wpgdeez
|
|
May 12, 2014, 01:48:09 PM |
|
1 of my S1's was dead this morning, thought it was a bad psu. Plugged it into another and one of the caps exploded and started on fire! This is it for me now for sure.
I find that highly unlikely. Capacitors of the size found on the S1 aren't large enough to cause a fire unless you're stacking your S1s on top of gasoline or something. It's always possible that there was some freak accident, I suppose. It exploded as soon as I turned on the psu. POP. I was able to blow it out right away. All thats left is the inside of the cap all charred. It was the big silver one located just below and to the right of the 6 pin connector. I will post a pic tomorrow. It probably would have extinguished itself if I hadn't been there but its always a little scary with electrical fires.It doesn't look like there is much on the board to go up in flames but who knows. Lesson learned, I am getting a dry extinguisher asap just to be safe. And I would be happy to replace the S1 with a S2 if I was given a super awesome coupon for the trouble. Win-Win. Considering I have ordered 30 ants and this is the first bad blade its not too bad, 1 out of 60.
|
|
|
|
jewgalo
Newbie
Offline
Activity: 44
Merit: 0
|
|
May 12, 2014, 02:06:29 PM |
|
anyone in canada have experience with getting these ants... whats the customs procedure like? how much did you end up paying in taxes / duties?
About $26 a machine. No customs issues, just pay the man when he comes to your door. Its even cheaper for multiples. My last order of 9 averaged $18 per ant. Shipping is fast and smooth, no problem getting them in the country. About the same here, 92$ for each of my 5 unit orders brooo thats nowhere near the same as $26 / $18 per unit... really dont wanna get stuck paying around $100 x 8 units... in the comments section if i ask them to put a low value on it will they oblige...? Anyone want a voucher for a S2?
how much is it for and what are you looking to get for it? when does it expire? Bro, 92\5=18.40 that was totally my bad i didn't fully read your post i guess... i thought you meant $92 per unit....
|
|
|
|
windpath
Legendary
Offline
Activity: 1258
Merit: 1027
|
|
May 12, 2014, 03:27:57 PM |
|
Considering I have ordered 30 ants and this is the first bad blade its not too bad, 1 out of 60. That is a little scary... I've got 6 ants, been running for a while now with no real issues. After I had it up and running I noticed 1 of the ants is missing 2x of the same capacitor that you had pop (in a different location on the PCB), seems to be running fine though...
|
|
|
|
aztecminer
Legendary
Offline
Activity: 1092
Merit: 1000
|
|
May 12, 2014, 09:03:36 PM |
|
i just ordered a bunch of those for my ants.. how are they working for you ?? I'm happy with them. Good bang for you buck. M got them installed today.. they work well with the heatsinks. i am seeing low to mid 40's temps @400 mhz.. i think is good for fan redundancy too. i used #8 1 1/2 bolts worked great.
|
|
|
|
jewgalo
Newbie
Offline
Activity: 44
Merit: 0
|
|
May 12, 2014, 09:09:26 PM |
|
is it safe to be running the ants 24/7 with an empty house 5 days a week for 8 hours or so... getting a little concerned of them blowing up or catching fire...
|
|
|
|
DebitMe
Legendary
Offline
Activity: 2800
Merit: 1012
Get Paid Crypto To Walk or Drive
|
|
May 12, 2014, 09:10:28 PM |
|
is it safe to be running the ants 24/7 with an empty house 5 days a week for 8 hours or so... getting a little concerned of them blowing up or catching fire...
As long as you have them correctly powered and cooled, there should be no issue and nothing to worry about.
|
|
|
|
jewgalo
Newbie
Offline
Activity: 44
Merit: 0
|
|
May 12, 2014, 09:15:45 PM |
|
is it safe to be running the ants 24/7 with an empty house 5 days a week for 8 hours or so... getting a little concerned of them blowing up or catching fire...
As long as you have them correctly powered and cooled, there should be no issue and nothing to worry about. won't be overclocking them until the warranty is up and plan on using corsair 80 plus gold 850W for each miner + stock fans...
|
|
|
|
wpgdeez
|
|
May 12, 2014, 09:25:57 PM |
|
is it safe to be running the ants 24/7 with an empty house 5 days a week for 8 hours or so... getting a little concerned of them blowing up or catching fire...
As long as you have them correctly powered and cooled, there should be no issue and nothing to worry about. My ant was the only device on a 20 amp breaker using a 800 watt PSU. Shit happens.
|
|
|
|
aztecminer
Legendary
Offline
Activity: 1092
Merit: 1000
|
|
May 12, 2014, 09:30:10 PM |
|
is it safe to be running the ants 24/7 with an empty house 5 days a week for 8 hours or so... getting a little concerned of them blowing up or catching fire...
As long as you have them correctly powered and cooled, there should be no issue and nothing to worry about. My ant was the only device on a 20 amp breaker using a 800 watt PSU. Shit happens. are u going to try to replace the popped cap ?? it probably wouldn't be that difficult . do u know how to solder ??
|
|
|
|
wpgdeez
|
|
May 12, 2014, 09:35:38 PM |
|
is it safe to be running the ants 24/7 with an empty house 5 days a week for 8 hours or so... getting a little concerned of them blowing up or catching fire...
As long as you have them correctly powered and cooled, there should be no issue and nothing to worry about. My ant was the only device on a 20 amp breaker using a 800 watt PSU. Shit happens. are u going to try to replace the popped cap ?? it probably wouldn't be that difficult . do u know how to solder ?? I thought about it but want see what Bitmain does with the RMA. Pm'd them yesterday and got a response asking for my email. Havent heard back yet but Im sure they do sleep Im not going to rake them over the coals, these things happen to all sorts of electronics, just bad luck. Hoping they step up to the plate and give me some GOOD coupons as a gesture of good faith. If I see a juicy coupon then I can buy more gear. S2 for $1800 would be nice
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
May 13, 2014, 01:18:16 AM |
|
Considering I have ordered 30 ants and this is the first bad blade its not too bad, 1 out of 60. That is a little scary... I've got 6 ants, been running for a while now with no real issues. After I had it up and running I noticed 1 of the ants is missing 2x of the same capacitor that you had pop (in a different location on the PCB), seems to be running fine though... i had that capacitor fall off on one of my units. booting via a PSU-on would cause some chips on that side to not detect properly, but if i rebooted the antminer while leaving the 12V power on,it recognizes and runs just fine. In the case of WPGDEEZ's unit: 1) did you possibly connect the 12V and GND backwards? this could cause angry capacitors and other damage. 2) clean everything up, remove the cap, and if there is no other damage (such as burnt traces, other swollen caps, or cracked resistors) try turning it on. I give you a 60% chance that it will boot and operate just fine without that capacitor if there's no other issues. (please double-check your wiring polarity first)
|
|
|
|
GIXXER
Newbie
Offline
Activity: 10
Merit: 0
|
|
May 13, 2014, 01:25:22 AM |
|
anyone in canada have experience with getting these ants... whats the customs procedure like? how much did you end up paying in taxes / duties?
No problems getting to Canada. I paid a bit for taxes or broker fees wasnt sure didnt care enough too look because it wasnt that much.2132 Price dropped down to $213 for a S1 today. Makes me wonder if they're unloading these for a reason.
|
|
|
|
windpath
Legendary
Offline
Activity: 1258
Merit: 1027
|
|
May 13, 2014, 01:55:14 AM |
|
2) clean everything up, remove the cap, and if there is no other damage (such as burnt traces, other swollen caps, or cracked resistors) try turning it on. I give you a 60% chance that it will boot and operate just fine without that capacitor if there's no other issues. (please double-check your wiring polarity first)
I think this is a good idea, as long as your around to monitor it for a while.... Again, mine with 2 of those capacitors missing, in a different location, runs fine. There was a "common sense" fire safety thread I contributed to a while ago, but cant seem to find it. 90% of the time turning the power off (away from the fire, like at the breaker) will extinguish any electrical fire quickly, assuming you are there when it starts. Clean it up, inspect it and if all else looks OK give it a shot (with your hand on the breaker )
|
|
|
|
BillTech
|
|
May 13, 2014, 02:49:42 AM |
|
looks like the caps in that area might have had a hard bump notice smaller cap to the left is off kilter?
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4270
Merit: 8676
'The right to privacy matters'
|
|
May 13, 2014, 03:38:11 AM |
|
looks like the caps in that area might have had a hard bump notice smaller cap to the left is off kilter?
yep and the one that blew was most likely just barely disconnected causing an arc and a pop. You can run that s-1 with 1 blade. just make sure the good blade is properly attached to the controller. if you have one blade and the controller running you get 100gh then just rma the 1 dead board. there is a thread were someone had a dead blade I told him to switch the controller to the good blade it ran at 1/2 speed and he rma'd the one dead blade. link https://bitcointalk.org/index.php?topic=597800
|
|
|
|
lowbander80
Legendary
Offline
Activity: 1036
Merit: 1000
|
|
May 13, 2014, 05:52:53 AM |
|
I would like to inform the BItmain community about what happened to me with my purchase from bitmain
I am very very SORRY but there one more UNHAPPY AND SCREWED CUSTOMER OF BITMAIN
UNHAPPY AND SCREWED CUSTOMER OF BITMAIN UNHAPPY AND SCREWED CUSTOMER OF BITMAIN UNHAPPY AND SCREWED CUSTOMER OF BITMAIN
ON 16/4/2014 just before Easter I ordered 2 x S1 antminers.
I have made a payment for 2pcs Antminer S1 on 16/4/2014 and up to today 28 days later nothing has arrived please help
Order number
00120140415051311075KBr9n9xw06B7
tracking EMS (available already sent to BITMAIN MORE THAN ONE TIME)
Aparently I have lost my bitcoins lost my miners and I receive no HELP FROM BITMAIN....
I have lost one month mining plus my original of hard earned bitcoins...
I am not sure what will happen but for now am deeply dissapointed!!!!!!!
PLEASE HELP BITMAIN DONT LET YOUR CUSTOMERS DOWN.......
FIRST REPLY FROM BITMAIN
------------------------------------------------------------ Hi, Sorry for the inconvenience. We've requested EMS to double check the status and haven't get any result. I'll inform you once get any update. Thanks for your patience! Best Regards, ------------------------------------------------------------- Second reply from Bitmain
Hi, Sorry for the delay. We'll contact EMS to follow them right away and try to push them each day before getting the info. Thanks for your supportJ
-------------------------------------------------------------------
third reply from Bitmain
Hi,
Very sorry for the inconvenience. We’ve called the EMS manager and he promised to provide an answer today.(two days ago) I’ll inform you if any update. Thanks for your patience. Best Regards,
How would you rate thiS CUstoMER support
If I receive any help or compensation or refund from BITMAIN I PROMISE TO WRITE IT HERE AND EDIT MY POST
IF NOT BITMAIN HERE IS YOUR GLORY
|
|
|
|
BITMAIN (OP)
|
|
May 13, 2014, 10:51:08 AM |
|
New price for AntMiner S1: 0.476 btc each one, shipping cost included.
|
Cloud Mining? Just Go to Hashnest.com Best Liquidity Lowest Price 100% Real Mining Back Up
|
|
|
rhj12345
|
|
May 13, 2014, 12:06:00 PM |
|
I have made a payment for 2pcs Antminer S1 on 16/4/2014 and up to today 28 days later nothing has arrived please help
I really feel your pain. I hope this get resolved by them soon. Have you reached out to Bitmain here in the forum? I can't know the customer service problems you are having as everyone of my units was sent to me within 3 to 4 days and without an issue. Hope you find help soon!
|
|
|
|
wpgdeez
|
|
May 13, 2014, 01:33:35 PM |
|
looks like the caps in that area might have had a hard bump notice smaller cap to the left is off kilter?
yep and the one that blew was most likely just barely disconnected causing an arc and a pop. You can run that s-1 with 1 blade. just make sure the good blade is properly attached to the controller. if you have one blade and the controller running you get 100gh then just rma the 1 dead board. there is a thread were someone had a dead blade I told him to switch the controller to the good blade it ran at 1/2 speed and he rma'd the one dead blade. link https://bitcointalk.org/index.php?topic=597800Yeah, that's the first thing I did, running at 95 ghash. It's not worth trying to revive the blade imo, its not trustworthy or worth the risk.
|
|
|
|
hdbuck
Legendary
Offline
Activity: 1260
Merit: 1002
|
|
May 13, 2014, 02:26:51 PM |
|
New price for AntMiner S1: 0.476 btc each one, shipping cost included.
wahhh so until how much you can drop the price before selling at manufacturing loss?
|
|
|
|
|