes

Will you accept trusted forum escrow?

Are there any restrictions on the $450?

I would offer 20% of face value I would cover the escrow fees

EDIT: found what I needed. Offer retracted

Just a note the specs are different from the 741 to the 841.

Safe operating temp was up to 40C for the 741's

The 841's say up to 30C for the ambient air temp.

So there are differences to be aware of with the new equipment.

Are you accepting escrow?

Hey Phil

I haven't checked in a while what would your escrow fee be on something like the 420 coupon.

Thanks

Looking at your fan intake temperature it looks like your shop is a little warm to begin with. The specs call for intake air temp of 30C ad the high.

You also might be short circuiting the exhaust air to the intake. You might need to look at a better way to exhaust the heat or atleast circulate the air throughout the shop.

Are you using the same controller (PI) The 841's have a different controller firmware that needs to be flashed onto the PI.

Also if you do have that set properly, did you try switching the cables around you are using to Daisy Chain them, it might be that the first one in the chain is defective. This was just a guess because I don't think the miner lights would be green if this was the case. EDIt: Got my colours switched up might be the cable since this is "idle"

Can you provide proof of ownership of the coupons?

Are you willing to accept forum approved escrow?

Well I feel dumb

This solved my issue, for whatever reason last night I didn't try just running it not as administrator. As soon as I read it I facepalmed.

Anyways running now as expected.

That makes more sense; to me it read you hadn't received them yet. They are great machines.

Thanks, I've updated the wallet and will give Hive another go tonight. I don't like to pass up the opportunity to learn something; can you tell me what blue the commands mean?

OP clearly stated 1 post per reply for review.

When submitting to these services it is best to read and fully understand their rules for submitting.

Here I was excited that maybe someone was going to post on topic, and maybe even comment on my idea. Oh woe is me.

And did they really do anything wrong the posts were all a reasonable amount in different topics that each one found value in.

It just looks like they frequent the same threads and areas and like the posts that try and curb all the shit pilling up in the forum.