fittsy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 04:55:27 PM |
|
What is the most profitable currently between pascal coin and decred?
I calculated my profitability between the two this morning and it was basically the same... within 1-2% or something if i remember correctly Decred has a lot of potential. They did a presentation to Coinbase. If they got picked up by Coinbase that would be huge. If you don't need to sell right away then Decred is of more interest than Pascal. Just my .02. I'm not a financial advisor and can't give financial advice but if you do a little research you'll see a massive difference between the two coins, the tech, their devs, and their community. To me it isn't worth a 1 or 2% difference. Decred could be 10% less profitable and I'd still mine it instead of Pascal.
|
|
|
|
messe
Newbie
Offline
Activity: 10
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 05:17:59 PM |
|
Hello, guys! I wanna ask if I can change Claymore's auto mining pool (1% fee) to other pool. Because i wanna change it to asian pool. I use the same internet to play games too, but when it's mining to europe server, i got massive lag. Is there any way to change it?
Thank you
|
|
|
|
asidamani
Newbie
Offline
Activity: 63
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 05:38:30 PM |
|
What is the most profitable currently between pascal coin and decred?
I calculated my profitability between the two this morning and it was basically the same... within 1-2% or something if i remember correctly Decred has a lot of potential. They did a presentation to Coinbase. If they got picked up by Coinbase that would be huge. If you don't need to sell right away then Decred is of more interest than Pascal. Just my .02. I'm not a financial advisor and can't give financial advice but if you do a little research you'll see a massive difference between the two coins, the tech, their devs, and their community. To me it isn't worth a 1 or 2% difference. Decred could be 10% less profitable and I'd still mine it instead of Pascal. The Decred has risen quite a lot recently. So it might rise as much.
|
|
|
|
fittsy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 06:59:31 PM |
|
Hello, guys! I wanna ask if I can change Claymore's auto mining pool (1% fee) to other pool. Because i wanna change it to asian pool. I use the same internet to play games too, but when it's mining to europe server, i got massive lag. Is there any way to change it?
Thank you
@Claymore maybe this is something to add to future release? Zone or Region or something? ZN or RN flags to the config? Maybe a new parameter like: zn: na zn: eu zn: cn zn: ru Then use the appropriate server for North America, European Union, China, Russia, etc.
|
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 07:19:17 PM |
|
Hello, guys! I wanna ask if I can change Claymore's auto mining pool (1% fee) to other pool. Because i wanna change it to asian pool. I use the same internet to play games too, but when it's mining to europe server, i got massive lag. Is there any way to change it?
Thank you
@Claymore maybe this is something to add to future release? Zone or Region or something? ZN or RN flags to the config? Maybe a new parameter like: zn: na zn: eu zn: cn zn: ru Then use the appropriate server for North America, European Union, China, Russia, etc. Miner uses same pool for devfee for most popular pools.
|
|
|
|
matmator
Sr. Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 487
Merit: 252
bou !
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 07:57:36 PM |
|
I been mining on 2 rigs for 2 months using: windows 7 ulti. h81 bro btc + Ram 8 GB + Intel Pentium Processor G3240 every rig have 5 cards of Sapphire nitro+ 480 8G 11260-01-20G set at 1342/2200 hashing 27.4-27.5 I saw people saying that it can be raises to 28-29 (without any mod or bios flash) only using overclock I would like to say the rigs are stable and working good with 16.11.5 (pow lim 0 & mv -24) The cards have samsung rams with asics (75-85) but all same hash 27.4-27.5 any help to raise would be appreciated even 0.5 for 10 cards it will be 5 Mh/s
My batch is: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal mywallet.Rig2 -epsw x -ethi 16 -esm 2 -mode 1 -tstop 80,75,75,75,75 -allcoins 1 pause
Hello 1342 it's too high! 1200/2200 or 1150/2150. and -48mv With bios mod you can have 30mh
|
go to the moon !!
|
|
|
imtav
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 79
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 08:28:05 PM |
|
DevFee mining happening too frequently! I have logs to show it. DevFee running at 16:07, then DevFee mining finished and I closed miner. Restarted miner, and again I'm seeing DevFee mining at 16:26. WTF??
|
|
|
|
bardacuda
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 08:51:04 PM |
|
The devfee always begins x minutes after you start mining (I think x=15...at least it did for the ZEC miner) and then every hour after that. Just don't stop or close the miner and it will only happen once per hour like it's supposed to.
|
The future will rely on AI. SingularityNET lets anyone create, monetize, and use AI at scale. From the creators of Sophia the Robot.
|
|
|
adly3000
Newbie
Offline
Activity: 55
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 10:00:03 PM |
|
I been mining on 2 rigs for 2 months using: windows 7 ulti. h81 bro btc + Ram 8 GB + Intel Pentium Processor G3240 every rig have 5 cards of Sapphire nitro+ 480 8G 11260-01-20G set at 1342/2200 hashing 27.4-27.5 I saw people saying that it can be raises to 28-29 (without any mod or bios flash) only using overclock I would like to say the rigs are stable and working good with 16.11.5 (pow lim 0 & mv -24) The cards have samsung rams with asics (75-85) but all same hash 27.4-27.5 any help to raise would be appreciated even 0.5 for 10 cards it will be 5 Mh/s
My batch is: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal mywallet.Rig2 -epsw x -ethi 16 -esm 2 -mode 1 -tstop 80,75,75,75,75 -allcoins 1 pause
Hello 1342 it's too high! 1200/2200 or 1150/2150. and -48mv With bios mod you can have 30mh Thank you so much. Ireduced to 1266/2200 same production. noticed on 1266/2250 showing 28 Mh/s but 2250 is the max on the msi afterburner which I dont like as it is the maximum, so returned to 1266/2200. I dont like any mod it might destroy card.
|
|
|
|
cashen
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 10:09:10 PM |
|
I'm duel mining (ETH+DCR) I've noticed some crazy performance. You can see it was solid all night but went wacky around 8AM. Any Ideas? ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FPBuaaB4.png&t=665&c=p5SKP66jJhzgCQ) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FPBuaaB4&t=665&c=jJXh04loaMLzFA)
|
|
|
|
Truthchanter
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 10:28:07 PM |
|
I'm duel mining (ETH+DCR) I've noticed some crazy performance. You can see it was solid all night but went wacky around 8AM. Any Ideas? ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FPBuaaB4.png&t=665&c=p5SKP66jJhzgCQ) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FPBuaaB4&t=665&c=jJXh04loaMLzFA) This might not be completely related to your issue but i find some of my cards need at least 5% power limit when dual mining or they don't hash as high (maybe even 10-15% for a couple cards). Although other cards seem to dual mine fine at 0% power limit. Another thing that comes to mind is if you have the target temp or max temp set too low and the cards may be throttling/downclocking if the heat gets too high. Otherwise its probably just random pool fluctuations or the normal way mining decred works.. idk
|
|
|
|
cashen
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 10:35:20 PM |
|
This might not be completely related to your issue but i find some of my cards need at least 5% power limit when dual mining or they don't hash as high (maybe even 10-15% for a couple cards). Although other cards seem to dual mine fine at 0% power limit. Another thing that comes to mind is if you have the target temp or max temp set too low and the cards may be throttling/downclocking if the heat gets too high. Otherwise its probably just random pool fluctuations or the normal way mining decred works.. idk
My fans are only running ~30%-40% and I think my target temps are set at 73C. I'm not sure about my max, but i'm not coming close. In Claymore the Hash rate always says 3000+. Its almost like they are not matching. I am wondering if it has to do with my poor wifi connecction.
|
|
|
|
Truthchanter
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 03, 2017, 10:39:18 PM |
|
This might not be completely related to your issue but i find some of my cards need at least 5% power limit when dual mining or they don't hash as high (maybe even 10-15% for a couple cards). Although other cards seem to dual mine fine at 0% power limit. Another thing that comes to mind is if you have the target temp or max temp set too low and the cards may be throttling/downclocking if the heat gets too high. Otherwise its probably just random pool fluctuations or the normal way mining decred works.. idk
My fans are only running ~30%-40% and I think my target temps are set at 73C. I'm not sure about my max, but i'm not coming close. In Claymore the Hash rate always says 3000+. Its almost like they are not matching. I am wondering if it has to do with my poor wifi connecction. Poor wifi definitely sounds like a potential culprit. although if you're not fluctuating too much at your eth pool then it just might be the nature of decred pools/mining.. maybe someone else would have a more knowledgeable answer about this
|
|
|
|
LJLT
Newbie
Offline
Activity: 48
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 12:27:13 AM |
|
I been mining on 2 rigs for 2 months using: windows 7 ulti. h81 bro btc + Ram 8 GB + Intel Pentium Processor G3240 every rig have 5 cards of Sapphire nitro+ 480 8G 11260-01-20G set at 1342/2200 hashing 27.4-27.5 I saw people saying that it can be raises to 28-29 (without any mod or bios flash) only using overclock I would like to say the rigs are stable and working good with 16.11.5 (pow lim 0 & mv -24) The cards have samsung rams with asics (75-85) but all same hash 27.4-27.5 any help to raise would be appreciated even 0.5 for 10 cards it will be 5 Mh/s
My batch is: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal mywallet.Rig2 -epsw x -ethi 16 -esm 2 -mode 1 -tstop 80,75,75,75,75 -allcoins 1 pause
Hello 1342 it's too high! 1200/2200 or 1150/2150. and -48mv With bios mod you can have 30mh Thank you so much. Ireduced to 1266/2200 same production. noticed on 1266/2250 showing 28 Mh/s but 2250 is the max on the msi afterburner which I dont like as it is the maximum, so returned to 1266/2200. I dont like any mod it might destroy card. Are you checking for memory erros with this setting?
|
|
|
|
cashen
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 12:37:08 AM |
|
This might not be completely related to your issue but i find some of my cards need at least 5% power limit when dual mining or they don't hash as high (maybe even 10-15% for a couple cards). Although other cards seem to dual mine fine at 0% power limit. Another thing that comes to mind is if you have the target temp or max temp set too low and the cards may be throttling/downclocking if the heat gets too high. Otherwise its probably just random pool fluctuations or the normal way mining decred works.. idk
My fans are only running ~30%-40% and I think my target temps are set at 73C. I'm not sure about my max, but i'm not coming close. In Claymore the Hash rate always says 3000+. Its almost like they are not matching. I am wondering if it has to do with my poor wifi connecction. Poor wifi definitely sounds like a potential culprit. although if you're not fluctuating too much at your eth pool then it just might be the nature of decred pools/mining.. maybe someone else would have a more knowledgeable answer about this No changes have been made to settings within the last 30 hours. Looks to be correcting slowly. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2F7HuhBz2.png&t=665&c=EbTx6cDSgkFW1A)
|
|
|
|
Junkey
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 02:40:41 AM |
|
Does the -mclock and -cclock options work in Linux for AMD RX400 cards?
|
|
|
|
adly3000
Newbie
Offline
Activity: 55
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 04:26:38 AM |
|
Thank you so much. Ireduced to 1266/2200 same production. noticed on 1266/2250 showing 28 Mh/s but 2250 is the max on the msi afterburner which I dont like as it is the maximum, so returned to 1266/2200. I dont like any mod it might destroy card.
Are you checking for memory erros with this setting? how can I? do you mean invalid shares. it is zero.
|
|
|
|
LJLT
Newbie
Offline
Activity: 48
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 04:44:28 AM |
|
Thank you so much. Ireduced to 1266/2200 same production. noticed on 1266/2250 showing 28 Mh/s but 2250 is the max on the msi afterburner which I dont like as it is the maximum, so returned to 1266/2200. I dont like any mod it might destroy card.
Are you checking for memory erros with this setting? how can I? do you mean invalid shares. it is zero. Download https://www.hwinfo.com/download.phpThere is an indicator for memory errors, they dont reflect in the number of shares but reduce the life of the card.
|
|
|
|
adly3000
Newbie
Offline
Activity: 55
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 06:20:21 AM Last edit: April 04, 2017, 07:35:34 AM by adly3000 |
|
Thank you so much. Ireduced to 1266/2200 same production. noticed on 1266/2250 showing 28 Mh/s but 2250 is the max on the msi afterburner which I dont like as it is the maximum, so returned to 1266/2200. I dont like any mod it might destroy card.
Are you checking for memory erros with this setting? how can I? do you mean invalid shares. it is zero. Download https://www.hwinfo.com/download.phpThere is an indicator for memory errors, they dont reflect in the number of shares but reduce the life of the card. Thank you so much.. Here is what I found: GPU0 - errors: 9 - Asic:79.5 GPU1 - errors: 1,794,151 - Asic:85.6 GPU2 - errors: 5123 - Asic:73.6 GPU3 - errors: 752 - Asic:75.8 GPU4 - errors: 88,873,330 - Asic:75 GPU5 - errors: 7811 - Asic:71.1 I reduced GPU1 and GPU4 to 1180/2200 @-24 mv tried 1160/2200 on GPU4 but hangs
|
|
|
|
kinsik
Newbie
Offline
Activity: 39
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 04, 2017, 06:32:11 AM |
|
Hi everyone. Please advice if 3-5% of stale shares in ethermine pool is fine. Please also advice what are the best values for -ethi and -etht.
Thanx
|
|
|
|
|