ct1aic
|
|
April 07, 2014, 08:41:03 AM |
|
.... snip ....
Thats odd, it seems that there are some changes to a few files that it does not like. It can easly be fixed though, do this;- cd /opt/minepeon git checkout bin/scripts/FactoryReset.sh git bin/bitstreams/README git pull I will try to work out what I did wrong! Neil One of the commands was not recognized... [minepeon@minepeon ~]$ cd /opt/minepeon [minepeon@minepeon minepeon]$ git checkout bin/scripts/FactoryReset.sh [minepeon@minepeon minepeon]$ git bin/bitstreams/README git: 'bin/bitstreams/README' is not a git command. See 'git --help'.[minepeon@minepeon minepeon]$ git pull remote: Counting objects: 27, done. remote: Compressing objects: 100% (26/26), done. remote: Total 27 (delta 6), reused 0 (delta 0) Unpacking objects: 100% (27/27), done. From https://github.com/MineForeman/minepeon-base 93b1f75..dfdac8b master -> origin/master 23c2dbe..61fee71 0.3.0 -> origin/0.3.0 Updating 93b1f75..dfdac8b error: The following untracked working tree files would be overwritten by merge: bin/bitstreams/README Please move or remove them before you can merge. Aborting [minepeon@minepeon minepeon]$ I did a dir and the file is there (as a file): [minepeon@minepeon ~]$ cd /opt/minepeon [minepeon@minepeon minepeon]$ cd bin/bitstreams [minepeon@minepeon bitstreams]$ dir COPYING_fpgaminer README fpgaminer_top_fixed7_197MHz.ncd [minepeon@minepeon bitstreams]$
inside text of README: You must put the file fpgaminer_top_fixed7_197MHz.ncd in here for modminer to w$
|
Rui Costa, Portugal - BTC : 1ct1aicGoUVpZeovsw3cCcPJZJHV5JXtW
|
|
|
kano
Legendary
Offline
Activity: 4592
Merit: 1851
Linux since 1997 RedHat 4
|
|
April 07, 2014, 11:00:30 AM |
|
... inside text of README: You must put the file fpgaminer_top_fixed7_197MHz.ncd in here for modminer to w$
Due to the pointlessness of mining BTC with FPGA, Con removed it since it was the largest file in the distribution and took up about 50% of the file space for everyone downloading cgminer but almost no one uses it - my MMQ sits with my other FPGA quietly watching my ASICs Just get it from a release before it was removed i.e. 3.12.3 or earlier (8-Feb-2014)
|
|
|
|
ct1aic
|
|
April 07, 2014, 11:49:13 AM |
|
... inside text of README: You must put the file fpgaminer_top_fixed7_197MHz.ncd in here for modminer to w$
Due to the pointlessness of mining BTC with FPGA, Con removed it since it was the largest file in the distribution and took up about 50% of the file space for everyone downloading cgminer but almost no one uses it - my MMQ sits with my other FPGA quietly watching my ASICs Just get it from a release before it was removed i.e. 3.12.3 or earlier (8-Feb-2014) As you can see in my last post, it is still there... [minepeon@minepeon minepeon]$ cd bin/bitstreams [minepeon@minepeon bitstreams]$ dir COPYING_fpgaminer README fpgaminer_top_fixed7_197MHz.ncd
|
Rui Costa, Portugal - BTC : 1ct1aicGoUVpZeovsw3cCcPJZJHV5JXtW
|
|
|
KyrosKrane
|
|
April 07, 2014, 11:59:35 AM |
|
.... snip ....
Thats odd, it seems that there are some changes to a few files that it does not like. It can easly be fixed though, do this;- cd /opt/minepeon git checkout bin/scripts/FactoryReset.sh git bin/bitstreams/README git pull I will try to work out what I did wrong! Neil I think Neil missed the word "checkout" in the second command: cd /opt/minepeon git checkout bin/scripts/FactoryReset.sh git checkout bin/bitstreams/README git pull The idea being, your git pull command is being blocked because it doesn't like something about those two files. If you check out both those files, you should be able to do a git pull successfully, until Neil can figure out and fix the real root cause.
|
|
|
|
ct1aic
|
|
April 07, 2014, 01:19:48 PM |
|
.... snip ....
Thats odd, it seems that there are some changes to a few files that it does not like. It can easly be fixed though, do this;- cd /opt/minepeon git checkout bin/scripts/FactoryReset.sh git bin/bitstreams/README git pull I will try to work out what I did wrong! Neil I think Neil missed the word "checkout" in the second command: cd /opt/minepeon git checkout bin/scripts/FactoryReset.sh git checkout bin/bitstreams/README git pull The idea being, your git pull command is being blocked because it doesn't like something about those two files. If you check out both those files, you should be able to do a git pull successfully, until Neil can figure out and fix the real root cause. Greetings, KyrosKrane. It didn't worked, but as it's a file with no need to be there, I removed it and it worked! [minepeon@minepeon bitstreams]$ cd /opt/minepeon [minepeon@minepeon minepeon]$ git checkout bin/scripts/FactoryReset.sh [minepeon@minepeon minepeon]$ git checkout bin/bitstreams/README error: pathspec 'bin/bitstreams/README' did not match any file(s) known to git. [minepeon@minepeon minepeon]$ git pull Updating 93b1f75..dfdac8b error: The following untracked working tree files would be overwritten by merge: bin/bitstreams/README Please move or remove them before you can merge. Aborting [minepeon@minepeon minepeon]$ rm bin/bitstreams/README [minepeon@minepeon minepeon]$ git pull Updating 93b1f75..dfdac8b Fast-forward bin/bfgminer | Bin 628076 -> 641762 bytes bin/bfgminer-rpc | Bin 9617 -> 9653 bytes bin/bitforce-firmware-flash | Bin 12261 -> 12377 bytes bin/bitstreams/README | 1 + bin/cgminer | Bin 838358 -> 736259 bytes bin/cgminer-gc3355 | Bin 0 -> 1514853 bytes bin/scripts/FactoryReset.sh | 1 + lib/libblkmaker-0.1.so.0.4.1 | Bin 12992 -> 13087 bytes lib/libblkmaker_jansson-0.1.so.0.4.1 | Bin 12345 -> 12333 bytes lib/libjansson.a | Bin 51296 -> 52296 bytes lib/libjansson.so.4.5.0 | Bin 44953 -> 45142 bytes lib/libusb-1.0.a | Bin 81526 -> 82114 bytes lib/libusb-1.0.so.2.0.0 | Bin 74778 -> 75203 bytes share/doc/bfgminer/AUTHORS | 3 +- share/doc/bfgminer/README | 46 +++++++++-- share/doc/bfgminer/README.RPC | 39 ++++++++- share/doc/bfgminer/rpc-examples/miner.php | 127 ++++++++++++++++++++++++------ 17 files changed, 181 insertions(+), 36 deletions(-) create mode 100644 bin/bitstreams/README create mode 100755 bin/cgminer-gc3355 [minepeon@minepeon minepeon]$
|
Rui Costa, Portugal - BTC : 1ct1aicGoUVpZeovsw3cCcPJZJHV5JXtW
|
|
|
kano
Legendary
Offline
Activity: 4592
Merit: 1851
Linux since 1997 RedHat 4
|
|
April 07, 2014, 01:26:06 PM |
|
... inside text of README: You must put the file fpgaminer_top_fixed7_197MHz.ncd in here for modminer to w$
Due to the pointlessness of mining BTC with FPGA, Con removed it since it was the largest file in the distribution and took up about 50% of the file space for everyone downloading cgminer but almost no one uses it - my MMQ sits with my other FPGA quietly watching my ASICs Just get it from a release before it was removed i.e. 3.12.3 or earlier (8-Feb-2014) As you can see in my last post, it is still there... [minepeon@minepeon minepeon]$ cd bin/bitstreams [minepeon@minepeon bitstreams]$ dir COPYING_fpgaminer README fpgaminer_top_fixed7_197MHz.ncd
Then git failed to delete it. It's not in cgminer.
|
|
|
|
oskuro
|
|
April 07, 2014, 10:41:32 PM |
|
Hi guys, i dont know what to do... I have raspberry pi with minepeon (MinePeon-0.2.4.6-RaspberryPi.img). Installed it into a sd card, and i use browser of my desktop to access minepeon on raspberry pi. I have to antminers U2 connected in an usb hub to the raspberry pi. I setup the pool in minepeon, but it says all the time that no devices running. I dont know what to do.
|
|
|
|
KyrosKrane
|
|
April 08, 2014, 06:07:37 AM |
|
Hi guys, i dont know what to do... I have raspberry pi with minepeon (MinePeon-0.2.4.6-RaspberryPi.img). Installed it into a sd card, and i use browser of my desktop to access minepeon on raspberry pi. I have to antminers U2 connected in an usb hub to the raspberry pi. I setup the pool in minepeon, but it says all the time that no devices running. I dont know what to do. What kind of hub are you using? If it's a USB3 hub, that won't work with a Raspberry Pi. Some folks have had success by plugging the USB3 hub into a USB2 hub, then plugging the USB2 into the Pi, but that doesn't always work either.
|
|
|
|
oskuro
|
|
April 08, 2014, 07:09:12 AM |
|
Hi guys, i dont know what to do... I have raspberry pi with minepeon (MinePeon-0.2.4.6-RaspberryPi.img). Installed it into a sd card, and i use browser of my desktop to access minepeon on raspberry pi. I have to antminers U2 connected in an usb hub to the raspberry pi. I setup the pool in minepeon, but it says all the time that no devices running. I dont know what to do. What kind of hub are you using? If it's a USB3 hub, that won't work with a Raspberry Pi. Some folks have had success by plugging the USB3 hub into a USB2 hub, then plugging the USB2 into the Pi, but that doesn't always work either. Yeah i have a rosewill usb2 hub. Finally i could make it work. I was so stupid and had the raspberry connected to the usb, but didnt have the usb connected to the raspberry pi using USB, LOL haha. one question now. The 2 antminers U2 are mining, but they are using default bfgminer. I would like to know if you recommend me better to use cgminer, and where can i find a tutorial for installing it. I just installed last minepeon version for raspberry pi, and then just setup the pool url with user and pass, and its mining, but i dont know if its better to use cgminer or not. Thanks!
|
|
|
|
mikerbiker6
|
|
April 08, 2014, 04:25:29 PM |
|
Hi, should minepeon work with the dualminer USB 2?(litecoin miner) Device is not recognized.
|
Participate and Earn on the Letstalkbitcoin forum letstalkbitcoin.com
|
|
|
teletobi
|
|
April 08, 2014, 07:58:25 PM Last edit: April 08, 2014, 09:10:17 PM by teletobi |
|
Still trying to get nxt running on minepeon. But as I'm a Linux noob I have two Questions:
1. Looks like there is no zip command installed. How could it be installed? 2. If thats not possible, is there a command to copy a whole Directory instead of file by file?
Got it: -r
Thanks, Teletobi
|
|
|
|
rctempire
Newbie
Offline
Activity: 6
Merit: 0
|
|
April 08, 2014, 09:18:12 PM |
|
Neil, Top work pal.
Really enjoying the Minepeon with ASIC Block Eruptor. Just purchased another PI to use Minepeon for the other Eruptors,
Is it as simple as adding ports into router to get remote access to the UI.
|
|
|
|
tripppn
|
|
April 09, 2014, 09:46:05 PM Last edit: April 10, 2014, 01:23:56 AM by tripppn |
|
Has anyone gotten piminer or something like piminer working with the new versions on minepeon yet? Really hate seeing this LCD screen go to waist.
|
“You can't be a real country unless you have a beer and an airline - it helps if you have some kind of football team, or some nuclear weapons, but in the very least you need a beer.” ― Frank Zappa
|
|
|
blackvoice
Newbie
Offline
Activity: 56
Merit: 0
|
|
April 20, 2014, 08:01:30 AM |
|
I am helping someone out on the latest version on the status page it has these fields. I am curious what is the Error and Utility showing. When using a 10 port hub getting 731 errors on one device and 0 Under utility for all devices.
In fact all devices are showing a ton of errors from 2 to 1800 all 9 Asic USB's. Does anyone have any tips to get the Errors down and Accepted up. 3 Accepted 5400 Errors Sad
I am worry about it
|
|
|
|
mikerbiker6
|
|
April 20, 2014, 08:49:41 AM |
|
I am helping someone out on the latest version on the status page it has these fields. I am curious what is the Error and Utility showing. When using a 10 port hub getting 731 errors on one device and 0 Under utility for all devices.
In fact all devices are showing a ton of errors from 2 to 1800 all 9 Asic USB's. Does anyone have any tips to get the Errors down and Accepted up. 3 Accepted 5400 Errors Sad
I am worry about it
Maybe your hub does not provide enough power for all your miners. try with only a few miners in the hub to test if this is the problem.
|
Participate and Earn on the Letstalkbitcoin forum letstalkbitcoin.com
|
|
|
mikejones
Newbie
Offline
Activity: 59
Merit: 0
|
|
April 22, 2014, 07:32:06 AM |
|
Do I have create an addtional/expand a partition?
|
|
|
|
mikejones
Newbie
Offline
Activity: 59
Merit: 0
|
|
April 22, 2014, 08:49:45 AM |
|
How do I update my minepeon to the most current version of cgminer through the command line?
|
|
|
|
tripppn
|
|
April 22, 2014, 04:04:06 PM |
|
I am helping someone out on the latest version on the status page it has these fields. I am curious what is the Error and Utility showing. When using a 10 port hub getting 731 errors on one device and 0 Under utility for all devices.
In fact all devices are showing a ton of errors from 2 to 1800 all 9 Asic USB's. Does anyone have any tips to get the Errors down and Accepted up. 3 Accepted 5400 Errors Sad
I am worry about it
If power ends up being your problem this is a great powered hub. It has enough juice to run 9 U1s and 1 U2 without problems. http://www.newegg.com/Product/Product.aspx?Item=N82E16817182208Look at the amps on your psu that powers your hub. assume each miner uses .5 amps. Its actually less cause this hub has a 4 amp psu and runs to but .5 is a good starting point then start adding more.
|
“You can't be a real country unless you have a beer and an airline - it helps if you have some kind of football team, or some nuclear weapons, but in the very least you need a beer.” ― Frank Zappa
|
|
|
tripppn
|
|
April 22, 2014, 04:06:38 PM |
|
Do I have create an addtional/expand a partition?
No. Just format the sdcard and put the img on it. As far as compiling the latest version of cgminer that's above my skill set. I just wait for the new img from mineforman
|
“You can't be a real country unless you have a beer and an airline - it helps if you have some kind of football team, or some nuclear weapons, but in the very least you need a beer.” ― Frank Zappa
|
|
|
MineForeman.com (OP)
Legendary
Offline
Activity: 896
Merit: 1000
|
|
April 22, 2014, 11:38:05 PM |
|
How do I update my minepeon to the most current version of cgminer through the command line?
If you are running the latest version (0.2.4.6) login via ssh and you will see a command menu. You can do it from there. Neil
|
|
|
|
|