Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[ruplikminer]

Guys do you think it's better to mine DUAL ETH+XVG maybe? Or just one coin or shitcoin? I have 23x gtx 1070ti

[goodbitprofit]

Hello Guys,

I have one rig with 4x RX580. The primary GPU (GPU0) is conected to monitor. If i disconnect the monitor, and watch with Teamviewer,  Claymore (v11.0)  dont pass to initilize the GPU's .He stop to sequence  POLO/SOLO version and freeze. If i input the monitor cable , he go to the next step , find the GPU and make the dag for each one and finally work fine. I try to change the GPU0 and the same problem is present. Mean time the hrate for the GPU0 is less than the same GPU in not the GPU0.  

I have same problem on my 6x RX580 with MB Gygabite H110. It jumps from 20-30,5 MH\s

[LearningGuy]

Dear all,

Let me first say that i am very sorry that it took so long to get our pool NLpool.nl working correctly. When we put it online

You should correct your bat file format to below:

The address for XVG VERGE - Blake2s is:
stratum+tcp://mine.nlpool.nl:5766 -dwal <WALLET_ADDRESS> -dpsw c=XVG

NOT -u or -p

PS: I swapping some rigs to nlpool.. looking good now

Cheers Mike, coming to join

[ednet]

Hey guys. I have an eth mining rig of 6x RX570 8gb and i run it on Ethos using claymore.

I want to mine ETH and i want to dual-mine smart cash since DCR has asics now and i don't really see a future in XVG ^^.

The problem is that to mine Smart-Cash the alghoritm needs Claymore's version 11 and currently ethos only has v10. Any workaround? I have only found smart-cash pool's that uses claymore only..... If anyone is mining eth + smartcash on ethOS can i get some help please?

Thank you.

[Oggami]

It's just me or the version 11 as a virus in it....

[ruplikminer]

It's just me or the version 11 as a virus in it....

Shit your are fuked

[Kent2]

YES - Mine with NLPOOL
KOREPOOL - switch all to NLPOOL.
too much of small pools.

We need 2-5 TH, and then we have 1-2 blocks per hour, which is quite ok.

I just put 40 GH on nlpool. Works fine, i could suggest to start with higher diff - at least 10 or so.
Cause in the beggining there was a flood of shares ;-)

now the diff adjusted and is beetween 35 and 56.

What we need now is more hashpower so we can catch some blocks.

I did swap 2 RIGs on nlpool and I will swap 5 more.
If works decent, I will add 11 more RIGS.

Let's see.

i mining in NLPOOL 12 hours and my balance 0.00000 i think its scam
 and the miners continue to leave NLPOOL

[Call_Me_Bambi]

It's just me or the version 11 as a virus in it....

Most mining software is reported by virus scanners as being a virus. This is a false positive as in the past, and probably still today, mining software was surreptitiously installed on unsuspecting computers so the virus scanner take a cautious view of mining software.

[mine_phun]

i mining in NLPOOL 12 hours and my balance 0.00000 i think its scam
 and the miners continue to leave NLPOOL

That is impossible, you are doing something wrong. Contact me @ the e-mail address on the website please and send me your wallet address so i can check.

[Oggami]

It's just me or the version 11 as a virus in it....

Most mining software is reported by virus scanners as being a virus. This is a false positive as in the past, and probably still today, mining software was surreptitiously installed on unsuspecting computers so the virus scanner take a cautious view of mining software.

Thanks for the answer m8.

On another topic I'm getting this from NLPOOL

 DCR - Total Speed: 887.002 Mh/s, Total Shares: 10, Rejected: 10
 DCR: GPU0 887.002 Mh/s

Is this normal on the first 10 minutes?  

[LearningGuy]

Hello Guys,

I have one rig with 4x RX580. The primary GPU (GPU0) is conected to monitor. If i disconnect the monitor, and watch with Teamviewer,  Claymore (v11.0)  dont pass to initilize the GPU's .He stop to sequence  POLO/SOLO version and freeze. If i input the monitor cable , he go to the next step , find the GPU and make the dag for each one and finally work fine. I try to change the GPU0 and the same problem is present. Mean time the hrate for the GPU0 is less than the same GPU in not the GPU0.  

Why don’t you try some dummy plugs? I’ve seen multiple posts particularly and users requiring this.

https://www.newfrog.com/product/virtual-adapter-hdmi-dummy-plug-headless-ghost-display-emulator-4k3840x2160-190422?currency=ZAR&gclid=CjwKCAiAn5rUBRA3EiwAUCWb25WLe6OkhK8LzOJfdCjdEphOIGfXATCSDgWaVMC_XH0_25DwBkgr1RoCaaYQAvD_BwE

[Micmac14]

@mine_phun thx for the hard work and getting it sorted! Nlpool is working good for me.

[VicentMesdines]

In Nhpool the money is magic. It disappears.  

http://i64.tinypic.com/2dkjwax.png


Eiii, the money came backD. 

[cMoOn7799]

There's no good pool for XVG? Unimining gives about 40% of what it should give...EVEN IF Whattomine is not full accurate, the diference is too Huge...With 4600MH/s im getting only 12, 13 coins/day.

Antminepool doesnt work here on the last 5 or 6 days...instant disconnect on both ports.

You can use NLpool.nl now ... working and fast.

The address for XVG VERGE - Blake2s is:
stratum+tcp://mine.nlpool.nl:5766 -u <WALLET_ADDRESS> -p c=XVG

The address for Shield Blake2S is:
stratum+tcp://mine.nlpool.nl:5766 -u <WALLET_ADDRESS> -p c=XSH

If you have any questions or other coins you want added to the pool please e-mail us. The e-mail address is displayed on our website nlpool.nl

Example .bat :

EthDcrMiner64.exe -epool us2.ethermine.org:14444 -ewal <YOURETHADDRESS> -epsw x -gser 1 -lidag 1 -r 1 -dcri 40 -cclock 1150 -mclock 2125 -dpool stratum+tcp://mine.nlpool.nl:5766 -dwal <YourVergeAddress> -dcoin blake2s -dpsw c=XVG

I have 37 Rigs, am switching to your pool for 2 or 3 days & see how.

Hopefully will be able to bump up the network hash to over 4TH. Currently I'm seeing its 3.8TH on your pool.

[Oggami]

It's just me or the version 11 as a virus in it....

Most mining software is reported by virus scanners as being a virus. This is a false positive as in the past, and probably still today, mining software was surreptitiously installed on unsuspecting computers so the virus scanner take a cautious view of mining software.

Thanks for the answer m8.

On another topic I'm getting this from NLPOOL

 DCR - Total Speed: 887.002 Mh/s, Total Shares: 10, Rejected: 10
 DCR: GPU0 887.002 Mh/s

Is this normal on the first 10 minutes?  

  was missing -dcoin blake2s ......

[Teress]

Has anyone without a 'newbie' status tried NLPOOL? I'm curious what those more experienced verge miners think of the pool.

I switched there all my rigs few days ago, but mined NOTHING, that pool mined only 6 blocks in their whole history, last day. So I switched my rigs again away from them. Probably if they would have 1000x higher overall hashpower, it should be bettter, but I can't say at this moment they are correct or they are stealing shares like unimining.

what pool are you using?

Please read:

https://bitcointalk.org/index.php?topic=1433925.msg30398663#msg30398663

Again, i am very sorry that some blocks were lost, however this is solved now. I would appreciate it if we could make it up to you ;-)

Also, i would like to say that looking at the miners dashboard is see people mining XVG with the wrong password settings.

-p c=XVG-blake2s  <<< This is incorrect
-p c=XVG,ID=004_RX580_4   << Incorrect
-p x   << Incorrect.

The correct password for verge is c=XVG  nothing more, nothing less ;-)

How could you loose mined blocks?? I gave you all my rigs hashpower for two days and got nothing mined from you. So sorry, I don't trust your pool, because you stealed my shares. Thats simple.

Understood. Like i wrote, the Yiimp software is not free of bugs, so i made an error when i was bringing the pool online assuming all would be ok.
Sorry, but i am only human..... When we noticed this on monday i gave a message here that i took the pool offline because of this. Now that everything is fixed, i give the message here that all is ok now.

Well it is nice you apologize but that will not pay me bacl what you stealed from me. Imagine I will steale you 50 USD and tell you, I am sorry, I am only human....

[Koinmen]

Hey guys, I faced an interesting and annoying problem.

I have a 6 RX570 rig (5 samsung 1 hynix+elpida)

I successfully managed to get 29.5MH/s 1100/2000@838mV.

First minor problem, I couldn’t lower the voltage below 838mV nomatter if I set it to 800, it stuck on 838 or higher.

But my main question is, I tried to increase the memory clocks, I set them to 2100 and only the card's (which one is connected to a display) hashrate increased to +31MH/s, all rest of the cards Hash did not changed. In afterburner I seen the clocks were applied to all cards, tried Cryptonight algo and the OC worked there so it shouldn’t the cards.

I tried to increase voltage, Core clock, powerlimit, different versions of Claymore, different OC apps (Claymore too) nothing helped. I restarted the pc, the miner, used the numbers to disable the cards nothing.

try with  ASUS  GPU TweakII   software you can  oc one by one gpu

[Micmac14]

Has anyone without a 'newbie' status tried NLPOOL? I'm curious what those more experienced verge miners think of the pool.

I switched there all my rigs few days ago, but mined NOTHING, that pool mined only 6 blocks in their whole history, last day. So I switched my rigs again away from them. Probably if they would have 1000x higher overall hashpower, it should be bettter, but I can't say at this moment they are correct or they are stealing shares like unimining.

what pool are you using?

Please read:

https://bitcointalk.org/index.php?topic=1433925.msg30398663#msg30398663

Again, i am very sorry that some blocks were lost, however this is solved now. I would appreciate it if we could make it up to you ;-)

Also, i would like to say that looking at the miners dashboard is see people mining XVG with the wrong password settings.

-p c=XVG-blake2s  <<< This is incorrect
-p c=XVG,ID=004_RX580_4   << Incorrect
-p x   << Incorrect.

The correct password for verge is c=XVG  nothing more, nothing less ;-)

How could you loose mined blocks?? I gave you all my rigs hashpower for two days and got nothing mined from you. So sorry, I don't trust your pool, because you stealed my shares. Thats simple.

Understood. Like i wrote, the Yiimp software is not free of bugs, so i made an error when i was bringing the pool online assuming all would be ok.
Sorry, but i am only human..... When we noticed this on monday i gave a message here that i took the pool offline because of this. Now that everything is fixed, i give the message here that all is ok now.

Well it is nice you apologize but that will not pay me bacl what you stealed from me. Imagine I will steale you 50 USD and tell you, I am sorry, I am only human....

Bro chill. Dude had trouble getting the pool started I’m sure he didn’t steal from you. Go use zpool and quit your belly aching.

[Teress]

Has anyone without a 'newbie' status tried NLPOOL? I'm curious what those more experienced verge miners think of the pool.

I switched there all my rigs few days ago, but mined NOTHING, that pool mined only 6 blocks in their whole history, last day. So I switched my rigs again away from them. Probably if they would have 1000x higher overall hashpower, it should be bettter, but I can't say at this moment they are correct or they are stealing shares like unimining.

what pool are you using?

Please read:

https://bitcointalk.org/index.php?topic=1433925.msg30398663#msg30398663

Again, i am very sorry that some blocks were lost, however this is solved now. I would appreciate it if we could make it up to you ;-)

Also, i would like to say that looking at the miners dashboard is see people mining XVG with the wrong password settings.

-p c=XVG-blake2s  <<< This is incorrect
-p c=XVG,ID=004_RX580_4   << Incorrect
-p x   << Incorrect.

The correct password for verge is c=XVG  nothing more, nothing less ;-)

How could you loose mined blocks?? I gave you all my rigs hashpower for two days and got nothing mined from you. So sorry, I don't trust your pool, because you stealed my shares. Thats simple.

Understood. Like i wrote, the Yiimp software is not free of bugs, so i made an error when i was bringing the pool online assuming all would be ok.
Sorry, but i am only human..... When we noticed this on monday i gave a message here that i took the pool offline because of this. Now that everything is fixed, i give the message here that all is ok now.

Well it is nice you apologize but that will not pay me bacl what you stealed from me. Imagine I will steale you 50 USD and tell you, I am sorry, I am only human....

Bro chill. Dude had trouble getting the pool started I’m sure he didn’t steal from you. Go use zpool and quit your belly aching.

No I can't agree! When I will make my own pool, first before I put it on public I will have to be sure, everything is correct. He put his pool online as fast as possible to get as much profit from it. Tons of miners lost their money because of him. It is unanopologizable. Correct would be if he give to the users who lost their shares some reward as an apologize.

[valev1]

There's no good pool for XVG? Unimining gives about 40% of what it should give...EVEN IF Whattomine is not full accurate, the diference is too Huge...With 4600MH/s im getting only 12, 13 coins/day.

Antminepool doesnt work here on the last 5 or 6 days...instant disconnect on both ports.

You can use NLpool.nl now ... working and fast.

The address for XVG VERGE - Blake2s is:
stratum+tcp://mine.nlpool.nl:5766 -u <WALLET_ADDRESS> -p c=XVG

The address for Shield Blake2S is:
stratum+tcp://mine.nlpool.nl:5766 -u <WALLET_ADDRESS> -p c=XSH

If you have any questions or other coins you want added to the pool please e-mail us. The e-mail address is displayed on our website nlpool.nl

Example .bat :

EthDcrMiner64.exe -epool us2.ethermine.org:14444 -ewal <YOURETHADDRESS> -epsw x -gser 1 -lidag 1 -r 1 -dcri 40 -cclock 1150 -mclock 2125 -dpool stratum+tcp://mine.nlpool.nl:5766 -dwal <YourVergeAddress> -dcoin blake2s -dpsw c=XVG

I've just switched 15 rigs to your pool, lets hope for great income :-)