zac123
Newbie
Offline
Activity: 114
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 19, 2018, 06:54:07 PM |
|
3.7.2 was the last version to support GPU mining if I recall correctly. Maybe you would use that version for GPU mining on some old hardware with cheap electricity. The pre-built binaries are already there for you on 4.10 version. I don't understand going through the trouble of compiling a non-GPU executable for the last version of CGminer (3.7.2) that supported GPU mining. However, if you are just figuring out how to compile what you need that is great but it's already been done for you. ![Tongue](https://bitcointalk.org/Smileys/default/tongue.gif) Regarding the command line arguments, that older version of cgminer requires the Iccarus drivers to be compiled into the mix. As far as I know the Iccarus drivers were the earliest compatible with the Compac/Gekko Science USB devices. Again, neither of which you need. The CGminer documentation (3.7.X) states this in general https://github.com/vthoang/cgminer/blob/3.7/ASIC-README <--here "ASICMINER devices need the --enable-icarus option when compiling cgminer. Also note that the AMU is managed by the Icarus driver which is detailed in the FPGA-README. Configuring them uses the same mechanism as outlined below for getting started with butterfly labs ASICs." The address is correct for SlushPool configuration and it looks like you have setup your worker. The frequency argument is not right for the device "Gekko" as the "--gekko-compac-freq 200 " is not a feature of 3.7.x You may not have compiled the Iccarus drivers at all. Try "cgminer -ndev" to verify devices. _Edit_ ![Roll Eyes](https://bitcointalk.org/Smileys/default/rolleyes.gif) ---> Use the pre-built 4.10.x <---- thank you everyone for the help. i've had some time this eve to play with it and its working great. i'll continue to learn about it and get the most out of it.
|
|
|
|
vezpit
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 19, 2018, 08:06:53 PM |
|
I asked Eyeboot about it, he's gonna send me some samples to play with. He says they aren't as good, won't clock up as high.
Got them running using their version of cgminer. Run ok at stock frequency, zombie easily if increased the frequency.
|
|
|
|
QuarterMaster
Newbie
Offline
Activity: 28
Merit: 2
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 19, 2018, 10:31:08 PM |
|
I asked Eyeboot about it, he's gonna send me some samples to play with. He says they aren't as good, won't clock up as high.
Would rather support your work anyway especially with your dedication/support and new projects going on. These new TTBit sticks don'e exist to me.
|
|
|
|
Ichindar
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 23, 2018, 03:12:56 AM |
|
Hello ladies and gentlemen! I am a complete and utter newbie when it comes to mining Bitcoin and the rest. I recently purchased a GekkoScience 2Pac Stickminer and after dealing with some of the classic issues: (1) Not recognising the miner (2) Recognising the miner but not recognising any cores I am faced with a 3rd issue and I am stumped. Before we go further here is what my cgminer window looks like and my bat file I use to launch it. https://i.gyazo.com/06a1d6572551f6c8111d40c27c1e4c24.pnghttps://i.gyazo.com/0f19dd0176e16a70c058d865516bd8a5.pngMy miner will quite happily mine for a little bit until a success or two after that it will not mine anymore. I left it alone for 2 hours yesterday and my miner wasnt mining. The software kept telling me that a new block was detected at height xxxxxxxx. BUT if I unplug, wait for a few seconds and plug back in, the miner will mine again. Colour me stumped. ![Huh](https://bitcointalk.org/Smileys/default/huh.gif)
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 23, 2018, 03:34:52 AM |
|
Check the first post, specifically the power charts. I'll bet that'll give you at least a hit toward what's the problem.
|
|
|
|
Ichindar
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 23, 2018, 06:26:05 AM |
|
Check the first post, specifically the power charts. I'll bet that'll give you at least a hit toward what's the problem.
Thanks for your help chief! You are quite correct, the problem was the power. I found setting the frequency to 100 is the butter zone for me. I've been mining consistently for the first time beyond the first few 'accepts' for an hour now.
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 23, 2018, 12:22:38 PM |
|
That's what I figured. It started mining at 100 (the stock setting) then ramped up, and once power got too high something dropped out. Now you need to figure out if the limitation is your core voltage setting or the USB port.
|
|
|
|
Ichindar
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 23, 2018, 10:28:32 PM |
|
That's what I figured. It started mining at 100 (the stock setting) then ramped up, and once power got too high something dropped out. Now you need to figure out if the limitation is your core voltage setting or the USB port.
Until I actually buy a powered USB hub, I am using my PCs USB port so I dare say THAT is the issue. Do you have any suggestions as to a decent quality powered USB hub? I can get one for like $10-$20 but I am unsure as to the quality of el cheapo products.
|
|
|
|
sidehack
Legendary
Offline
Activity: 3374
Merit: 1859
Curmudgeonly hardware guy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 24, 2018, 02:52:51 AM |
|
Do a bit of searching. That question has been asked and answered more times than I care to think about, even spawning at least one entire thread on the subject. Since I don't run them for fun I don't have any actual recommendations. Also since I'm a cheapskate with skills, so when I need something I just go make it (or in this case, "upgrade" an $8 eBay hub).
|
|
|
|
AlexSDC
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 24, 2018, 05:44:13 AM |
|
Hello!
I have a the GekkoSience 2Pac working fine from the USB port of an HP Laptop but I cannot get it to work when running it from a Rosewill USB 2.0 10-Port hub. I know the hub is good since my Bitmain USB miner works fine when connect it to it.
Thank You for any help!
|
|
|
|
marousi
Newbie
Offline
Activity: 123
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 24, 2018, 07:12:43 AM |
|
Is the hub powered? what frequency you running the 2pac?
|
|
|
|
ricknamer
Jr. Member
Offline
Activity: 126
Merit: 1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 24, 2018, 11:11:32 AM |
|
That's what I figured. It started mining at 100 (the stock setting) then ramped up, and once power got too high something dropped out. Now you need to figure out if the limitation is your core voltage setting or the USB port.
Until I actually buy a powered USB hub, I am using my PCs USB port so I dare say THAT is the issue. Do you have any suggestions as to a decent quality powered USB hub? I can get one for like $10-$20 but I am unsure as to the quality of el cheapo products. Just buy a $10 eBay one if you're going to run one stick. If you end up running 2 or 3 go for a pluggable 60w 7 port USB hub for about $30 on Amazon
|
|
|
|
AlexSDC
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 24, 2018, 07:44:48 PM |
|
Is the hub powered? what frequency you running the 2pac?
Yes, The USB Hub is powered and the frequency is set to 150. Thank you for your reply.
|
|
|
|
ultimate64
Newbie
Offline
Activity: 18
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 25, 2018, 09:06:18 PM |
|
Hello miners friends, today I set up and launched USB STICK on my Acer AspireONE with Lubuntu and I'm connected to SlushPool. I must say that for now everything is ok, as I'm new to the world of miners I wanted some tips on how I could set CGMINER
|
|
|
|
marousi
Newbie
Offline
Activity: 123
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 26, 2018, 03:35:44 PM |
|
Your question is too vague
|
|
|
|
zac123
Newbie
Offline
Activity: 114
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 26, 2018, 04:05:40 PM |
|
Hello miners friends, today I set up and launched USB STICK on my Acer AspireONE with Lubuntu and I'm connected to SlushPool. I must say that for now everything is ok, as I'm new to the world of miners I wanted some tips on how I could set CGMINER
there are two settings that i can think of freq & voltage. are you starting your miner with a start.bat file? paste the command line here that you are using. regards zac
|
|
|
|
ultimate64
Newbie
Offline
Activity: 18
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 27, 2018, 08:16:44 PM |
|
Hello miners friends, today I set up and launched USB STICK on my Acer AspireONE with Lubuntu and I'm connected to SlushPool. I must say that for now everything is ok, as I'm new to the world of miners I wanted some tips on how I could set CGMINER
there are two settings that i can think of freq & voltage. are you starting your miner with a start.bat file? paste the command line here that you are using. regards zac How can I raise the frequency from file? and how can I create my start.bat file? now I throw everything manually ... thanks, ultimate.
|
|
|
|
zac123
Newbie
Offline
Activity: 114
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 28, 2018, 07:49:43 PM |
|
hello everyone,
ive got myself a powered usb station and i have two 2 pac miners. one is green one is black.
my question is will multiple sticks work under one 'worker name'? or should each stick be somehow given its own worker name in my start command line?
currently i connect to slushpool like so:
cgminer.exe -o stratum+tcp://eu.stratum.slushpool.com:3333 -u zbw123.worker1 -p x --gekko-2pac-freq 150
|
|
|
|
avulsionist
Jr. Member
Offline
Activity: 45
Merit: 1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 28, 2018, 11:18:50 PM |
|
my question is will multiple sticks work under one 'worker name'? or should each stick be somehow given its own worker name in my start command line?
I am pretty new to all this but it seems like one worker per cgminer instance is standard.
|
|
|
|
vezpit
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 29, 2018, 01:33:10 AM |
|
Sidehack FYI.
I ran two of the TTbits at the standard freq. of 100 (zombie if you raise the freq.) on their software with one Gekko at 100. All run, but not flash acceptance of shares. Mostly said stale share, then a bunch of acceptance & then back to a number of stale shares.
Set up the Gekko on another computer & ran at 150 on your software. Outperformed the TTbits by 2:1 with no stale shares. Think their software is one issue with the almost constant 'stale share' bit & the other issue is the marginal actual working performance. The (A) readings snapshot is:
Gekko A; 6640
TTbit (2) A; 2965
Conclusion is that the difference in performance indicates the TTbit should sell for less than USD$25.00 based upon performance, power/hash & poor software.
Comments? Other test I should try? Cheers Vezpit.
|
|
|
|
|