[GROUP BUY WORLDWIDE]BTMine v1 Miner 200GH/s BTC 2.4

[slavo]

ok but how can i ssh  

no i'm dead. It's connecting. Just receiving nothing.

[1714701825]

1714701825

[1714701825]

1714701825

[1714701825]

1714701825

[sikke]

1)  Sorry, I should have described the location better, but perhaps you don't have any modules with FUSE1 silk-screened?  All but one of mine did, but I think I got an early version.  I did not take pics, but using another user's pics I'll point out where that single fuse is on his dual-fuse (newer?) version.  Top left component right next to far left large capacitor, the fuses in parallel which don't seem to be a problem (so far) are marked with a single "P".  At that same location on the boards with FUSE1, there will be a single FUSE1 fuse, with two other small components just below it.  Hope that helps.

Thanks man! I was waiting this info. I just replaced 2x stock psu with two Thermaltake 850w 70A single rail psu and overclocked to 1500. i will do shorting of thoes fuses tomorrow.

Two Thermaltake 850w with 5 cold chips not hashing
1400 stock 878w
1500 OC 947w

it's hashing 222.64 GH/s to BTCGuild with 5 cold chips. Temps are no issue my location is cold.

[FarmerOak]

1)  Sorry, I should have described the location better, but perhaps you don't have any modules with FUSE1 silk-screened?  All but one of mine did, but I think I got an early version.  I did not take pics, but using another user's pics I'll point out where that single fuse is on his dual-fuse (newer?) version.  Top left component right next to far left large capacitor, the fuses in parallel which don't seem to be a problem (so far) are marked with a single "P".  At that same location on the boards with FUSE1, there will be a single FUSE1 fuse, with two other small components just below it.  Hope that helps.

Thanks man! I was waiting this info. I just replaced 2x stock psu with two Thermaltake 850w 70A single rail psu and overclocked to 1500. i will do shorting of thoes fuses tomorrow.

Two Thermaltake 850w with 5 cold chips not hashing
1400 stock 878w
1500 OC 947w

it's hashing 222.64 GH/s to BTCGuild with 5 cold chips. Temps are no issue my location is cold.

Seems like most of us have at least 1 set of 5 chips that are dead (I don't mean the FUSE1 issue). I hope we can come up with a solution that doesn't involve reflowing the whole board... or a way to get BTmine to send us all an additional module to make up for the busted ones. I'd even settle for buying one at a reasonable cost.

[babaji.ca]

it's official....it's the.....

[robbcarpdm]

in the browser i see

LuCI - Lua Configuration Interface

then

problem, can't reach page 192.168.0.55. (or sth like that i have a french version)

It seems as a defective firmware then no ? I can see every piece. the blades can connect the laptop, and the laptop sees the wifi and eth connection from the miner.

any reboot button ? or a way to flash firmware from a computer ?

For give me if you are past this but...... have you tried switching your router so that it is 192.168.0.1  so that the nodes are in the same network?

Your first post you have 192.168.1.1 for your router but the device is 192.168.0.174


IE the 1 and 0 need to match I think

[slavo]

already done watch last page

nothing happens that's all, the connection miner/laptop is working fine, just no interface.

[slavo]

someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

[udt89]

12 days since order and not a thing.

This thing arrives with anything DOA I'm filing a claim. Screw them

[robbcarpdm]

Well I had a very good tech guy get my miners online.... going to pay him to watch my farm.

They are bouncing betweeen 200 -240 will see the avg after 24 hrs.

NO OC ......I am stopping by microcenter tonight to a bunch of heatsink supplies etc....and will let the units burn in before I take the chances the rest you like to do.

I dont want to lose my warranty until I know these are not the pieces of crap the rest of you got.....laughing,

Cheers,

[miaviator]

someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

Why not let someone team viewer in and help you.

[Pistachio]

someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

Are you sure it's not your PSU? I had the same screen issue when I tried to run it from a blown PSU. The intro screen popped up and then went dead. Does the loud fan come on?

If the FPGA module is not working, use a laptop and control it with cgminer via USB. cgminer 3.9.0 should work fine.

[mtnminer]

CGMiner 3.10.0 is having problems connecting to some pools
https://www.btcguild.com/index.php?page=home

Mtnminer

someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

Are you sure it's not your PSU? I had the same screen issue when I tried to run it from a blown PSU. The intro screen popped up and then went dead. Does the loud fan come on?

If the FPGA module is not working, use a laptop and control it with cgminer via USB. cgminer 3.9.0 should work fine.

[Professoruss]

Just opened one of the boxes up, looks like i got some free PSU's at least for this unit.  Should I just toss them?  Connections look ok inside.

[slavo]

someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

Are you sure it's not your PSU? I had the same screen issue when I tried to run it from a blown PSU. The intro screen popped up and then went dead. Does the loud fan come on?

If the FPGA module is not working, use a laptop and control it with cgminer via USB. cgminer 3.9.0 should work fine.

yes the fan are ultra loud 80 or 100% i'd say.

ok i'll check this tomorrow and i'll ask another module.

thanks.

first, thanks everybody for help.

I found the reset button and it worked. I can now access the interface ! 18 hours later finally.

So I setup the wifi, that's currently working fine on a new ip.

Now my problem is :

[Firmware Version] => 20130821
cgminer-70bc62c
luci-d854edc+
cgminer-openwrt-packages-800cc58
Socket connect failed: Connection refused


any ideas ?

[cannachris]

just got my miner today i ordered on the 8th

working very well , but loud...

do the temperature control parameters override the fan  settings? can i kill my miner by turning the fans to a too low speed? is it possible to run the chips safely at 1425 or 1450 with the stock psu's?

[Professoruss]

just got my miner today i ordered on the 8th

working very well , but loud...

do the temperature control parameters override the fan  settings? can i kill my miner by turning the fans to a too low speed? is it possible to run the chips safely at 1425 or 1450 with the stock psu's?

you using the included psu?  are you in the US?

[grumpy619]

I was running on one psu but the other blade was taken out in the process. I'm going to try the other ting you said lets see if it works.

[Pistachio]

someone knows how to mine by pluggin the usb to my laptop  ? Version of cgminer / .bat to use ?

i pm'd btmine, if they can ship the defective part and I can mine connected to a computer I'll be happy.

Are you sure it's not your PSU? I had the same screen issue when I tried to run it from a blown PSU. The intro screen popped up and then went dead. Does the loud fan come on?

If the FPGA module is not working, use a laptop and control it with cgminer via USB. cgminer 3.9.0 should work fine.

yes the fan are ultra loud 80 or 100% i'd say.

ok i'll check this tomorrow and i'll ask another module.

thanks.

For cgminer 3.90, use zadig http://zadig.akeo.ie/ to switch the drivers to winUSB. Then just start cgminer and it should pick it right up.

[Slander]

just got my miner today i ordered on the 8th

working very well , but loud...

do the temperature control parameters override the fan  settings? can i kill my miner by turning the fans to a too low speed? is it possible to run the chips safely at 1425 or 1450 with the stock psu's?

Same here, ordered on the 8th, arrived today. Opened up to check connections, all fine, I did nothing. 20 mins later Im hashing away at 214 ghash. Running off wifi, it worked instantly, I didnt have to mess with it at all other than screw in the ant.

It is MUCH quieter than I expected, my open air litecoin rigs running 7970's make way more noise.

The cases are really slick, they look and feel very industrial.

Overall I am very happy with everything, wish I bought more of them.

Time to start tweaking to squeeze a bit more out of it.

[udt89]

Finally got tracking number.  The 22nd their time. 12 days after order date. 4 days after promised ship date.  Only positive is he accepts PayPal.