[GROUP BUY WORLDWIDE]BTMine v1 Miner 200GH/s BTC 2.4

[twib2]

I had also this kind of problem with 7-8 fuses and till now I bridged all the defect and it is running fine at 1500 but indeed it is not secure.
Do you know which kind of fuse we can use to replace the defect one?
If you can put a link with tech info because depending of the country, somethimes it is called a different way....

Thank you in advance,

Yep, not good at all - looks like you only have 5.5 workers functioning.  If you don't luck out with simply loose connectors, then either you're missing a ton of capacitors or (more likely) you've hit the fuse problem and will need either upgraded fuses or bridges to bypass them (dangerous but I've been running that way OC'd just fine for the last week+ full blast).  If your ribbon cable is torn from shipping, that'd do it, too, but no doubt you would have noticed that when you got the unit.

I'll see what I can come up with when I get home from work and can look at the fuses again.  I should be able to come up with size, voltage, and current ratings that you can use no matter where you live.  Hopefully.  ;-)

[1714666386]

1714666386

[malin]

K, I repair some fuses arent connect so I create baypases, and now i have like this:

It is some possible to locate concrete worker ?

[STATS] => 0
   [ID] => AVA0
   [Elapsed] => 479
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [baud] => 115200
   [miner_count] => 16
   [asic_count] => 10
   [timeout] => 9
   [frequency] => 1400
   [fan1] => 0
   [fan2] => 3240
   [fan3] => 3000
   [temp1] => 24
   [temp2] => -1
   [temp3] => -1
   [temp_max] => 24
   [Device Hardware%] => 10.4575
   [no_matching_work] => 247
   [match_work_count1] => 1618
   [match_work_count2] => 0
   [match_work_count3] => 1492
   [match_work_count4] => 1537
   [match_work_count5] => 731
   [match_work_count6] => 0
   [match_work_count7] => 1534
   [match_work_count8] => 1528
   [match_work_count9] => 1535
   [match_work_count10] => 1373
   [match_work_count11] => 1561
   [match_work_count12] => 0
   [match_work_count13] => 1586
   [match_work_count14] => 1471
   [match_work_count15] => 1088
   [match_work_count16] => 1475
   [Controller Version] => 0
   [Avalon Chip] => 55
   [USB Pipe] => 0
   [USB Delay] => r0 0.000000 w0 0.000000
   [USB tmo] => 26726 0

Yep, not good at all - looks like you only have 5.5 workers functioning.  If you don't luck out with simply loose connectors, then either you're missing a ton of capacitors or (more likely) you've hit the fuse problem and will need either upgraded fuses or bridges to bypass them (dangerous but I've been running that way OC'd just fine for the last week+ full blast).  If your ribbon cable is torn from shipping, that'd do it, too, but no doubt you would have noticed that when you got the unit.

I have in Api Log:

   [STATS] => 0
   [ID] => AVA0
   [Elapsed] => 240
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [baud] => 115200
   [miner_count] => 16
   [asic_count] => 10
   [timeout] => 9
   [frequency] => 1400
   [fan1] => 0
   [fan2] => 480
   [fan3] => 480
   [temp1] => 33
   [temp2] => -1
   [temp3] => -1
   [temp_max] => 33
   [Device Hardware%] => 6.2112
   [no_matching_work] => 170
   [match_work_count1] => 1
   [match_work_count2] => 0
   [match_work_count3] => 734
   [match_work_count4] => 750
   [match_work_count5] => 408
   [match_work_count6] => 0
   [match_work_count7] => 0
   [match_work_count8] => 746
   [match_work_count9] => 0
   [match_work_count10] => 678
   [match_work_count11] => 0
   [match_work_count12] => 0
   [match_work_count13] => 0
   [match_work_count14] => 696
   [match_work_count15] => 0
   [match_work_count16] => 0
   [Controller Version] => 0
   [Avalon Chip] => 55
   [USB Pipe] => 0
   [USB Delay] => r0 0.000000 w0 0.000000
   [USB tmo] => 13141 0

I think it isn't good ?;/

To change your fan speeds to slower speed use one these settings in the configurations, more options.  depending on how yours is wired, one will give you fastest fan speed and the other the slowest fan speed.

--avalon-fan 80-80

--avalon-fan 20-20

Mtnminer

Hi,

I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?


best regards

[twib2]

Much better, looks like you now have 12.5 units functioning, 3.5 not working.  Not sure what you mean by "concrete worker" though...    5 and 6 should be near the ribbon cable, so my guess is for those two, the board probably has got the capacitor problem (due to ribbon cable forcing a capacitor to come loose).  12 may be the case on the other blade.  Not sure about 2 though - could be that was one that you thought the fuse was OK, but is not?  There have been cases of misaligned pins in the backbone board that goes atop the blades, with pins even being bent outside the connector, so it might be worth a close inspection all around, both for loose capacitors and bad connections on the backplane.

K, I repair some fuses arent connect so I create baypases, and now i have like this:

It is some possible to locate concrete worker ?

[STATS] => 0
   [ID] => AVA0
   [Elapsed] => 479
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [baud] => 115200
   [miner_count] => 16
   [asic_count] => 10
   [timeout] => 9
   [frequency] => 1400
   [fan1] => 0
   [fan2] => 3240
   [fan3] => 3000
   [temp1] => 24
   [temp2] => -1
   [temp3] => -1
   [temp_max] => 24
   [Device Hardware%] => 10.4575
   [no_matching_work] => 247
   [match_work_count1] => 1618
   [match_work_count2] => 0
   [match_work_count3] => 1492
   [match_work_count4] => 1537
   [match_work_count5] => 731
   [match_work_count6] => 0
   [match_work_count7] => 1534
   [match_work_count8] => 1528
   [match_work_count9] => 1535
   [match_work_count10] => 1373
   [match_work_count11] => 1561
   [match_work_count12] => 0
   [match_work_count13] => 1586
   [match_work_count14] => 1471
   [match_work_count15] => 1088
   [match_work_count16] => 1475
   [Controller Version] => 0
   [Avalon Chip] => 55
   [USB Pipe] => 0
   [USB Delay] => r0 0.000000 w0 0.000000
   [USB tmo] => 26726 0

[malin]

K, tnx for advice, I will check it tomorrow:)

br

Much better, looks like you now have 12.5 units functioning, 3.5 not working.  Not sure what you mean by "concrete worker" though...    5 and 6 should be near the ribbon cable, so my guess is for those two, the board probably has got the capacitor problem (due to ribbon cable forcing a capacitor to come loose).  12 may be the case on the other blade.  Not sure about 2 though - could be that was one that you thought the fuse was OK, but is not?  There have been cases of misaligned pins in the backbone board that goes atop the blades, with pins even being bent outside the connector, so it might be worth a close inspection all around, both for loose capacitors and bad connections on the backplane.

[malin]

You don;t believe, I wake up morning and in api log form 3 AM I have:

[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: 54d7569
luci: 346e3e7
Socket connect failed: Connection refused


I i;m tired ;/

br

[malin]

k I will change mining and now all is ok.

[Gologuzan]

shipping fees, not customs/taxes, just shipping fees.

some ppl got their work places with magic. some expert in DHL wasn't able to read papers that some other DHL person filled, and now after making sweet and nice call since they are holding mine miner for 10 days so far, they fixed their mistake.

someone wrote that shipping costs were ~600euros. and person that got his/here job by magic got in his/here head that i need to pay those expenses.. and that person if only had looked 2 rows down would see that it has been paid by shipper. so company that i switched to, since DHL is playing with me, had to travel 2x to their main facility. that is total of 400 kilometers.

but i have managed to explain to them that they need to take some extra courses about their own jobs.

anyway false alarm. everything is ok.

thx for your concerns.

[blankdeleter]

To change your fan speeds to slower speed use one these settings in the configurations, more options.  depending on how yours is wired, one will give you fastest fan speed and the other the slowest fan speed.

--avalon-fan 80-80

--avalon-fan 20-20

Mtnminer

Hi,

I received my bitmines today, they work form 1h and fan1 and fan2 have still 3360 RPMS, Temp id 21 degree, hoe to set this fans slowest ?


best regards

Just wondering what is the best setup of fan speed that everyone is going for ?
Me after 3 weeks with my machines, the best combination for me is:

Chip Frequency(Default: 300) 1300 or 1400 (1500 drain too much energy, and increase the % of error too much so no point…
Target Temperature: 65
Overheat Cut Off Temperature: 75
More Options(Default: —quiet): --avalon-fan 20-20

These setup are giving me:
Temp1: 25
Temp2: 65
Temp3: -1

[twib2]

Just wondering what is the best setup of fan speed that everyone is going for ?
Me after 3 weeks with my machines, the best combination for me is:

Chip Frequency(Default: 300) 1300 or 1400 (1500 drain too much energy, and increase the % of error too much so no point…
Target Temperature: 65
Overheat Cut Off Temperature: 75
More Options(Default: —quiet): --avalon-fan 20-20

These setup are giving me:
Temp1: 25
Temp2: 65
Temp3: -1

Yep, there's no way you're going to be able to run at 1500 with those temps at that fan speed.  If I don't do anything to the fan speed, I'm at 29 and 41 and I can run 1500 no problem with about 4% error, which is perfectly fine. 

[grumpy619]

Just throwing this out there would anyone be interested I purchasing one of these machines? For 2500+ shipping? It runs flawless no busted caps no dead mods. Just throwing it out there.

[mtnminer]

What fan speeds are you seeing on your units.  I am getting 2880 rpm on the upgraded power unit running at 1500 mhz.  My other three units with the factory power supplies just can not keep the fan speeds up and I an running them under clocked until my other eight upgrade power supplies arrive.  They are all running fan speeds at about 2280 rpm, if I raise the mhz the fans speeds drop and eventually quit due to the weak factory power supplies!  One is still sitting cold just our of the box, waiting for the power supplies to arrive.

Mtnminer

Just wondering what is the best setup of fan speed that everyone is going for ?
Me after 3 weeks with my machines, the best combination for me is:

Chip Frequency(Default: 300) 1300 or 1400 (1500 drain too much energy, and increase the % of error too much so no point…
Target Temperature: 65
Overheat Cut Off Temperature: 75
More Options(Default: —quiet): --avalon-fan 20-20

These setup are giving me:
Temp1: 25
Temp2: 65
Temp3: -1

Yep, there's no way you're going to be able to run at 1500 with those temps at that fan speed.  If I don't do anything to the fan speed, I'm at 29 and 41 and I can run 1500 no problem with about 4% error, which is perfectly fine. 

[mtnminer]

You might want to try Ebay, that is more that we payed with power supplies and shipping and I personally will not be buying anymore of these, my lesson has been learned with this supplier.  I will be ordering antminers for 1.5 bitcoin very soon and for the long run until something better and proven comes along.

I wish you the best success with your sale.

Mtnminer

Just throwing this out there would anyone be interested I purchasing one of these machines? For 2500+ shipping? It runs flawless no busted caps no dead mods. Just throwing it out there.

[twib2]

Funny thing is that mine is miswired two ways, so not only are the settings backwards, it can't read the speeds.  So, I get the best cooling without specifying any --avalon-fan speed.  But I have no way of knowing what the speeds are.  ;-)  It's not the loudest (gets louder during startup cycling), but I'm guessing it's near 100% (down in the basement so no biggie).  I'm running both a Corsair HX1050 (on the main line) and an HX850 on the other blade.  I did try --avalon-fan 80 and 20, and got temps of 50 and 42, respectively.  Without that setting it likes 40, which is why I'm guessing 100%.

What fan speeds are you seeing on your units.  I am getting 2880 rpm on the upgraded power unit running at 1500 mhz.  My other three units with the factory power supplies just can not keep the fan speeds up and I an running them under clocked until my other eight upgrade power supplies arrive.  They are all running fan speeds at about 2280 rpm, if I raise the mhz the fans speeds drop and eventually quit due to the weak factory power supplies!  One is still sitting cold just our of the box, waiting for the power supplies to arrive.

Mtnminer

Just wondering what is the best setup of fan speed that everyone is going for ?
Me after 3 weeks with my machines, the best combination for me is:

Chip Frequency(Default: 300) 1300 or 1400 (1500 drain too much energy, and increase the % of error too much so no point…
Target Temperature: 65
Overheat Cut Off Temperature: 75
More Options(Default: —quiet): --avalon-fan 20-20

These setup are giving me:
Temp1: 25
Temp2: 65
Temp3: -1

Yep, there's no way you're going to be able to run at 1500 with those temps at that fan speed.  If I don't do anything to the fan speed, I'm at 29 and 41 and I can run 1500 no problem with about 4% error, which is perfectly fine. 

[grumpy619]

You might want to try Ebay, that is more that we payed with power supplies and shipping and I personally will not be buying anymore of these, my lesson has been learned with this supplier.  I will be ordering antminers for 1.5 bitcoin very soon and for the long run until something better and proven comes along.

I wish you the best success with your sale.

Mtnminer

Just throwing this out there would anyone be interested I purchasing one of these machines? For 2500+ shipping? It runs flawless no busted caps no dead mods. Just throwing it out there.

Yeah I figured was just testing the waters.

[mtnminer]

i honestly believe you will get a really go price for this on Ebay.  I am amazed at what Avalon clones sell for on the auction site.  It is where many people buy their first machines and get their feet wet in the mining world.

Mtnminer

You might want to try Ebay, that is more that we payed with power supplies and shipping and I personally will not be buying anymore of these, my lesson has been learned with this supplier.  I will be ordering antminers for 1.5 bitcoin very soon and for the long run until something better and proven comes along.

I wish you the best success with your sale.

Mtnminer

Just throwing this out there would anyone be interested I purchasing one of these machines? For 2500+ shipping? It runs flawless no busted caps no dead mods. Just throwing it out there.

Yeah I figured was just testing the waters.

[grumpy619]

i honestly believe you will get a really go price for this on Ebay.  I am amazed at what Avalon clones sell for on the auction site.  It is where many people buy their first machines and get their feet wet in the mining world.

Mtnminer

You might want to try Ebay, that is more that we payed with power supplies and shipping and I personally will not be buying anymore of these, my lesson has been learned with this supplier.  I will be ordering antminers for 1.5 bitcoin very soon and for the long run until something better and proven comes along.

I wish you the best success with your sale.

Mtnminer

Just throwing this out there would anyone be interested I purchasing one of these machines? For 2500+ shipping? It runs flawless no busted caps no dead mods. Just throwing it out there.

Yeah I figured was just testing the waters.

I know but the fees are retarded. I sold 600 worth of stuff and had like 45 bucks in fees alone... I might just try ebay though.. Trying to raise funds for 2 anti miners

[Hechay]

My miner just stopped working today.

Temp1,Temp2 is 0 degree C. I removed the temp sensor before.

Avg Hash is always 0 too.

Is anyone get same problem like me?

[Hechay]

The LED is red What happened to it?

[Hechay]

Try to run cgminer manually via ssh, got this result: ( the fan is not running )

Code:

[2014-02-02 06:21:29] Started cgminer 3.4.3                    
 [2014-02-02 06:21:30] AVA0: Reset succeeded (Controller version: 2013110865)                    
 [2014-02-02 06:21:30] AVA0: Idling 16 miners                    
 [2014-02-02 06:21:30] Probing for an alive pool                    
 [2014-02-02 06:21:31] Pool 0 difficulty changed to 26.666260                    
 [2014-02-02 06:21:31] Pool 1 difficulty changed to 2                    
 [2014-02-02 06:21:32] Pool 1 difficulty changed to 256                    
 [2014-02-02 06:21:36] API running in IP access mode on port 4028 (12)                    
 [2014-02-02 06:21:42] AVA0: Result return rate low, resetting!                    
 [2014-02-02 06:21:42] AVA0 reset sequence sent                    
 [2014-02-02 06:21:42] AVA0: Idling 11 miners                    
 [2014-02-02 06:21:47] AVA0: Result return rate low, resetting!                    
 [2014-02-02 06:21:47] AVA0 reset sequence sent                    
 [2014-02-02 06:21:48] AVA0: Idling 12 miners                    
 [2014-02-02 06:21:53] AVA0: Result return rate low, resetting!                    
 [2014-02-02 06:21:53] AVA0 reset sequence sent                    
 [2014-02-02 06:21:53] AVA0: Idling 12 miners                    
 [2014-02-02 06:21:59] AVA0: Result return rate low, resetting!                    
 [2014-02-02 06:21:59] AVA0 reset sequence sent                    
 [2014-02-02 06:21:59] AVA0: Idling 11 miners                    
 [2014-02-02 06:22:04] AVA0: Result return rate low, resetting!                    
 [2014-02-02 06:22:04] AVA0 reset sequence sent                    
 [2014-02-02 06:22:04] AVA0: Idling 12 miners                    
(5s):0.000 (avg):0.000h/s | A:0  R:0  HW:0  WU:0.0/m 

[Hechay]

I found my problems. When I tried to remove the first Psu and change it to the second. The fan of PSU is not blow. When I removed the PCI-E and CPU electric cable, the PSU blow again.

Can I anyone explain this thing?